Operational Modal Analysis and Rational Finite-Element Model Selection for Ten High-Rise Buildings based on On-Site Ambient Vibration Measurements
Publication: Journal of Performance of Constructed Facilities
Volume 31, Issue 5
Abstract
The frequencies and mode shapes of high-rise buildings obtained from on-site ambient vibration testing and operational modal analysis (OMA) are very important for dynamic structural analysis and seismic design. This paper introduces a high-rise building ambient vibration test project in Laibin. Some results obtained from full-scale measurements of the dynamic behavior of 10 high-rise buildings are described. Different pre- and postprocessing techniques were used for ambient vibration signal analysis, from which the modal parameters were obtained using three OMA techniques. By rationally analyzing and modeling the stiffness of the infill walls, six finite element (FE) models were built in PKPM and SAP2000 to estimate the analytical modal information. The influences of the infill wall mass and stiffness on the dynamic properties of a high-rise building are further discussed. According to the identified and calculated results, all three modes emerged in each modal dense region in the frequency domain of high-rise buildings. Finally, based on 25 proposed empirical equations, the fundamental periods of 10 buildings are calculated and summarized.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful for the support provided for this research by the National Key Research and Development Program of China (No. 2016YFC0701400), the NSFC (No. 51208190), the Hunan Provincial Natural Science Foundation of China (No. 12JJ4053), and the Research Fund for Chinese Doctoral Program of Higher Education (No. 20120161120028).
References
Allemang, R. J. (1999). “Vibrations: Analytical and experimental modal analysis.” Structural Dynamics Research Laboratory, Univ. of Cincinnati, Cincinnati.
ASCE. (2006). “Minimum design loads for buildings and other structures.”, Reston, VA.
Asmussen, J. C. (1997). “Modal analysis based on the random decrement technique—Application to civil engineering structures.” Ph.D. thesis, Univ. of Aalborg, Aalborg, Denmark.
Asteris, P. G., Antoniou, S. T., Sophianopoulos, D. S., and Chrysostomou, C. Z. (2011). “Mathematical macromodeling of infilled frames: State of the art.” J. Struct. Eng., 1508–1517.
Asteris, P. G., Cotsovos, D. M., Chrysostomou, C. Z., Mohebkhah, A., and Al-Chaar, G. K. (2013). “Mathematical micromodeling of infilled frames: State of the art.” Eng. Struct., 56, 1905–1921.
Baeza, M. (1963). “Natural periods of reinforced concrete buildings.” Engineering thesis, Dept. of Civil Engineering, Univ. of Chile, Santiago, Chile.
BIS (Bureau of Indian Standards). (1984). “Criteria for earthquake resistant design of structures.” New Delhi, India.
Brownjohn, J. M. (2003). “Ambient vibration studies for system identification of tall buildings.” Earthquake Eng. Struct. Dyn., 32(1), 71–95.
Brownjohn, J. M., and Pan, T. C. (2008). “Identifying loading and response mechanisms from ten years of performance monitoring of a tall building.” J. Perform. Constr. Facil., 24–34.
CEN (European Committee for Standardization). (2004). “Design of structures for earthquake resistance—Part 1.”, Brussels.
China Architectural and Building Press. (2001). “Code for seismic design of buildings.”, Beijing.
Chopra, A. K., and Goel, R. K. (2000). “Building period formulas for estimating seismic displacements.” Earthquake Spectra, 16(2), 533–536.
Ciloglu, K., Zhou, Y., Moon, F., and Aktan, A. (2012). “Impacts of epistemic uncertainty in operational modal analysis.” J. Eng. Mech., 1059–1070.
Cole, H. A. (1968). “On-the-line analysis of random vibrations.”, American Institute of Aeronautics and Astronautics, Reston, VA.
Crowley, H., and Pinho, R. (2006). “Simplified equations for estimating the period of vibration of existing buildings.” Proc., 1st European Conf. on Earthquake Engineering and Seismology, European Association for Earthquake Engineering (EAEE), Geneva.
Crowley, H., and Pinho, R. (2010). “Revisiting Eurocode 8 formulae for periods of vibration and their employment in linear seismic analysis.” Earthquake Eng. Struct. Dyn., 39(2), 223–235.
Fardis, M. N. (2009). Seismic design, assessment and retrofitting of concrete buildings: Based on EN-Eurocode 8, Springer, Dordrecht, Netherlands.
Gallipoli, M. R., et al. (2010). “Empirical estimates of dynamic parameters on a large set of European buildings.” Bull. Earthquake Eng., 8(3), 593–607.
Gilles, D. (2011). “In situ dynamic characteristics of reinforced concrete shear wall buildings.” Ph.D. thesis, Dept. of Civil Engineering and Applied Mechanics, McGill Univ., Montréal.
Goel, R. K., and Chopra, A. K. (1997). “Period formulas for moment-resisting frame buildings.” J. Struct. Eng., 1454–1461.
Guler, K., Yuksel, E., and Kocak, A. (2008). “Estimation of the fundamental vibration period of existing RC buildings in Turkey utilizing ambient vibration records.” J. Earthquake Eng., 12(S2), 140–150.
Hatzigeorgiou, G. D., and Kanapitsas, G. (2013). “Evaluation of fundamental period of low-rise and mid-rise reinforced concrete buildings.” Earthquake Eng. Struct. Dyn., 42(11), 1599–1616.
Holmes, M. (1961). “Steel frames with brickwork and concrete infilling.” Proc. Inst. Civ. Eng., 19(4), 473–478.
Hong, L. L., and Hwang, W. (2000). “Empirical formula for fundamental vibration periods of reinforced concrete buildings in Taiwan.” Earthquake Eng. Struct. Dyn., 29(3), 327–337.
Kijewski-Correa, T., et al. (2006). “Validating wind-induced response of tall buildings: Synopsis of the Chicago full-scale monitoring program.” J. Struct. Eng., 1509–1523.
Kose, M. M., and Karslioglu, O. (2009). “Effects of infills on high-rise buildings: A case study.” Struct. Des. Tall Spec. Build., 18(8), 907–920.
Li, Q. S., et al. (2006). “Wind tunnel and full-scale study of wind effects on China’s tallest building.” Eng. Struct., 28(12), 1745–1758.
Li, Q. S., Zhi, L., Tuan, A. Y., Kao, C., Su, S., and Wu, C. (2011). “Dynamic behavior of Taipei 101 tower: Field measurement and numerical analysis.” J. Struct. Eng., 143–155.
Mainstone, R. J. (1971). “On the stiffness and strength of infilled frames.” Proc. Inst. Civ. Eng., 49(2), 57–90.
Maison, B. F., and Neuss, C. F. (1985). “Dynamic analysis of a forty-four story building.” J. Struct. Eng., 1559–1572.
Michel, C., Guéguen, P., Lestuzzi, P., and Bard, P. (2010). “Comparison between seismic vulnerability models and experimental dynamic properties of existing buildings in France.” Bull. Earthquake Eng., 8(6), 1295–1307.
Midorikawa, S. (1990). “Ambient vibration tests of buildings in Santiago and Viña del Mar.”, Pontificia Universidad Catolica de Chile, Escula de Ingenieria, Departamento de Ingenieria Estructural, Santiago, Chile.
Navarro, M., et al. (2007). “Analysis of the weightiness of site effects on reinforced concrete (RC) building seismic behaviour: The Adra town example (SE Spain).” Earthquake Eng. Struct. Dyn., 36(10), 1363–1383.
NRCC (National Research Council of Canada). (1995). “The National Building Code.” Ottawa.
NRCC (National Research Council of Canada). (2005). “National Building Code of Canada.” Ottawa.
Pan, T. C., Goh, K. S., and Megawati, K. (2014). “Empirical relationships between natural vibration period and height of buildings in Singapore.” Earthquake Eng. Struct. Dyn., 43(3), 449–465.
Panzera, F., Lombardo, G., and Muzzetta, I. (2013). “Evaluation of building dynamic properties through in situ experimental techniques and 1D modeling: The example of Catania, Italy.” Phys. Chem. Earth Parts A/B/C, 63, 136–146.
Paulay, T., and Priestly, M. N. (1992). Seismic design of reinforced concrete and masonry buildings, Wiley, New York.
Peeters, B. (2000). “System identification and damage detection in civil engineering.” Ph.D. dissertation, Katholieke Univ., Leuven, Belgium.
Phillips, A. W., Allemang, R. J., and Fladung, W. A. (1998). “The complex mode indicator function (CMIF) as a parameter estimation method.” Proc., 16th Int. Modal Analysis Conf., Society for Experimental Mechanics, Bethel, CT, 705–710.
PKPM. [Computer software]. Weifang City, China, Geil Weifang Steel Works, Ltd.
Saneinejad, A., and Hobbs, B. (1995). “Inelastic design of infilled frames.” J. Struct. Eng., 634–650.
SAP2000. [Computer software]. CSI, Walnut Creek, CA.
Satake, N., Suda, K., Arakawa, T., Sasaki, A., and Tamura, Y. (2003). “Damping evaluation using full-scale data of buildings in Japan.” J. Struct. Eng., 470–477.
Shi, W., Shan, J., and Lu, X. (2012). “Modal identification of Shanghai World Financial Center both from free and ambient vibration response.” Eng. Struct., 36, 14–26.
Shih, C. Y., Tsuei, Y. G., Allemang, R. J., and Brown, D. L. (1989). “Complex mode indication function and its applications to spatial domain parameter estimation.” Proc., 7th Int. Modal Analysis Conf., Society for Experimental Mechanics, Bethel, CT, 533–540.
Smith, B. S., and Coull, A. (1991). Tall building structures: Analysis and design, Wiley, New York.
UBC (Uniform Building Code). (1970). “International Conf. of building officials.” Whittier, CA.
UBC (Uniform Building Code). (1997). “International Conf. of Building Officials.” Whittier, CA.
Xu, Y. L., Chen, S. W., and Zhang, R. C. (2003). “Modal identification of Di Wang building under Typhoon York using the Hilbert-Huang transform method.” Struct. Des. Tall Spec. Build., 12(1), 21–47.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jul 21, 2016
Accepted: Nov 29, 2016
Published online: Mar 17, 2017
Discussion open until: Aug 17, 2017
Published in print: Oct 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.