Effects of Scale and Discharge Variation on Similitude and Solute Transport in Water Treatment Tanks
Publication: Journal of Environmental Engineering
Volume 140, Issue 1
Abstract
This paper addresses the design and experimentation aspects of scaled contact tanks, a key type of treatment units in water works worldwide. The paper covers the effects of scale and discharge variation on the dynamic similitude and hydraulic efficiency of such tanks. The flow patterns tending to complete mixing (CM) and plug flow (PF) were studied, each assessed in a prototype and three further geometrically similar models of L-shaped and serpentine geometries. Tracer experiments were conducted under five discharge values. The sensitivity of each flow pattern to the changing conditions was assessed based on the residence time distribution curves and hydraulic efficiency index values, contrasted for prototypes and their scaled models. Although the CM flow pattern was insensitive to the variation of scale and discharge, within the ranges tested in this study, the PF pattern was affected by both variations when the flow regime was not turbulent in a model tank. A dependency of the dispersion number on the Reynolds number was observed, leading to the proposal of a new model to support the design and upscaling of results in contact tank studies.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
We thank the anonymous reviewers for their suggestions to improve the manuscript and acknowledge the support of the Postgraduate Programme in Environmental Engineering of Federal University of Espirito Santo (PPGEA/UFES, Brazil) and a scholarship provided by the Brazilian National Council for Research and Development (CNPq).
References
Chadwick, A., Morfett, J., and Borthwick, M. (2004). Hydraulics in civil and environmental engineering, 4th Ed., Routledge, London.
Elder, J. W. (1959). “The dispersion of marked fluid in turbulent shear flow.” J. Fluid Mech., 5(4), 544–560.
Figueiredo, I. C. (2000). “A study of the influence of hydrodynamics and microorganisms upon the chlorine dosage required for water disinfection.” M.Sc. dissertation, Dept. of Environmental Engineering, UFES, Brazil (in Portuguese).
Gerritsen, H., et al. (2011). “Composite modelling of interactions between beaches and structures.” J. Hydraul. Res., 49(S1), 2–14.
Hart, F. L., and Gupta, S. K. (1978). “Hydraulic analysis of model treatment units.” J. Environ. Eng. Div., 104(4), 785–798.
Heller, V. (2011). “Scale effects in physical hydraulic engineering models.” J. Hydraul. Res., 49(3), 293–306.
Horváth, I., and Schmidtke, N. W. (1983). “Scale-up and scale-down concepts and problems.” Scale-up of Water and Wastewater Treatment Processes, Papers Presented at the 1st Int. Workshop, N. W. Schmidtke, and D. W. Smith, eds.,Butterworth, Boston, MA.
Huang, W., Yang, Q., and Xiao, H. (2009). “CFD modelling of scale effects on turbulence flow and scour around bridge piers.” Comput. Fluids, 38(5), 1050–1058.
Leopardi, M. (2004). “On roughness similarity of hydraulic models.” J. Hydraul. Res., 42(3), 239–245.
Levenspiel, O. (1999). Chemical reaction engineering, 3rd Ed., Wiley, New York.
Mitha, S. A., and Mohsen, M. F. N. (1990). “Scale effect on dispersion in chlorine contact chambers.” Can. J. Civ. Eng., 17(2), 156–165.
Rauen, W. B. (2001). “Effects of scale and discharge on the dynamic similitude and chlorine disinfection efficiency of scaled-down models of contact tanks.” M. Sc. dissertation, Dept. of Environmental Engineering, UFES, Brazil (in Portuguese).
Rauen, W. B. (2005). “Physical and numerical modelling of 3-D flow and mixing processes in contact tanks.” Ph.D. thesis, Cardiff Univ., Cardiff, U.K.
Rauen, W. B., Angeloudis, A., and Falconer, R. A. (2012). “Appraisal of chlorine contact tank modelling practices.” Water Res., 46(18), 5834–5847.
Rauen, W. B., Lin, B., Falconer, R. A., and Teixeira, E. C. (2008). “CFD and experimental model studies for water disinfection tanks with low Reynolds number flows.” Chem. Eng. J., 137(3), 550–560.
Roberson, J. A., and Crowe, C. T. (1993). Engineering fluid mechanics, 5th Ed., Houghton Mifflin, Boston.
Schmidtke, N. W., and Smith, D. W. (1983). “Introduction to scale-up of water and wastewater treatment processes.” Scale-up of Water and Wastewater Treatment Processes, Papers Presented at the 1st Int. Workshop, N. W. Schmidtke, and D. W. Smith, Butterworth, Boston, MA.
Shiono, K., and Teixeira, E. C. (2000). “Turbulence characteristics in a baffled contact tank.” J. Hydraul. Res., 38(4), 271–278.
Stamou, A. I. (2008). “Improving the hydraulic efficiency of water process tanks using CFD models.” Chem. Eng. Process. Process Intens., 47(8), 1179–1189.
Teixeira, E. C. (1993). “Hydrodynamic processes and hydraulic efficiency of chlorine contact units.” Ph.D. thesis, Univ. of Bradford, Bradford, U.K.
Teixeira, E. C., and Siqueira, R. N. (2008). “Performance assessment of hydraulic efficiency indexes.” J. Environ. Eng., 851–859.
Teixeira, E. C., Siqueira, R. C. N., and Rauen, W. B. (2002). “Automation of acquisition and processing of flow-through curves.” 5th Int. Conf. on Hydroinformatics, Cardiff, UK.
Tobis, J., and Vortmeyer, D. (1991). “Scale-up effects due to near-wall channelling in isothermal adsorption columns: On the limitations in the use of plug flow models.” Chem. Eng. Process. Process Intens., 29(3), 147–153.
Webb, C. B., Barfuss, S. L., and Johnson, M. C. (2010). “Modelling roughness in scale models.” J. Hydraul. Res., 48(2), 260–264.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Aug 30, 2012
Accepted: Aug 12, 2013
Published online: Aug 14, 2013
Published in print: Jan 1, 2014
Discussion open until: Jan 14, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.