Foamed Concrete-Based Material as a Soft Ground Arresting System for Runways and Airfields
Publication: Journal of Performance of Constructed Facilities
Volume 30, Issue 1
Abstract
A soft ground arresting system (SGAS) is an alternative solution on airport runways where the runway safety area (RSA) does not meet international Federal Aviation Administration (FAA) standards. If an SGAS is installed on both ends of the runway, the length of the runway can be shortened. In this paper the options of using foamed concrete as the arresting bed material in an SGAS are investigated. Tests were conducted on the foamed concrete to determine whether it has the ability to withstand support vehicle loadings, while failing underneath loading from an overrunning aircraft. The objective of this paper is to present the required and measured properties of foamed concrete and results of an evaluation into its possible implementation as an SGAS as an alternative to engineered material arresting system (EMAS) on airports. The following conclusions are drawn. Foamed concrete properties allow it to be used as a possible arresting material, with the unit weight/density of foamed concrete the most important property to consider. The compressive strength and energy absorption of foamed concrete are two of the major properties allowing it to be used as an arresting material. Foamed concrete with densities of 600 and allowed for more settlement while the stress/deformation relationship was very similar to that of material currently used in arrestor beds. The large contact diameters of airport rescue firefighting (ARFF) vehicles’ tires allows them not to penetrate/destruct foamed concrete at densities as low as .
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work is based on research supported in part by the National Research Foundation of South Africa. The Grantholder acknowledges that opinions, findings, and conclusions or recommendations expressed in any publication generated by the NRF supported research are those of the authors, and that the NRF accepts no liability whatsoever in this regard.
References
ATSB. (2008). Runway excursions: Part 2, Australian Government, Canberra, Australia.
Bassani, M. S. E. C. F. (2012). “Performance prediction for innovative crushable material used in aircraft arrestor beds.” J. Mater. Civ. Eng., 725–734.
Boeing. (2009). “Statistical summary of commercial jet airplane accidents.” Boeing Commercial Airplanes, 〈http://www.airsafe.com/events/models/statsum2008.pdf〉 (Jan. 15, 2014).
Federal Aviation Administration (FAA). (1989). AC 150/5300-13-airport design, U.S. Dept. of Transportation, Washington, DC.
Federal Aviation Administration (FAA). (2012). Advisory circular 150/5220-22B, engineered materials arresting system (EMAS) for aircraft overrun, U.S. Dept. of Transportation, Washington, DC.
Fouad, H. (2006). “Cellular concrete.” Significance of tests and properties of concrete and concrete-making material, J. F. Lamond and J. H. Pielert, eds., ASTM International, West Conshohocken, PA.
Heymsfield, E. P. (2009). Performance prediction of the Strong Company’s soft ground arrestor system using a numerical analysis, Strong Company, Bridgeport, NJ.
Kearsley, E. P. (2005). “Designing mix composition of foamed concrete with high fly ash contents.” Proc., Int. Conf. on the Use of Foamed Concrete in Construction, Pine Bluff, Vol. I, 29–36.
Kearsley, E. P., and Mostert, H. F. (2005). “Designing mix composition of foamed concrete with high fly ash contents.” Proc., Int. Congress on Global Construction: Concrete Opportunities, Scotland, U.K., 29–36.
Legatski, L. A. (1987). “Structural considerations of cellular concrete.” Material and Member Behavior; Proc., Sessions at Structures Congress ‘87 Related to Materials and Member Behavior, ASCE, Reston, VA, 435–441.
Marisetty, S. C., Bailey, E. D., Hale, W. M., and Heymsfield, E. P. (2008). “Development of a soft ground arrestor system.” U.S. Dept. of Transportation, Fayetteville, AR.
National Transportation Safety Board (NTSB). (1998). “We are all safer.” NTSB-inspired improvements in transportation safety, 2nd Ed., Washington, DC.
Rosenbauer. (2011). “Rosenbauer USA.” 〈http://www.rosenbaueramerica.com/〉 (Mar. 17, 2013).
Santagata, E., Bassani, M., and Sacchi, E. (2010). “Performance of new materials for aircraft arrestor beds.” Transp. Res. Rec., 2177, 124–131.
Weights, E., and Agent, L. E. (2009). “STRIKER-1500 aircraft rescue and fire fighting vehicle specifications (standard configuration).” 〈http://www.oshkoshairport.com/〉 (Mar. 17, 2013).
Zodiac. (2013). “Zodiac aerospace.” 〈http://www.esco.zodiac.com/index.cfm?navid=73&cid=116〉 (Mar. 3, 2013).
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Feb 26, 2014
Accepted: Sep 26, 2014
Published online: Nov 6, 2014
Discussion open until: Apr 6, 2015
Published in print: Feb 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.