Characterization of Bulk Fluid and Transport Properties for Simulating Polymer-Improved Aquifer Remediation
Publication: Journal of Environmental Engineering
Volume 139, Issue 2
Abstract
In situ mobility reduction resulting from the addition of water-soluble polymers to subsurface remedial fluid formulations has the potential to significantly improve the delivery and subsurface distribution of remediation agents within heterogeneous contaminated aquifer systems. However, the increased viscosity, non-Newtonian rheology, competing retention and acceleration mechanisms, and the potential for these fluids to reduce media permeability because of mechanical filtration of these large polymer molecules complicate treatment design calculations and often necessitate numerical simulation for purposeful evaluation and application of this technology. In this paper, laboratory and computational methods are presented that were used to characterize bulk fluid and porous media transport properties of xanthan gum biopolymer-amended fluids for the purpose of facilitating numerical simulation. A detailed discussion of polymerized fluid transport mechanisms and input parameters for simulating polymer transport using the University of Texas Chemical Composition (UTCHEM) simulator is provided. The simulator was used to validate the independently derived input parameters against the results of a five-layer, two-dimensional (2D) sand tank experiment. An overall 74% improvement in sweep efficiency was observed for the polymer-amended fluid within this sand pack, relative to the nonamended case.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for this work was provided by the U.S. Department of Defense, through the Strategic Environmental Remediation Defense Project (SERDP). The writers also acknowledge SERDP program manager Dr. Andrea Leeson for her assistance and guidance throughout this project.
References
Cadmus, M. C., Jackson, L. J., Burton, K. A., Plattner, R. D., and Slodki, M. E. (1982). “Biodegradation of xanthan gum by Bacillus sp.” Appl. Environ. Microbiol., 44(1), 5–11.
Cantrell, K. J., Kaplan, D. I., and Gilmore, T. J. (1997). “Injection of colloidal particles in sand with shear-thinning fluids.” J. Environ. Eng., 123(8), 786–791.
Center for Petroleum and Geosystems Engineering (CPGE). (2000a). UTCHEM 9.0: A three-dimensional chemical flood simulator. Volume I: User’s guide, Reservoir Engineering Research Program, Center for Petroleum and Geosystems Engineering, The Univ. of Texas at Austin, Austin, TX.
Center for Petroleum and Geosystems Engineering (CPGE). (2000b). UTCHEM 9.0: A three-dimensional chemical flood simulator. Volume II: Technical documentation, Reservoir Engineering Research Program, Center for Petroleum and Geosystems Engineering, The Univ. of Texas at Austin, Austin, TX.
Chauveteau, G., and Kohler, N. (1984). “Influence of microgels in polysaccharide solutions on their flow behavior through porous media.” Soc. Pet. Eng. J., 24(3), 361–368.
Chauveteau, G., and Lecourtier, J. (1988). “Propagation of polymer slugs through adsorbent porous media.” Water Soluble Polymers for Petroleum Recovery, G. A. Stahl, and D. N. Shultz, eds., Plenum, New York.
Chauveteau, G., and Zaitoun, A. (1981). “Basic rheological behavior of xanthan polysaccharide solution in porous media: Effects of pore size and polymer concentration.” Enhanced Oil Recovery: Proc., Third European Symp. on Enhanced Oil Recovery, F. J. Fayers, ed., Vol. 13, Elsevier, NY, 197–212.
CP Kelco. (2004). Kelzan®/Keltrol® xanthan gum book, 8th Ed., CP Kelco Company, Atlanta.
Dawson, R., and Lantz, R. B. (1972). “Inaccessible pore volume in polymer flooding.” Soc. Pet. Eng. J., 12(5), 448–452.
Delshad, M., Pope, G. A., and Sepehrnoori, K. (1996). “A compositional simulator for modeling surfactant enhanced aquifer remediation.” J. Contam. Hydrol., 23(4), 303–327.
Dominguez, J. G., and Willhite, G. P. (1977) “Retention and flow characteristics of polymer solutions in porous media.” Soc. Pet. Eng. J., 17(2), 111–121.
Fletcher, A. J. P., et al. (1991). “Measurements of polysaccharide polymer properties in porous media.” SPE 21018, Proc., of the SPE Int. Symp. on Oilfield Chemistry, Society of Petroleum Engineers, TX.
Giese, S. W., and Powers, S. E. (2002). “Using polymer solutions to enhance recovery of mobile coal tar and creosote DNAPLs.” J. Contam. Hydrol., 58(1–2), 147–167.
Hirisaki, G. J., and Pope, G. A. (1974). “Analysis of factors influencing mobility and adsorption in the flow of polymer solutions in porous media.” Soc. Pet. Eng. J., 14(4), 337–346.
Holzwarth, G., and Prestridge, E. B. (1977). “Multistranded helix in xanthan polysaccharide.” Sci., 197(4305), 757–759.
Lake, L. W. (1989). Enhanced oil recovery, Prentice Hall, Englewood Cliffs, NJ.
Littmann, W. (1988). Polymer flooding, Elsevier Science, New York.
Martel, K. E., Martel, R., Lefebvre, R., and Gélinas, P. J. (1998). “Laboratory study of polymer solutions used for mobility control during in situ NAPL recovery.” Ground Water Monit. Rem., 18(3), 103–113.
Martel, R., Hebert, A., Lefebvre, R., Gelinas, P., and Gabriel, U. (2004). “Displacement and sweep efficiencies in a DNAPL recovery test using micellar and polymer solutions injected in a five-spot pattern.” J. Contam. Hyd., 75(1–2), 1–29.
Meter, J. W., and Bird, R. B. (1964). “Tube flow of non-newtonian polymer solutions, Parts I and II—Laminar flow and rheological models.” AIChE J., 10(6), 878–881.
Oostrom, M., Wietsma, T. W., Covert, M. A., and Vermeul, V. R. (2007). “Zero-valent iron emplacement in permeable porous media using polymer additions.” Ground Water Monit. Rem., 27(1), 122–130.
Robert, T., Martel, R., Conrad, S. H., Lefebvre, R., and Gabriel, U. (2006). “Visualization of TCE recovery mechanisms using surfactant-polymer in a two-dimensional heterogenous sand model.” J. Contam. Hydrol., 86(1–2), 3–31.
Silva, J. A. K. (2011). “The utility of polymer amendment for enhancing in situ remediation effectiveness.” Ph.D. dissertation, Colorado School of Mines, Golden, CO.
Smith, F. W. (1970). “The behavior of partially hydrolyzed polyacrylamide solutions in porous media.” J. Pet. Technol., 22(2), 148–156.
Smith, M. M., Silva, J. A. K., Munakata-Marr, J., and McCray, J. E. (2008). “Compatibility of polymers and chemical oxidants for enhanced groundwater remediation.” Environ. Sci. Technol., 42(24), 9296–9301.
Sorbie, K. S. (1991). Polymer-improved oil recovery, CRC, Boca Raton, FL.
Truex, M. J., et al. (2011). “Injection of zero-valent iron into an unconfined aquifer using shear-thinning fluids.” Ground Water Monit. Rem., 31(1), 50–58.
Wyatt, N. B., and Liberatore, M. W. (2009). “Rheology and viscosity scaling of the polyelectrolyte xanthan gum.” J. Appl. Polym. Sci., 114(6), 4076–4084.
Wyatt, N. B., et al. (2002). “In situ remediation of coal tar-impacted soil by polymer-surfactant flooding.” Proc., of the Third Int. Conference on Remediation of Chlorinated and Recalcitrant Compounds, Battelle Press, OH.
Wyatt, N. B., Gunther, C. M., and Liberatore, M. W. (2011). “Increasing viscosity in entangled polyelectrolyte solutions by the addition of salt.” Soft Matter, 6(11), 3346–3352.
Young, C. M., Dwarakanath, V., and Malik, T. (2002). “In situ remediation of coal tar-impacted soil by polymer-surfactant flooding.” Proc., Third Int. Conf. of Chlorinated and Recalcitrant Compounds, Monterey, CA.
Zaitoun, A., and Kohler, N. (1987). “The role of adsorption in polymer propagation through reservoir rocks.” SPE 16274. Proc., SPE Int. Symp. on Oilfield Chemistry, Society of Petroleum Engineers, TX.
Zhong, L., Oostrom, M., Wietsma, T. W., and Covert, M. A. (2008). “Enhanced remedial delivery through fluid viscosity modifications: Experiments and numerical simulations.” J. Contam. Hydrol., 101(1–4), 29–41.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Dec 19, 2011
Accepted: Jun 27, 2012
Published online: Jan 15, 2013
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.