Impact Resistance of Annealed Glass Panels
Publication: Journal of Performance of Constructed Facilities
Volume 25, Issue 5
Abstract
Annealed glass is by far the most commonly used glazing material in building construction. The resistant properties of glazing panels to wind loading has been studied for a long time based on quasistatic modeling. More recently, the vulnerability of infrastructure and its protection against acts of terrorism has been receiving a great deal of attention, as pioneered by the work of Wu and Hao from within Australia, whereas vulnerability studies by Stewart were specific to glass façades in terrorism scenarios. Emphasis has been on modeling the blast induced pressure and impulses, as they are applied to the panels while the resistant properties of the glazing materials have been based on assumptions used currently in design. Research undertaken by the writers over the past two to three years have revealed scopes of possible improvements to the current models that have been used in defining the resistant properties of glazing materials. Models based on the well known Weibull distribution, although widely assumed in practice, have been found to be not fully consistent with evidence produced experimentally or by analytical simulations. The interaction of the principal stresses surrounding the crack tip and higher mode effects have also been found to have significant effects on the ultimate behavior of the panel. The accurate modeling of these phenomena is particularly important for large panels. This paper provides an update of the redevelopment of a realistic behavioral model for annealed glazing panels subject to impact action. A new simulation procedure that takes various described phenomena into account is presented in this paper.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (2007). “Standard practice for determining load resistance of glass in buildings.” ASTM-E1300, West Conshohocken, PA.
Ayyub, B. M., and McCuen, R. H. (1997). Probability, statistics, and reliability for engineers, CRC Press, New York.
Beason, W. L. (1998). “Basis for ASTM E1300 annealed glass thickness selection charts.” J. Struct. Eng., 124(2), 215–221.
Beason, W. L., and Morgan, J. R. (1984). “Glass failure prediction model.” J. Struct. Eng., 110(2), 197–212.
Bogosian, D., Ferritto, J., and Shi, Y. (2002). “Measuring uncertainty and conservatism in simplified blast models.” 30th Explosives Safety Seminar, Department of Defense Explosives Safety Board.
Bouzid, S., Nyoungue, A., Azari, Z., Bouaouadja, N., and Pluvinage, G. (2001). “Fracture criterion for glass under impact loading.” Int. J. Impact Eng., 25(9), 831–845.
Brown, W. G. (1972). A load duration theory for glass design, National Research Council of Canada, Ottawa.
Calderone, I. (2000). “The equivalent wind loading for window glass design.” Ph.D. thesis, Monash Univ., Melbourne, Australia.
Calderone, I., and Jacob, L. (2001). “The fallacy of the Weibull distribution for window glass design.” Glass Processing Days, 293–297.
Christoforou, A. P., and Yigit, A. S. (1998). “Effect of flexibility on low velocity impact response.” J. Sound Vib., 217(3), 563–578.
Danzer, R. (2006). “Some notes on the correlation between fracture and defect statistics: Are Weibull statistics valid for very small specimens?” J. Eur. Ceram. Soc., 26(15), 3043–3049.
Danzer, R., Lube, T., and Supancic, P. (2001). “Monte Carlo simulations of strength distributions of brittle materials-type of distribution, specimen and sample size.” Z. Metallkd., 92(7), 773–783.
Fischer-Crips, A. C., and Collins, R. E. (1995). “Architectural glazing: Design standards and failure models.” Build. Environ., 30(1), 29–40.
Gilvarry, J. J. (1961). “Fracture of brittle solids: I. Distribution function for fragment size in single fracture (theoretical).” J. Appl. Phys., 32(3), 391–399.
Griffith, A. A. (1920). “The phenomena of rupture and flow in solids.” Philos. Trans. R. Soc. A, 221, 163–198.
Krohn, M. H. (2002). “Biaxial flexure strength and dynamic fatigue of soda lime silicate float glass.” J. Am. Ceram. Soc., 85(7), 1777–1781.
Lam, N. T. K., Gad, E. F., and Nurhuda, I. (2008). “Simple tools for analysing the dynamic impact behaviour of elastic beams and plates.” 20th Australian Conf. on the Mechanics of Structures and Materials, Univ. of Southern Queensland, Towoomba, Queensland, Australia, 737–742.
Lam, N. T. K., Tsang, H. H., and Gad, E. F. (2010). “Simulations of response to low velocity impact by spreadsheet.” International Journal of Structural Stability and Dynamics, 10(3), 483–499.
Lawn, B. R. (1993). Fracture of brittle solids, Cambridge University Press, NY.
Lemon, G. H. (1974). “A problem in the distribution of maximum flaw length after inspection.” Technometrics, 16(4), 577–583.
Nakano, M., Kishida, K., Yamauchi, Y., and Sogabe, Y. (1994). “Dynamic fracture initiation in brittle materials under combined mode I/II loading.” J. Phys. IV (France), 4, 695–700.
Nurhuda, I., Lam, N. T. K., Gad, E. F., and Calderone, I. (2010). “Estimation of strength in large annealed glass panels.” Int. J. Solids Struct., 47(18–19), 2591–2599.
Overend, M., Parke, G. A. R., and Buhagiar, D. (2007). “Predicting failure in glass—A general crack growth model.” J. Struct. Eng., 133(8), 1146–1155.
Pashah, S., Massenzio, M., and Jacquelin, E. (2008). “Prediction of structural response for low velocity impact.” Int. J. Impact Eng., 35(2), 119–132.
Porter, M. I., and Houlsby, G. T. (2001). “Development of crack size and limit state design methods for edge-abraded glass members.” Struct. Eng. Part A, 79(8), 29–35.
Priestley, M. J. N., Calvi, G. M., and Kowalsky, M. J. (2007). Displacement-based seismic design of structures, IUSS Press, Pavia, Italy.
Ravi-Chandar, K., and Knauss, W. G. (1984). “An experimental investigation into dynamic fracture: III. On steady-state crack propagation and crack branching.” Int. J. Fract., 26(2), 141–154.
Remennikov, A. M., and Rose, T. A. (2005). “Modelling blast loads on buildings in complex city geometries.” Comput. Struct., 83(27), 2197–2205.
Shim, V. P. M., Toh, S. L., and Quah, S. E. (1994). “Impact-induced flexural waves in a Timoshenko beam-shearographic detection and analysis.” Exp. Mech., 34(4), 340–348.
Smith, P. D., Rose, T. A., and Saotonglang, E. (1999). “Clearing blast waves from building facades.” Proc. Inst. Civ. Eng. Struct. Build., 134(2), 193–199.
Standards Australia. (2006). “Glass in building—Selection and installation.” AS1288, Sydney.
Stewart, M. G., and Netherton, M. D. (2005). “Blast reliability curves and uncertainty modelling for glazing subject to explosive blast loading.” 6th Asia Pacific Conf. on Shock and Impact Loads on Structures, Univ. of Western Australia, Perth, Western Australia, Australia, 523–530.
Stewart, M. G., and Netherton, M. D. (2008). “Security risks and probabilistic risk assessment of glazing subject to explosive blast loading.” Reliab. Eng. Syst. Saf., 93(x), 627–638.
Todinov, M. T. (2007). “An efficient algorithm for determining the risk of structural failure locally initiated by faults.” Prob. Eng. Mech., 22(1), 12–21.
United States Army. (1990). “Structures to resist the effects of accidental explosions.” TM5-1300US, Washington, DC.
Weibull, W. (1939). A statistical theory of the strength of materials, Generalstabens Litografiska Anstalts Förlag, Stockholm, Sweden.
Wu, C., and Hao, H. (2005). “Dynamic response and collapse analysis of structures to blast load.” 6th Asia-Pacific Conf. on Shock and Impact Loads on Structures, Univ. of Western Australia, Perth, Western Australia, Australia, 619–626.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Mar 17, 2010
Accepted: Oct 10, 2010
Published online: Oct 21, 2010
Published in print: Oct 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.