Explosion Performance of a Ball Powder Production Facility
Publication: Journal of Performance of Constructed Facilities
Volume 24, Issue 4
Abstract
A ball powder production facility recently experienced two subsequent explosions which occurred due to the detonation of 2,800 kg and 17,000 kg ball powder components in the mixer building and the temporary storage building, respectively. Consequently, three persons were killed; and these two structures were damaged heavily. In this study, the outline of the mixer building is explained as well as the details of explosion and the behavior of the structural system of the mixer building against explosion. The observed damage mechanism of the mixer building is explained through a nonlinear dynamic blast load analysis as well as the evaluation of the original design, in situ material characteristics, and construction details. Furthermore, the potential reasons of the second explosion in the temporary storage building and the effects of this explosion are discussed considering the separation and public route distances given in related standards.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Concrete Institute (ACI). (2008). “Building code requirements for structural concrete.” ACI 318-08, ACI Committee 318 and Commentary, Detroit.
ASCE. (1997). “Design of blast resistant buildings in petrochemical facilities, New York.
ASCE manual 42. (1985). “Design of structures to resist nuclear weapon effects.” New York.
Biggs, J. M. (1964). Introduction to structural dynamics, McGraw-Hill, New York.
Clough, R. W., and Penzien, J. (1993). Dynamics of structures, 3rd Ed., Computers and Structures, Inc, Berkeley, Calif.
Comité Euro-International du Béton (CEB). (1993). CEB-FIP model code 1990, Redwood Books, Wiltshire, U.K.
Department of Army. (1986). “Fundamentals of protective design for conventional weapons effects.” Technical manual TM5-855-1, Washington, D.C.
Department of Army, Navy, and Air Force. (1990). “Structures to resist the effects of accidental explosion.” Technical manual TM5-1300 (NAVFAC P-397, AFR 88-22), Washington, D.C.
Department of Defense. (1999). “DOD Ammunition and explosive safety standards.” DOD 6055.9-STD, Washington, D.C.
Department of Defense. (2003). “Minimum antiterrorism standards for buildings.” UFC 4-010-01, Washington, D.C.
Department of Defense. (2008). “Structures to resist the effects of accidental explosions.” UFC 3-340-02, Washington, D.C.
Department of Defense. (2009). “Design of buildings to resist progressive collapse.” UFC 4-023-03, Washington, D.C.
Department of Energy. (1992). “A manual for the prediction of blast and fragment loading on structures.” DOE/TIC-11628, Washington, D.C.
Diaz Alonso, F. D., Farradas, E. G., Perez, J. F. S., Aznar, A. M., Gimeno, J. R., and Alonso, J. M. (2006). “Characteristic overpressure-impulse-distance curves for the detonation of explosives, pyrotechnics or unstable substances.” J. Loss Prev. Process Ind., 19, 724–728.
Federal Emergency Management Agency. (1996). NONLIN Ver. 6. 01. users manuals I&II, Washington, D.C.
Ilki, A. (2000). “The nonlinear behavior of reinforced concrete members subjected to reversed cyclic loads.” Ph.D. thesis, Istanbul Technical Univ., Istanbul, Turkey (in Turkish).
Jones, J., Wu, C., Oehlers, D. J., Whittaker, A. S., Sun, W., Marks, S., and Coppala, R. (2009). “Finite difference analysis of simply supported RC slabs for blast loadings.” Eng. Struct., 31, 2825–2832.
Krauthammer, T. (2008). Modern protective structures, CRC, New York.
Krauthammer, T., Bazeos, N., and Holmquist, T. J. (1986). “Modified SDOF analysis of RC box-type structures.” J. Struct. Eng., 112(4), 726–744.
Krauthammer, T., Shahriar, S., and Shanaa, H. M. (1990). “Response of reinforced concrete elements to severe impulsive loads.” J. Struct. Eng., 116(4), 1061–1079.
Malvar, L. J., and Crawford, J. E. (1998). “Dynamic increase factors for steel reinforcing bars.” Proc., 28th DDESB Seminar.
Mander, J. B., Priestley, M. J. N., and Park, R. (1988). “Theoretical stress-strain model for confined concrete.” J. Struct. Div., 114(8), 1804–1826.
Mays, G. C., and Smith, P. D. (1995). Blast effects on buildings, Thomas Telford, London.
Moradi, L. G., Davidson, J. S., and Dinan, R. J. (2009). “Response of bonded membrane retrofit concrete masonry walls to dynamic pressure.” J. Perform. Constr. Facil., 23(2), 72–80.
Newmark, N. M. (1956). “An engineering approach to blast resistant design.” Trans. ASCE, 121, 45–64.
North Atlantic Treaty Organization (NATO). (2006). “Safety principles for the storage of military ammunition and explosives.” AASTP-1, Brussels, Belgium.
Pandey, A. K., Kumar, R., Paul, D. K., and Trikha, D. N. (2006). “Non-linear response of reinforced concrete containment structure under blast loading.” Nucl. Eng. Des., 236, 993–1002.
Remennikov, A. M. (2003). “A review of methods for predicting bomb blast effects on building.” Journal of Battlefield Technology, 6, 5–10.
Remennikov, A. M., and Rose, T. A. (2007). “Predicting the effectiveness of blast wall barriers using neural networks.” Int. J. Impact Eng., 34, 1907–1923.
U.S. Army Corps of Engineers. (2005). “Single degree of freedom blast effects design spreadsheets (SBEDS).” PDC TR-05-01, Washington, D.C.
U.S. Army Corps of Engineers. (2008). “Methodology manual for the single degree of freedom blast effects design spreadsheets.” PDC TR-06-01 Rev1, Washington, D.C.
Wharton, R. K., Formby, S. A., and Merrifield, R. (2000). “Air-blast TNT equivalence for a range of commercial blasting explosives.” J. Hazard. Mater., 79, 31–39.
Wu, C., Oehlers, D. J., and Day, I. (2009). “Layered blast capacity analysis of FRP retrofitted RC member.” Adv. Struct. Eng., 12, 435–449.
Yinon, Z., and Zitrin, S. (1996). Modern methods and applications in analysis of explosives, Wiley, New York.
Zhou, X. Q., and Hao, H. (2008). “Prediction of airblast loads on structures behind a protective barrier.” Int. J. Impact Eng., 35(5), 363–375.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Aug 18, 2009
Accepted: Dec 17, 2009
Published online: Dec 29, 2009
Published in print: Aug 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.