Remote Field Monitoring of Thermal and Moisture Deformations in Masonry Cavity Wall Building Envelopes
Publication: Journal of Performance of Constructed Facilities
Volume 29, Issue 3
Abstract
A clock tower in St. Albert, Alberta, Canada, was outfitted with a remote monitoring system to record the vertical deformations of its masonry cavity wall enclosures due to temperature and moisture changes. Monitoring the deformations of masonry wall enclosures is a unique application that is expected to provide new information on the causes of distress of brick veneers, which has traditionally been attributed to excessive expansion of the brick. Preliminary observations for clay brick veneer masonry suggest that reversible moisture-related strains could be significant and that radiation-induced temperature spikes could be much higher than what is accounted for by current design standards and codes. Most observed reversible moisture-induced strains were within the limits prescribed in the Canadian masonry standard and the national building code of Canada.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by the Natural Sciences and Engineering Research Council of Canada (NSERC) in collaboration with Read Jones Christoffersen (RJC). The city of St. Albert granted unlimited access to the tower. The authors acknowledge the contributions of G. Miller and C. West, Structural Laboratory technicians at the University of Alberta.
References
American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE). (2010). “Energy standard for buildings except low-rise residential buildings.”, Atlanta, GA.
ASTM. (2010). “Standard guide for calculating movement and other effects when establishing sealant joint width.”, West Conshohocken, PA.
Avallone, E. A., and Baumeister, T, III, eds. (1996). Marks’ standard handbook for mechanical engineers, 10th Ed., McGraw-Hill, New York.
Brick Industry Association (BIA). (2006). “Volume changes—Analysis and effects of movement.” Technical Note 18, Reston, VA.
Canadian Standards Association (CSA). (2004). “Design of masonry structures.”, Mississauga, ON, Canada.
Chalfoun, N. V. (2011). “Using energy simulation and real-time data monitoring to investigate thermal performance of exterior cavity walls.” Proc., 12th Conf. of Int. Building Performance Simulation Association, International Building Performance Simulation Association (IBPSA), Canberra, Australia, 1211–1216.
Chen, J. J., Thomas, J. J., and Jennings, H. M. (2006). “Decalcification shrinkage of cement paste.” Cem. Concr. Res., 36(5), 801–809.
Drysdale, R., and Khattab, M. (1995). “Shrinkage characteristics of concrete blocks.” Proc., 7th Canadian Masonry Symp., McMaster University, Hamilton, ON, Canada, 950–960.
Environment Canada. (2013). “Historical climate data.” 〈www.climate.weather.gc.ca〉 (Apr. 24, 2013).
European Committee for Standardization (CEN). (2005). “Eurocode 6: Design of masonry structures—Part 1: General—Rules for reinforced and unreinforced masonry.”, Brussels, Belgium.
Groves, G. W., Rodway, D. I., and Richardson, I. G. (1990). “The carbonation of hardened cement pastes.” Adv. Cem. Res., 3(11), 117–125.
Hatzinikolas, M. A., Elwi, A., Xie, J., and Peterson, A. (1995). “Thermal and material movements in cavity walls.” Proc., 4th Australasian Masonry Conf., Univ. of Technology, Sydney, NSW, Australia, 81–90.
Hubbs, B., and Hircock, M. (2003). “Building envelope performance monitoring.” Proc., 9th Canadian Conf. on Building Science and Technology, National Building Envelope Council Canada (NBEC), Ottawa, ON, Canada.
International Concrete Repair Institute (ICRI). (2008). “Guide for the evaluation of masonry façade structures.” Guideline No. 410.1-2008, Des Plaines, IL.
Jessop, E. (1980). “Moisture, thermal, elastic and creep properties of masonry: A state-of-the-art report.” Proc., 2nd Canadian Masonry Symp., Carleton Univ., Ottawa, ON, Canada, 505–520.
Kaye, G. W. C., and Laby, T. H., eds. (1995). Tables of physical and chemical constants, 16th Ed., Longman, New York.
Kuzik, M., Elwi, A. E., and Hatzinikolas, M. A. (1999). “Long term differential movements in masonry cavity walls.” Proc., 8th North American Masonry Conf., The Masonry Society (TMS), Boulder, CO, 12.
Masonry Standards Joint Committee (MSJC). (2011). “Building code requirements and specification for masonry structures.” The Masonry Society, Boulder, CO.
Maurenbrecher, A. H. P., Saïd, M. N. A., and Fontaine, L. (2003). “Monitoring non-structural performance of exterior masonry walls.”, National Research Council of Canada, Ottawa, ON, Canada.
Maurenbrecher, A. H. P., Saïd, M. N. A., Ibrahim, K., and Cornick, S. M. (2000). “Monitoring the performance of masonry building envelopes.” Proc., 12th Int. Brick/Block Masonry Conf., Polytechnic Univ. of Madrid, Madrid, Spain, 1221–1233.
Maurenbrecher, A. H. P., Shirtliffe, C. J., Rousseau, M. Z., and Saïd, M. N. A. (1998). “Monitoring the hygrothermal performance of a masonry wall with and without thermal insulation.” Proc., 8th Canadian Masonry Symp., Canadian Masonry Research Institute, Edmonton, AB, Canada.
Maurenbrecher, A. H. P., and Suter, G. T. (1989). “A loadbearing clay brick masonry deterioration problem: Monitoring temperature and moisture.” Proc., 5th Canadian Masonry Symp., Univ. of British Columbia, Vancouver, BC, Canada, 771–779.
Maurenbrecher, A. H. P., and Suter, G. T. (1993). “Frost damage to clay brick in a loadbearing masonry building.” Can. J. Civil Eng., 20(2), 247–253.
McLean, D. (1966). “The physics of high temperature creep in metals.” Rep. Prog. Phy., 29(1), 1–34.
Nabarro, F. R. N. (2004). “Do we have an acceptable model of power-law creep?” Mater. Sci. Eng. A, 387–389, 659–664.
National Concrete Masonry Association (NCMA). (2005). “Crack control in concrete masonry walls.” TEK 10-1A, Herndon, VA.
National Research Council of Canada (NRC). (2010). User’s guide—NBC 2010: Structural commentaries (Part 4 of Division B), Ottawa, ON.
Saito, H., ed. (1978). Physics and application of Invar alloys, Maruzen Company, Tokyo, Japan.
Straube, J., and Burnett, E. (2005). Building science for building enclosures, Building Science Press, Westford, MA.
Sydenham, P. H. (1973). “Nanometer stability of Invar and quartz suspended in catenary.” J. Phy. E: Sci. Instrum., 6(6), 572–576.
Thomasen, S. E., and Searls, C. L. (1990). “Assessment of building facades in masonry and stone.” STP 1098: Service life of rehabilitated buildings and other structures, S. J. Kelley and P. C. Marshall, eds., ASTM, Philadelphia, 108–116.
Uddin, M., et al. (2009). “Monitoring moisture levels in stone masonry using duff gauge sensors.” Proc., 4th Int. Conf. on Structural Health Monitoring on Intelligent Infrastructure (SHMII-4), International Society for Structural Health Monitoring of Intelligent Infrastructure (ISHMII), Winnipeg, MB, Canada, 8.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jul 13, 2013
Accepted: Nov 19, 2013
Published online: Aug 8, 2014
Discussion open until: Jan 8, 2015
Published in print: Jun 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.