Effect of Specifications Type on the Quality of Paving Contracts in New Brunswick
Publication: Journal of Construction Engineering and Management
Volume 135, Issue 9
Abstract
Construction specifications are used by transportation agencies to define the client’s requirements of the final product. The primary motivation of adopting the newer end result specification (ERS) or performance related specification over method-based specification (MBS) is to reduce clients’ costs, encourage contractors’ innovation, and improve overall quality. However, some transportation agencies have been reluctant to fully implement ERS due to lack of demonstrated evidence on whether they achieve comparable level of quality or performance. This paper investigates if the specification type has any effect on quality. The case study presented is based on data from New Brunswick Department of Transportation (NBDOT) from years 2003–2007. NBDOT generally uses ERSs to call paving contracts equal to or larger than 8,000 t. MBSs are used for all other smaller paving contracts. The most prevalent indicator variables for accepting asphalt paving jobs in North America [that is, percent theoretical maximum relative density, asphalt binder content, air voids, voids in mineral aggregates, percent passing 4.75 mm (No. 4), and (No. 200) sieves] were investigated. Statistical analysis was performed to compare the deviation of the quality indicator variables from their respective job mix formula values for paving projects that used MBS or ERS. ANOVA results revealed that there were no significant differences between the qualities achieved from the two specification types. Also, no significant differences were found from within-specification comparisons over the time frame examined. Given the possible cost advantages from agency’s point of view, the flexibility of the contractors to innovate and the fact that this study demonstrates quality is not compromised, there is an opportunity for agencies to expand or fully adopt the use of ERS specifications.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers thank New Brunswick Department of Transportation (NBDOT) for the data used in this paper. The writers especially acknowledge the efforts and willingness of Mr. Terry Hughes to assist in this research. The conclusions and opinions stated herein are exclusively the work and responsibility of the writers; they do not, in anyway, reflect the position of NBDOT.
References
ASCE. (1988). Manual of professional practice: Quality in the constructed project: A guideline for owners, designers and constructors, New York, 17–22.
Battikha, M. G., and Russell, A. D. (1998). “Construction quality management—Present and future.” Can. J. Civ. Eng., 25(3), 401–411.
Benson, P. E. (1995). “Comparison of end result and method specifications for managing quality.” Transp. Res. Rec., 1491, 3–10.
Benson, P. E. (1999). “Performance review of a quality control/quality assurance specification for asphalt concrete.” Transportation Research Record. 1654, Transportation Research Board, Washington, D.C., 88–94.
Burati, J. L., Weed, R. M., Hughes, C. S., and Hill, H. S. (2004). “Evaluation of procedures for quality assurance specifications.” Rep. No. FHWA-HRT-04–046, Federal Highway Administration, Washington, D.C.
FHWA. (2003). Major types of transportation construction specifications, Rep. Prepared for the AASHTO Highway Subcommittee on Construction Quality Construction Task Force, U.S. Dept. of Transportation—Federal Highway Administration, Washington, D.C.
Juran, J. M. (1989). “Juran on leadership for quality.” An executive handbook, Free Press, New York.
Kandhal, P. S., Cominsky, R. J., Maurer, D., and Motter, J. B. (1993). “Development and implementation of statistically based end-result specifications for hot-mix asphalt in Pennsylvania.” Transp. Res. Rec., 1389, 9–16.
NBDOT. (2006). “New Brunswick Department of Transportation standard specifications.” January 2006 electronic version, ⟨www.gnb.ca/0113/publications/2006_Standard_Specs-e.pdf⟩ (Nov. 07, 2007).
Pathomvanich, S., Najafi, F. T., Peter, A., and Kopac, P. A. (2002). “Procedure for monitoring and improving effectiveness of quality assurance specifications.” Transportation Research Record. 1813, Transportation Research Board, Washington D.C.
PMI. (2000). A guide to the project management body of knowledge, 2000 Ed., Project Management Institute, Newtown Square, Pa.
Rilett, L. R. (1998). “Identifying component variability of end product specification tests.” J. Constr. Eng. Manage., 124(2), 133–138.
Rogers, C., and Senior, S. (2007). “Experience with end-result specifications for granular base aggregates in Ontario.” Can. J. Civ. Eng., 34(9), 1169–1179.
Shewhart, W. A. (1939). Statistical method from the viewpoint of quality control, Dover, New York.
TRB. (1976). “Statistically oriented end-result specifications.” National Cooperative Highway Research Program Synthesis of Highway Practice No. 38, Transportation Research Board, Washington, D.C.
TRB. (1979). “Quality assurance.” National Cooperative Highway Research Program Synthesis of Highway Practice No. 65, Transportation Research Board, Washington, D.C.
TRB. (2002). “Glossary of highway quality assurance terms.” Transportation Research Record. E-C037, Transportation Research Board, Washington, D.C.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: May 28, 2008
Accepted: Mar 5, 2009
Published online: Aug 14, 2009
Published in print: Sep 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.