Multilayer versus Monolayer Externally Bonded CFRP Sheets for Shear Strengthening of Concrete T-Beams
Publication: Journal of Composites for Construction
Volume 25, Issue 4
Abstract
The use of externally bonded (EB) carbon fiber–reinforced polymer (CFRP) fabrics for strengthening existing structures has received worldwide acceptance since the late 1990s. The composites produced at the time were of low density and have established the experimental database used by codes and guidelines to develop their analytical design models. As for projects requiring higher densities, the design guidelines recommend the use of several plies (multilayers) of CFRP fabrics. Use of a multilayer fabric leads to higher installation costs. Therefore, the need for high-density CFRPs has been recognized over the last few years by manufacturers. However, outstanding issues remain to be investigated, such as (1) the maximum number of EB-CFRP layers that can be installed without exhibiting slippage or debonding, particularly on vertical surfaces where strengthening in shear is required; and (2) the effectiveness of shear strengthening with multilayer CFRP fabrics, taking into account premature debonding failure and the effect of CFRP thickness. This study aims to evaluate and compare experimentally the behavior of 18 full-size reinforced concrete (RC) T-beams strengthened in shear with multilayer CFRP sheets to that of beams with monolayer strengthening fabric of equivalent density. The influence of internal transverse steel reinforcement (steel stirrups) on EB-CFRP fabric performance is also examined. The test results revealed that the increase in CFRP weight enables an increase in shear resistance, but not in a proportional way, up to an optimal value (300 g/m2 in this study). In addition, strains in CFRP featured lower values as the number of layers increased and were more significant in monolayers than multilayers of equivalent weight. Finally, predictions of current design guidelines were closer to experimental results for beams without steel stirrups because they do not yet consider the interaction between EB-FRP and transverse steel.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support of the Natural Sciences and Engineering Research Council of Canada (NSERC) and the Fonds de Recherche du Québec—Nature et Technologie (FRQNT) through operating grants to Professor Chaallal is gratefully acknowledged. The authors thank Sika-Canada (Pointe-Claire, Quebec) for contributing to the cost of materials. The efficient collaboration of Jonathan Auger and John Lescelleur (senior technicians) at École de technologie supérieure (ÉTS) in conducting the tests is acknowledged.
References
ACI (American Concrete Institute). 2017. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. ACI 440.2R-17. Farmington Hills, MI: ACI.
Altin, S., O. Anil, Y. Kopraman, Ç. Mertoğlu, and M. E. Kara. 2010. “Improving shear capacity and ductility of shear-deficient RC beams using CFRP strips.” J. Reinf. Plast. Compos. 29 (19): 2975–2991. https://doi.org/10.1177/0731684410363182.
ASTM. 2018. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39/C39M-18. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard test methods and definitions for mechanical testing of steel products. ASTM A370-19. West Conshohocken, PA: ASTM.
Bousselham, A., and O. Chaallal. 2004. “Shear strengthening reinforced concrete beams with fiber-reinforced polymer: Assessment of influencing parameters and required research.” ACI Struct. J. 101 (2): 219–227.
Bousselham, A., and O. Chaallal. 2006. “Behavior of reinforced concrete T-beams strengthened in shear with carbon fiber–reinforced polymer: An experimental study.” ACI Struct. J. 103 (3): 339–347.
Bousselham, A., and O. Chaallal. 2008. “Mechanisms of shear resistance of concrete beams strengthened in shear with externally bonded FRP.” J. Compos. Constr. 12 (5): 499–512. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:5(499).
Chaallal, O., M.-J. Nollet, and D. Perraton. 1998. “Shear strengthening of RC beams by externally bonded side CFRP strips.” J. Compos. Constr. 2 (2): 111–113. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:2(111).
Chaallal, O., M. Shahawy, and M. Hassan. 2002. “Performance of reinforced concrete T-girders strengthened in shear with carbon fiber reinforced polymer fabric.” ACI Struct. J. 99 (3): 335–343.
Chalioris, C. E., A. G. Zapris, and C. G. Karayannis. 2020. “U-jacketing applications of fiber-reinforced polymers in reinforced concrete T-beams against shear—Tests and design.” Fibers 8 (2): 13. https://doi.org/10.3390/fib8020013.
CSA (Canadian Standard Association). 2012. Design and construction of building structures with fibre-reinforced polymers. CAN/CSA S806-12. Mississauga, ON, Canada: CSA.
CSA (Canadian Standard Association). 2019. Canadian highway bridge design code. CAN/CSA S6-19. Mississauga, ON, Canada: CSA.
Deniaud, C., and J. J. R. Cheng. 2001. “Review of shear design methods for reinforced concrete beams strengthened with fibre reinforced polymer sheets.” Can. J. Civ. Eng. 28 (2): 271–281. https://doi.org/10.1139/l00-113.
Diagana, C., A. Li, B. Gedalia, and Y. Delmas. 2003. “Shear strengthening effectiveness with CFRP strips.” Eng. Struct. 25: 507–516. https://doi.org/10.1016/S0141-0296(02)00208-0.
fib (International Federation for Structural Concrete). 2001. Externally bonded FRP reinforcement for RC structures. fib-TG9.3-01. Lausanne, Switzerland: fib.
Li, A., C. Diagana, and Y. Delmas. 2002. “Shear strengthening effect by bonded composite fabrics on RC beams.” Composites, Part B 33 (3): 225–239. https://doi.org/10.1016/S1359-8368(02)00003-3.
Li, W., Z. Huang, Z. Huang, X. Yang, T. Shi, and F. Xing. 2020. “Shear behavior of RC beams with corroded stirrups strengthened using FRP laminates: Effect of the shear span-to-depth ratio.” J. Compos. Constr. 24 (4): 04020033. https://doi.org/10.1061/(ASCE)CC.1943-5614.0001042.
Foster, R. M., M. Brindley, J. M. Lees, T. J. Ibell, C. T. Morley, A. P. Darby, and M. C. Evernden. 2017. “Experimental investigation of reinforced concrete T-beams strengthened in shear with externally bonded CFRP sheets.” J. Compos. Constr. 21 (2): 04016086. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000743.
Khalifa, A., W. J. Gold, A. Nanni, and A. Abdel. 1998. “Contribution of externally bonded FRP to shear capacity of RC flexural members.” J. Compos. Constr. 2 (4): 195–202. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:4(195).
Ma, S., N. Muhamad Bunnori, and K. K. Choong. 2020. “Experimental study on shear strengthening of reinforced concrete box beam by CFRP.” Iran. J. Sci. Technol. Trans. Civ. Eng. 44 (4): 1075–1085. https://doi.org/10.1007/s40996-020-00415-8.
Mofidi, A., and O. Chaallal. 2011. “Shear strengthening of RC beams with externally bonded FRP composites: Effect of strip-width-to-strip-spacing ratio.” J. Compos. Constr. 15 (5): 732–742. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000219.
Mofidi, A., and O. Chaallal. 2014. “Effect of steel stirrups on shear resistance gain due to externally bonded fiber-reinforced polymer strips and sheets.” ACI Struct. J. 111 (2): 353–361. https://doi.org/10.14359/51686527.
Monti, G., and M. A. Liotta. 2007. “Tests and design equations for FRP-strengthening in shear.” Constr. Build. Mater. 21 (4): 799–809. https://doi.org/10.1016/j.conbuildmat.2006.06.023.
Panda, K. C., S. K. Bhattacharyya, and S. V. Barai. 2013. “Effect of transverse steel on the performance of RC T-beams strengthened in shear zone with GFRP sheet.” Constr. Build. Mater. 41: 79–90. https://doi.org/10.1016/j.conbuildmat.2012.11.098.
Pellegrino, C., and C. Modena. 2002. “Fiber reinforced polymer shear strengthening of reinforced concrete beams with transverse steel reinforcement.” J. Compos. Constr. 6 (2): 104–111. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:2(104).
Saleem, M. U., N. Khurram, M. N. Amin, and K. Khan. 2018. “Finite element simulation of RC beams under flexure strengthened with different layouts of externally bonded fiber reinforced polymer (FRP) sheets.” Rev. Constr. 17 (3): 383–400. https://doi.org/10.7764/RDLC.17.2.383.
Sika Canada. n.d. Structural strengthening systems. Montreal, QC: Sika. Accessed April 13, 2021. https://can.sika.com/en/construction/concrete-repair-protection/structural-strengtheningsystems.html.
Täljsten, B. 2003. “Strengthening concrete beams for shear with CFRP sheets.” Constr. Build. Mater. 17 (1): 15–26. https://doi.org/10.1016/S0950-0618(02)00088-0.
Tetta, Z. C., L. N. Koutas, and D. A. Bournas. 2015. “Textile-reinforced mortar (TRM) versus fiber-reinforced polymers (FRP) in shear strengthening of concrete beams.” Composites, Part B 77: 338–348. https://doi.org/10.1016/j.compositesb.2015.03.055.
Triantafillou, T. C. 1998. “Shear strengthening of reinforced concrete beams using epoxy-bonded FRP composites.” ACI Struct. J. 95: 107–115.
Information & Authors
Information
Published In
Journal of Composites for Construction
Volume 25 • Issue 4 • August 2021
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Sep 10, 2020
Accepted: Mar 26, 2021
Published online: May 5, 2021
Published in print: Aug 1, 2021
Discussion open until: Oct 5, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.