Fatigue Reliability Assessment of Potential Crack Initiation of Tube-to-Transverse Plate Connections for Cantilever Sign Support Structures
Publication: Journal of Performance of Constructed Facilities
Volume 32, Issue 2
Abstract
Tube-to-transverse plate stiffened connection details are widely used in cantilevered sign support structures in New Jersey and many other states. This stiffened fillet-welded connection showed a lower stress level than the socket connection at the fillet weld toe at the base. However, the tip of stiffener location on the tube wall becomes a more critical fatigue crack location according the AASHTO. This paper evaluates a reliability-based fatigue assessment for the potential crack initiation at the tip of stiffener. A synthetic analysis of 1-h averaged wind speed wind data from two New Jersey weather stations was performed. The wind data were transformed to the transient domain to represent the turbulent natural wind phenomena and the effective stress ranges and number of cycles were obtained using the rainflow counting technique. To evaluate fatigue resistance of these connection details, existing fatigue test data of fatigue crack initiation at the tip of stiffener were analyzed and a statistical analysis of linear stress-life () fatigue data provided fatigue coefficients. The probability of fatigue crack initiation versus time of sign structures with different orientations of sign panel was determined using a reliability-based fatigue assessment approach. Results showed that the probability of crack initiation during the life span is dependent on wind cycles, orientation, and fatigue coefficients obtained from experimental S–N curves. The results can be used to estimate inspection frequencies of this critical detail in sign structures.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2001). AASHTO standard specifications for structural supports for highway signs, luminaires, and traffic signals, Washington, DC.
AASHTO. (2009). AASHTO standard specifications for structural supports for highway signs, luminaires, and traffic signals, Washington, DC.
AASHTO. (2015). AASHTO LRFD specifications for structural supports for highway signs, luminaires, and traffic signals, Washington, DC.
ASCE. (2010). Minimum design loads for buildings and other structures, Reston, VA.
ASOS (Automated Surface Observation System). (1998). “Automated Surface Observation System users guide.” ⟨http://www.nws.noaa.gov/asos/pdfs/aum-toc.pdf⟩ (Dec. 6, 2017).
ASTM. (2007). “Standard practice of statistical analysis of linear or linearized stress-life (s-n) and strain-life (ϵ-N) fatigue data, annual book of ASTM standards.” ASTM E739-91, West Conshohocken, PA.
ASTM. (2011). “Standard practices for cycle counting in fatigue analysis, annual book of ASTM standards.” ASTM E1049-85, West Conshohocken, PA.
Ayyub, B. M., Assakkaf, I. A., Kihl, D. P., and Siev, M. W. (2002). “Reliability-based design guidelines for fatigue of ship structures.” Nav. Eng. J., 114(2), 113–138.
Dawood, M., Goyal, R., Dhonde, H., and Bradberry, T. (2014). “Fatigue life assessment of cracked high-mast illumination poles.” J. Perform. Constr. Facil., 311.
Diekfuss, J. A. (2013). “Reliability-based fatigue assessment of mast-arm sign support structures.” Ph.D. dissertation, Marquette Univ., Milwaukee.
Foley, C. M., and Diekfuss, J. A. (2016). “Reliability-based inspection protocols for mast-arm sign support structures.” J. Struct. Eng., 04016043.
Foley, C. M., Fournelle, R. A., Ginal, S. J., and Peronto, J. L. (2004). “Structural analysis of sign bridge structures and luminaire supports.”, Wisconsin DOT, Madison, WI.
Frangopol, D., Strauss, A., and Kim, S. (2008). “Bridge reliability assessment based on monitoring.” J. Bridge Eng., 258–270.
Gilani, A., and Whittaker, A. (2000). “Fatigue-life evaluation of steel post structures. I: Background and analysis.” J. Struct. Eng., 322–330.
Ginal, S. J. (2003). “Fatigue performance of full-span sign support structures considering truck-induced gust and natural wind pressures.” M.S. thesis, Marquette Univ., Milwaukee.
Kaczinski, M. R., Dexter, R. J., and Van Dien, J. P. (1998). “Fatigue-resistant design of cantilevered signal, sign and light supports.”, Transportation Research Board, National Research Council, Washington, DC, 2011.
Kaimal, J. C., Wyngaard, J. C., Izumi, Y., and Coté, O. R. (1972). “Spectral characteristics of surface-layer turbulence.” Q. J. R. Meteorol. Soc., 98(417), 563–589.
Kwon, K. (2011). “Reliability assessment, performance prediction and life-cycle management of fatigue sensitive structures based on field test data.” Ph.D. dissertation, Lehigh Univ., Bethlehem, PA.
MATLAB [Computer software]. MathWorks, Natick, MA.
Miner, M. A. (1945). “Cumulative damage in fatigue.” J. Appl. Mech., 12(3), 154–164.
NCDC (National Climatic Data Center). (2014). “National weather service automated surface observing system.” ⟨http://www.nws.noaa.gov/asos/⟩ (Dec. 6, 2017).
NJDOT (New Jersey Dept. of Transportation). (2007). General design criteria and standard drawings for overhead and cantilever sign support structures, Ewing Township, NJ.
Nowak, A. S., and Collins, K. R. (2000). Reliability of structures, McGraw-Hill, New York.
Roy, S., Park, Y. C., Sause, R., and Fisher, J. W. (2012). “Fatigue performance of stiffened tube-to-end plate socket connections in high-mast structures.” J. Struct. Eng., 1203–1213.
Roy, S., Park, Y. C., Sause, R., Fisher, J. W., and Kaufmann, E. K. (2011). “Cost effective details for sign, luminaires and signal structure.”, Transportation Research Board, National Research Council, Washington, DC.
Thompson, R. W. (2012). “Evaluation of high-level lighting poles subjected to fatigue loading.” M.S. thesis, Lehigh Univ., Bethlehem, PA.
Wirsching, P. H. (1984). “Fatigue reliability for offshore structure.” J. Struct. Eng., 2340–2356.
Information & Authors
Information
Published In
Journal of Performance of Constructed Facilities
Volume 32 • Issue 2 • April 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jun 16, 2017
Accepted: Sep 11, 2017
Published online: Jan 10, 2018
Published in print: Apr 1, 2018
Discussion open until: Jun 10, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.