Experimental Analysis of Shear Resisting Mechanisms in FRP RC Beams with Shear Reinforcement
Publication: Journal of Composites for Construction
Volume 24, Issue 5
Abstract
Owing to the unique mechanical characteristics and lack of plasticity of fiber-reinforced polymers (FRPs), relatively large strains can develop in FRP reinforced concrete (RC) elements at ultimate limit states and this can lead to different relative contributions of concrete and shear reinforcement to the total element's shear capacity. This paper examines the development and relative contribution of the main shear resisting mechanisms in concrete beams with different overall depths and reinforced with longitudinal and transversal FRP reinforcement. Complementary strain measurements obtained from digital image correlation (DIC) and strain gauges are presented and discussed thoroughly. Although current FRP shear design approaches rely on the assumption that the contributions of concrete and shear reinforcement are constant up to failure, their relative magnitude is found to vary with increasing crack width. The experimental results indicate that, when minimum shear reinforcement is provided, current shear models based on a fixed truss angle approach tend to overestimate the contribution of concrete and underestimate the contribution of shear reinforcement. The use of a variable angle truss model, along with an appropriate reduction in the contribution of concrete, would lead to a more reliable estimate of the main shear resisting mechanisms and optimal design of the required amount of shear reinforcement.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by the EU FP7 Marie Skłodowska–Curie Initial Training Network endure (Grant Agreement No. 607851). The authors would like to thank the European Commission for its financial support and for providing wide networking opportunities within the research community.
Notation
The following symbols are used in this paper:
- Afl
- total area of the longitudinal reinforcement;
- Afv
- total area of the shear reinforcement at given spacing;
- a
- length of the test shear span;
- a′
- length of the nontest shear span;
- bw
- width of the beam;
- d
- effective depth of the beam;
- dv
- effective shear depth of the beam;
- Ec
- modulus of elasticity of the concrete;
- Efl
- Young's modulus of longitudinal FRP reinforcement;
- Efv
- Young's modulus of shear FRP reinforcement;
- fFRPu
- ultimate strength of the shear link;
- concrete cylinder strength;
- ffb
- allowable strength of the bent portion of the FRP stirrup;
- ffu
- allowable stress in the shear reinforcement;
- Fsl,i
- experimental force developed in ith shear link;
- h
- overall depth of the beam;
- k1
- ratio between the shear load in the test shear span and applied load;
- km
- coefficient taking into account the effect of moment at section on shear strength;
- kr
- coefficient taking into account the effect of reinforcement rigidity on its shear strength;
- ks
- coefficient taking into account the effect of member size on its shear strength;
- L
- beam's clear span;
- Ma
- applied moment;
- Pult
- ultimate load applied;
- s
- spacing of the FRP shear links;
- Va
- applied shear force;
- Vc
- shear capacity provided by concrete;
- Vcon
- estimated experimental contribution of concrete;
- Vexp
- experimental shear capacity;
- Vf
- calculated shear strength provided by FRP shear links;
- Vs
- calculated shear strength provided by steel stirrups;
- Vscr
- experimental shear force in tested shear span at diagonal cracking;
- wmax,DIC
- maximum crack width measured through DIC;
- δscr
- deflection at Vscr, measured under the loading point;
- ɛl,max
- maximum strain in the main longitudinal reinforcement;
- ɛt,max,DIC
- maximum strain in the shear links measured through DIC;
- ɛt,max
- maximum strain in the shear links;
- ɛti
- experimental strain measured in ith shear link (measured through DIC or strain gauge);
- ɛx
- strain at beam middepth;
- θ
- angle of inclination of the principal diagonal compressive stresses;
- λ
- factor accounting for concrete density;
- ρfl
- longitudinal reinforcement ratio;
- ρfv
- vertical (shear) reinforcement ratio;
- φc
- resistance factor for concrete; and
- φf
- resistance factor for FRP reinforcement.
References
ACI (American Concrete Institute). 2015. Guide for the design and construction of concrete reinforced with FRP bars. Technical Committee Document No. 440.1R-15. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2017. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. Technical Committee Document No. 440.2R-17. Farmington Hills, MI: ACI.
Bazant, Z. P., and M. T. Kazemi. 1991. “Size effect on diagonal shear failure of beams without stirrups.” ACI Struct. J. 88 (3): 268–276.
BISE (British Institution of Structural Engineers). 1999. Interim guidance on the design of reinforced concrete structures using fiber composite reinforcement. London: BISE.
CEN (European Committee for Standardization). 2004. Eurocode 2: Design of concrete structures. Pat 1-1: General rules and rules for buildings. EN 1992-1-1. Brussels, Belgium: CEN.
Cholostiakow, S. 2018. “Size effect in shear critical FRP RC beams.” Ph.D. thesis, Dep. of Civil and Structural Engineering, Univ. of Sheffield.
Cholostiakow, S., M. Di Benedetti, M. Guadagnini, and E. Zappa. 2018a. “Size effect in FRP RC beams with and without shear reinforcement.” Spec. Publ. 327: 27.1–27.20.
Cholostiakow, S., M. Di Benedetti, K. Pilakoutas, and M. Guadagnini. 2018b. “Effect of beam depth on shear behaviour of FRP RC beams.” J. Compos. Constr. 23 (1): 04018075. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000914.
CNR (National Research Council). 2006. Guide for the design and construction of concrete structures reinforced with fiber-reinforced polymer bars. CNR-DT 203. Rome: CNR.
CSA (Canadian Standards Associations). 2012. Design and construction of building components with fibre-reinforced polymers. CAN/CSA S806-12. Rexdale, ON, Canada: CSA.
CSA (Canadian Standards Associations). 2014. Canadian highway bridge design code. CSA S6-14. Mississauga, ON, Canada: CSA.
Di Benedetti, M., S. Cholostiakow, H. Fergani, E. Zappa, A. Cigada, and M. Guadagnini. 2015. “3D-DIC for strain measurement in small scale GFRP RC specimens.” In Proc., 3rd Conf. on Smart Monitoring, Assessment and Rehabilitation of Civil Structures, 1–8. Canada: International Institute of FRP in Construction (IIFC).
Duranovic, N., K. Pilakoutas, and P. Waldron. 1997. “Tests on concrete beams reinforced with glass fibre reinforced plastic bars.” In Vol. 2 of Proc., 3rd Int. Symp. on Non-Metallic (FRP) Reinforcement for Concrete Structures, 479–486. Tokyo, Japan: Japan Concrete Institute.
El-Sayed, A. K., E. F. El-Salakawy, and B. Benmokrane. 2006. “Shear strength of FRP-reinforced concrete beams without transverse reinforcement.” ACI Struct. J. 103 (2): 235–243.
fib (Fédération internationale du béton). 2007. FRP reinforcement in RC structures. fib bulletin 40, Technical Rep. Lausanne, Switzerland: fib.
fib (Fédération internationale du béton). 2013. Fib model code for concrete structures 2010. London: Ernest & Sohn.
fib (Fédération internationale du béton). 2019. Externally applied FRP reinforcement for concrete structures. fib bulletin 90, Technical Rep. Lausanne, Switzerland: FIB.
Guadagnini, M., K. Pilakoutas, and P. Waldron. 2003. “Shear performance of FRP reinforced concrete beams.” J. Reinf. Plast. Compos. 22 (15): 1389–1407. https://doi.org/10.1177/073168403035579.
Guadagnini, M., K. Pilakoutas, and P. Waldron. 2006. “Shear resistance of FRP RC beams: Experimental study.” J. Compos. Constr. 10 (6): 464–473. https://doi.org/10.1061/(ASCE)1090-0268(2006)10:6(464).
Helal, Y., R. Garcia, K. Pilakoutas, M. Guadagnini, and I. Hajirasouliha. 2016. “Strengthening of short splices in RC beams using post-tensioned metal straps.” Mater. Struct. 49: 133–147. https://doi.org/10.1617/s11527-014-0481-6.
Hoult, N. A., E. G. Sherwood, E. C. Bentz, and M. P. Collins. 2008. “Does the use of FRP reinforcement change the one-way shear behavior of reinforced concrete slabs?” J. Compos. Constr. 12 (2): 125–133. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:2(125).
ISIS (Intelligent Sensing for Innovative Structures). 2007. Reinforcing concrete structures with fiber reinforced polymers. ISIS-M03-07. Winnipeg, MB, Canada: Univ. of Winnipeg.
ISO. 2008. Fibre-reinforced polymer (FRP) reinforcement of concrete—Test methods—Part 1: FRP bars and grids. ISO Standard No. 10406-1:2008. Geneva: ISO.
Issa, M. A., T. Ovitigala, and M. Ibrahim. 2015. “Shear behavior of basalt fiber reinforced concrete beams with and without basalt FRP stirrups.” J. Compos. Constr. 12 (2): 125–133. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000638.
Joint ACI-ASCE Committee 445. 1998. “Recent approaches to shear design of structural concrete.” J. Struct. Eng. 124 (12): 1375–1417. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:12(1375).
JSCE (Japan Society of Civil Engineers). 1997. “Recommendations for design and construction of concrete structures using continuous fibre reinforced materials.” In Research committee on continuous fibre reinforced materials. Concrete Engineering Series 23, edited by A. Machida. 18–25. Tokyo: JSCE.
Kani, G. 1967. “How safe are our large reinforced concrete beams?” ACI J. Proc. 64 (3): 128–141.
Khodaie, S., F. Matta, and M. Alnaggar. 2019. “Discrete meso-scale modeling and simulation of shear response of scaled glass FRP reinforced concrete beams without stirrups.” Eng. Fract. Mech. 216: 106486. https://doi.org/10.1016/j.engfracmech.2019.106486.
Kotsovos, M. D. 1988. “Compressive force path: Basis for ultimate limit state reinforced concrete design.” ACI Struct. J. 85 (1): 68–75.
Mikani, H., M. Katoh, H. Takeuchi, and T. Tamura. 1989. “Flexural and shear behaviour of RC beams reinforced with braided FRP rods in spiral shape.” Trans. Jpn. Concr. Inst. 11 (1): 119–206.
Mitchell, D., and M. P. Collins. 1974. “Diagonal compression field theory—A rational model for structural concrete in pure torsion.” ACI J. Proc. 71 (8): 396–408.
Muttoni, A., and M. Fernández Ruiz. 2008. “Shear strength of members without transverse reinforcement as function of critical shear crack width.” ACI Struct. J. 105 (2): 163–172.
Nagasaka, T., H. Fukuyama, and M. Tanigaki. 1993. “Shear performance of concrete beams reinforced with FRP stirrups.” In Proc., Int. Symp. on Fiber Reinforced-Plastic Reinforcement for Concrete Structures, edited by A. Nanni, and C. W. Dolan, 789–811. Detroit: American Concrete Institute.
Nielsen, M. P. 1984. Limit analysis and concrete plasticity. Englewood Cliffs, NJ: Prentice-Hall.
Razaqpur, A. G., B. O. Isgor, S. Greenaway, and A. Selley. 2004. “Concrete contribution to the shear resistance of fiber reinforced polymer reinforced concrete members.” J. Compos. Constr. 8 (5): 452–460. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:5(452).
Reineck, K. H. 1991. “Ultimate shear force of structural concrete members without transverse reinforcement derived from a mechanical model.” ACI Struct. J. 88 (5): 592–602.
Sabau, C., C. Popescu, G. Sas, T. Blanksvard, and B. Taljsten. 2018. “Axially loaded RC walls with cutout openings strengthened with FRCM composites.” J. Compos. Constr. 22 (6): 04018046. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000867.
Serbescu, A., M. Guadagnini, and K. Pilakoutas. 2015. “Mechanical characterization of basalt FRP rebars and long-term strength predictive model.” J. Compos. Constr. 19 (2): 04014037. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000497.
Shioya, T., M. Iguro, Y. Nojiri, H. Akiyama, and T. Okada. 1990. “Shear strength of large reinforced concrete beams.” Spec. Publ. 118: 259–280.
Stratford, T., and C. J. Burgoyne. 2003. “Shear analysis of concrete with brittle reinforcement.” J. Compos. Constr. 7 (4): 323–330. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:4(323).
Sutton, M. A., J. J. Orteu, and H. W. Schreier. 2009. Image correlation for shape, motion and deformation measurements—Basic concepts, theory and applications. New York: Springer Science + Business Media.
Tomlinson, D., and A. Fam. 2014. “Performance of concrete beams reinforced with basalt FRP for flexure and shear.” J. Compos. Constr. 19 (2): 04014036. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000491.
Tureyen, A. K., and R. J. Frosch. 2002. “Shear tests of FRP-reinforced concrete beams without stirrups.” Struct. J. 99 (4): 427–434.
Vecchio, F. J., and M. P. Collins. 1986. “The modified compression field theory for reinforced concrete elements subjected to shear.” ACI J. Proc. 83 (2): 219–231.
Yost, J. R., S. P. Gross, and D. W. Dinehart. 2001. “Shear strength of normal strength concrete beams reinforced with deformed GFRP bars.” J. Compos. Constr. 5 (4): 268–275. https://doi.org/10.1061/(ASCE)1090-0268(2001)5:4(268).
Zhou, P., and K. E. Goodson. 2001. “Subpixel displacement and deformation gradient measurement using digital image/speckle correlation.” Opt. Eng. 40 (8): 1613–1621. https://doi.org/10.1117/1.1387992.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Apr 9, 2019
Accepted: Mar 9, 2020
Published online: Jun 17, 2020
Published in print: Oct 1, 2020
Discussion open until: Nov 17, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.