Effective and Safe Berming for Pavement Shoulder Maintenance in Cold Regions
Publication: Journal of Cold Regions Engineering
Volume 32, Issue 1
Abstract
Berming is a common nationwide practice in the United States for pavement shoulder maintenance, especially for states located in cold regions. Competent berming helps to improve the load support capacity of the pavement shoulder and prevent vehicle drop-off accidents. The durability of berm materials is compromised by snow plowing operations during the winter season. A nationwide survey of state departments of transportation shows that it is highly desirable to improve the effectiveness and safety during berming operations; compaction of berms is widely believed to improve their resistance to snow plowing, which will also lead to longer lasting berms. To evaluate the performance of alternative berm materials and compaction procedures, experimental studies were conducted on four common types of berm materials to evaluate the effects of compaction method (i.e., Proctor and vibratory compaction) and compaction energy. The experimental results indicate that vibratory compaction is effective for crushed limestone, but less effective for recycled asphalt pavement (RAP) material. Natural soil berm material is not well compacted by vibratory compaction. Heat treatment of RAP up to 60°C did not increase its interparticle adhesion. Sixteen trial sections that include combination of four types of berm compaction equipment and four types of berm materials were placed along two interstate highways routes. The berm compaction equipment studied include the berm monster, two-wheel vibratory roller, side-mounted roller, and pull-behind roller. Observations show that a side-mounted roller provides better compaction for both vertical edge and safety edge pavements. RAPs show a similar behavior under compaction as crushed limestone in the field. Tack coating significantly improves the stiffness of the berm and retains berm materials from erosion. Recommendations are provided to ensure effective and safe berm compaction, which will lead to longer-lasting berms to mitigate cold region pavement maintenance efforts.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study is supported by ODOT. Technical liaisons from ODOT include Tom Berning, Mark Bakle, and Craig Landefel. Jill Martindale is the project manager. The support and assistance from these organizations and individuals are highly appreciated.
References
AASHTO. (2001). Guidelines for geometric design of very low-volume roads, Washington, DC.
ASTM. (2006). “Standard test methods for maximum index density and unit weight of soils using a vibratory table.” ASTM D4253-00, West Conshohocken, PA.
ASTM. (2009). “Standard test methods for laboratory compaction characteristics of soil using standard effort.” ASTM D698-07, West Conshohocken, PA.
ASTM. (2012). “Standard test method for water content and density of soil in situ by time domain reflectometry (TDR).” ASTM D6780/D6780M-12, West Conshohocken, PA.
Bonte, D., Riley, R., and McDaniel, B. (2009). “Recycled asphalt pavement.” Indiana LTAP Asphalt Workshop, West Lafayette, IN.
Dillman, G. C. (1929). “Report of committee on maintenance.” Proc., 8th Annual Meeting of the Highway Research Board, Washington, DC.
Farris, J. B. (1975). “Roadbed stabilization-various methods, area bulletin.” Am. Railway Eng. Assoc., 76(651), 419–431.
Guo, Y., Li, J., Huang, Q., and Yu, X. (2015). “Experimental study of compaction behaviors and assessment of berm materials.” Innovative materials and design for sustainable transportation infrastructure, ASCE, Reston, VA.
Lamb, S. E. (1980). “Embankment stabilization by use of horizontal drains, embankment stabilization and soil mechanics.” Transp. Res. Rec., 749, 6–10.
Liu, Z., and Yu, X. (2012). “Time domain reflectometry sensor-assisted freeze/thaw analysis in geomaterials.” Cold Reg. Sci. Technol., 71, 84–89.
MATLAB version 15 [Computer software]. MathWorks, Natick, MA.
McLaughlin, R. (1966). “Operations and maintenance cost study.”, U.S. Bureau of Public Roads, Washington, DC.
MDOT (Michigan Department of Transportation). (2012). “Standard specifications for construction.” ⟨http://mdotcf.state.mi.us/public/design/englishstandardplans/⟩ (Feb. 14, 2014).
ODOT (Ohio Department of Transportation). (2013). “Construction and material specifications.” ⟨https://www.dot.state.oh.us/Divisions/ConstructionMgt/OnlineDocs/Pages/2013-Online-Spec-Book.aspx⟩ (Feb. 16, 2014).
PennDOT (Pennsylvania Department of Transportation). (2010). “Standards for roadway construction.” ⟨http://paconstructors.net/01LETDOCUMENTS/PENNDOT/GENERAL/070308widened_conc_paving.pdf⟩ (Feb. 16, 2014).
Souleyrette, R., McDonald, T., Hans, Z., Kamyab, A., Welch, T., and Storm, B. (2001). “Paved shoulders on primary highways in Iowa: An analysis of shoulder surfacing criteria, costs, and benefits.”, Center for Transportation Research and Education, Iowa State Univ., Ames, IA.
Van, D. W. (1922). “Berm maintenance.” Proc., 7th Annual Meeting of the Highway Research Board, Vol. 7, Washington, DC, 295–298.
White, D., Mekkawy, M., Jahren, C., Smith, D., and Suleiman, M. (2007). “Effective shoulder design and maintenance.”, Iowa State Univ., Ames, IA.
Yu, X., and Drnevich, V. P. (2004). “Soil water content and dry density by time domain reflectometry.” J. Geotech. Geoenviron. Eng., 922–944.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jan 28, 2016
Accepted: May 5, 2017
Published online: Sep 25, 2017
Discussion open until: Feb 25, 2018
Published in print: Mar 1, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.