Compressive Behavior of Brick Masonry Columns Confined with Steel-Reinforced Grout Jackets
Publication: Journal of Composites for Construction
Volume 23, Issue 5
Abstract
In this study, a new type of composite comprised of steel cords embedded in a mortar matrix—referred to as steel-reinforced grout (SRG)—is explored for use in the confinement of masonry columns. This paper presents the results of an experimental study carried out to understand the behavior of solid clay brick masonry columns confined by single-layer SRG jackets. Thirty-one confined and three unconfined columns with a square cross-section were tested to failure under a monotonic concentric compressive load. Test parameters considered were the SRG matrix type, column corner condition, and steel cord sheet density (i.e., steel cord spacing) in the SRG jacket. SRG confinement improved the compressive strength, ultimate strain, and energy absorption of masonry columns relative to the unconfined condition. Models from the literature for FRP-confined masonry were examined for their applicability to predict the strength increase from the SRG jacket, with certain models predicting the confined compressive strength within 9% of the test values.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Kerakoll S.p.A. of Sassuolo, Italy, is gratefully acknowledged for providing the composite materials in this study. SanMarco–Terreal Italia is gratefully acknowledged for providing the brick units. This work did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.
References
ACI (American Concrete Institute). 2010. Guide for the design and construction of externally bonded FRP system for strengthening unreinforced masonry structures. ACI 440.7R. Farmington Hills, MI: ACI.
Aiello, M. A., F. Micelli, and L. Valente. 2007. “Structural upgrading of masonry columns by using composite reinforcements.” J. Compos. Constr. 11 (6): 650–658. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:6(650).
Aiello, M. A., F. Micelli, and L. Valente. 2009. “FRP confinement of square masonry columns.” J. Comp. Constr. 13 (2): 148–158. https://doi.org/10.1061/(ASCE)1090-0268(2009)13:2(148).
Alabdulhady, M. Y., L. H. Sneed, and C. Carloni. 2017. “Torsional behavior of RC beams strengthened with PBO-FRCM composite: An experimental study.” Eng. Struct. 136: 393–405.
Alecci, V., F. Focacci, L. Rovero, G. Stipo, and M. De Stefano. 2016. “Extrados strengthening of brick masonry arches with PBO-FRCM composites: Experimental and analytical investigations.” Compos. Struct. 149 (1): 184–196. https://doi.org/10.1016/j.compstruct.2016.04.030.
ASTM. 2011. Standard test method for splitting tensile strength of cylindrical concrete specimens. ASTM C496. West Conshohocken, PA: ASTM.
ASTM. 2016a. Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM C109/C109M. West Conshohocken, PA: ASTM.
ASTM. 2016b. Standard test method for compressive strength of masonry prisms (using 2-in. or [50-mm] cube specimens). ASTM C1314. West Conshohocken, PA: ASTM.
Babaeidarabad, S., F. De Caso, and A. Nanni. 2013a. “URM walls strengthened with fabric-reinforced cementitious matrix composite subjected to diagonal compression.” J. Compos. Constr. 18 (2): 04013045. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000441.
Babaeidarabad, S., F. De Caso, and A. Nanni. 2013b. “Out-of-plane behavior of URM walls strengthened with fabric-reinforced cementitious matrix composite.” J. Compos. Constr. 18 (4): 04013057. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000457.
Bednarz, L., A. Gorski, J. Jasienko, and E. Rusinski. 2011. “Simulations and analyses of arched brick structures.” Autom. Constr. 20 (7): 741–754. https://doi.org/10.1016/j.autcon.2011.01.005.
Borri, A., G. Castori, and M. Corradi. 2011. “Masonry columns confined by steel fiber composite wraps.” Materials 4 (1): 311–326. https://doi.org/10.3390/ma4010311.
Campione, G., and N. Miraglia. 2003. “Strength and strain capacities of concrete compression members reinforced with FRP.” Cem. Concr. Compos. 25 (1): 31–41. https://doi.org/10.1016/S0958-9465(01)00048-8.
Carloni, C., C. Mazzotti, M. Savoia, and K. V. Subramaniam. 2015. “Confinement of masonry columns with FRCM composites.” Vol. 624 of Key engineering materials, 644–651. Zurich, Switzerland: Trans Tech Publications.
Cascardi, A., F. Longo, F. Micelli, and M. A. Aiello. 2017. “Compressive strength of confined column with fiber reinforced mortar (FRM): New design-oriented models.” Const. Build. Mater. 156 (Dec): 387–401. https://doi.org/10.1016/j.conbuildmat.2017.09.004.
CNR (Italian Council of Research). 2013. Guide for the design and construction of externally bonded FRP systems for strengthening existing structures. 200R1 CNR-DT. Rome: CNR.
Corradi, M., A. Borri, G. Castori, and R. Sisti. 2014. “Shear strengthening of wall panels through jacketing with cement mortar reinforced by GFRP grids.” Composites Part B 64 (Aug): 33–42. https://doi.org/10.1016/j.compositesb.2014.03.022.
Corradi, M., A. Grazini, and A. Borri. 2007. “Confinement of brick masonry columns with FRP materials.” Compos. Sci. Technol. 67 (9): 1772–1783. https://doi.org/10.1016/j.compscitech.2006.11.002.
D’Ambrisi, A., and F. Focacci. 2011. “Flexural strengthening of RC beams with cement-based composites.” J. Compos. Constr. 15 (5): 707–720. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000218.
De Santis, S., P. Casadei, G. De Canio, G. de Felice, M. Malena, M. Mongelli, and I. Roselli. 2016. “Seismic performance of masonry walls retrofitted with steel reinforced grout.” Earthquake Eng. Struct. Dyn. 45 (2): 229–251. https://doi.org/10.1002/eqe.2625.
De Santis, S., and G. de Felice. 2015. “Tensile behaviour of mortar-based composites for externally bonded reinforcement systems.” Composites Part B 68 (Jan): 401–413. https://doi.org/10.1016/j.compositesb.2014.09.011.
Di Ludovico, M., C. D’Ambra, A. Prota, and G. Manfredi. 2010. “FRP Confinement of tuff and clay brick columns: Experimental study and assessment of analytical models.” J. Compos. Constr. 14 (5): 583–596. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000113.
Fossetti, M., and G. Minafò. 2017. “Comparative experimental analysis on the compressive behaviour of masonry columns strengthened by FRP, BFRCM or steel wires.” Compos. Part B: Eng. 112 (Mar): 112–124. https://doi.org/10.1016/j.compositesb.2016.12.048.
Giamundo, V., G. P. Lignola, G. Maddaloni, A. Balsamo, A. Prota, and G. Manfredi. 2015. “Experimental investigation of the seismic performances of IMG reinforcement on curved masonry elements.” Composites Part B 70 (Mar): 53–63. https://doi.org/10.1016/j.compositesb.2014.10.039.
Giamundo, V., G. P. Lignola, G. Maddaloni, A. Prota, and G. Manfredi. 2016. “Shaking table tests on a full-scale unreinforced and IMG-retrofitted clay brick masonry barrel vault.” Bull. Earthquake Eng. 14 (6): 1663–1693. https://doi.org/10.1007/s10518-016-9886-7.
Hojdys, Ł., and P. Krajewski. 2015. “Laboratory tests on masonry vaults with backfill strengthened at the extrados.” In Vol. 624 of Key engineering materials, 510–517. Zurich, Switzerland: Trans Tech Publications.
Kerakoll S.p.A. 2017. “Kerakoll S.p.A.” Accessed February 1, 2017. www.kerakoll.com.
Krevaikas, T. D., and T. C. Triantafillou. 2005. “Masonry confinement with fibre-reinforced polymers.” J. Compos. Constr. 9 (2): 128–135. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:2(128).
Loreto, G., L. Leardini, D. Arboleda, and A. Nanni. 2013. “Performance of RC slab-type elements strengthened with fabric-reinforced cementitious-matrix composites.” J. Compos. Constr. 18 (3): A4013003. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000415.
Mezrea, P., I. Yilmaz, M. Ispir, E. Binbir, I. Bal, and A. Ilki. 2016. “External jacketing of unreinforced historical masonry piers with open-grid basalt-reinforced mortar.” J. Compos. Constr. 21 (3): 04016110. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000770.
Nanni, A. 2012. “A new tool for concrete and masonry repair.” Concr. Int. 34 (4): 43–49.
Ombres, L. 2012. “Debonding analysis of reinforced concrete beams strengthened with fibre reinforced cementitious mortar.” Eng. Fract. Mech. 81 (Feb): 94–109. https://doi.org/10.1016/j.engfracmech.2011.06.012.
Ombres, L. 2015. “Confinement effectiveness in eccentrically loaded masonry columns strengthened by fiber reinforced cementitious matrix (FRCM) jackets.” In Vol. 624 of Key engineering materials, 551–558. Zurich, Switzerland: Trans Tech Publications.
Papanicolaou, C. G., T. C. Triantafillou, K. Karlos, and M. Papathanasiou. 2007. “Textile-reinforced mortar (TRM) versus FRP as strengthening material of URM walls: In-plane cyclic loading.” Mater. Struct. 40 (10): 1081–1097. https://doi.org/10.1617/s11527-006-9207-8.
Pellegrino, C., and T. D’Antino. 2013. “Experimental behavior of existing precast prestressed reinforced concrete elements strengthened with cementitious composites.” Composites Part B 55 (Dec): 31–40. https://doi.org/10.1016/j.compositesb.2013.05.053.
Ramaglia, G., G. P. Lignola, A. Balsamo, A. Prota, and G. Manfredi. 2016. “Seismic strengthening of masonry vaults with abutments using textile-reinforced mortar.” J. Compos. Constr. 21 (2): 04016079. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000733.
Santandrea, M., G. Daissè, C. Mazzotti, and C. Carloni. 2017a. “An investigation of the debonding mechanism between FRCM composites and a masonry substrate.” In Vol. 747 of Key engineering materials, 382–389. Zurich, Switzerland: Trans Tech Publications.
Santandrea, M., G. Quartarone, C. Carloni, and X. Gu. 2017b. “Confinement of masonry columns with steel and basalt FRCM composites.” In Vol. 747 of Key engineering materials, 342–349. Zurich, Switzerland: Trans Tech Publications.
Sneed, L. H., C. Carloni, G. Baietti, and G. Fraioli. 2017. “Confinement of clay masonry columns with SRG.” In Vol. 747 of Key engineering materials, 350–357. Zurich, Switzerland: Trans Tech Publications.
Sneed, L. H., C. Carloni, G. Fraioli, and G. Baietti. 2018. “Confinement of brick masonry columns with SRG jackets.” ACI Spec. Publ. 324: 5.1–5.10.
Sneed, L. H., S. Verre, C. Carloni, and L. Ombres. 2016. “Flexural behavior of RC beams strengthened with steel-FRCM composite.” Eng. Struct. 127 (Nov): 686–699. https://doi.org/10.1016/j.engstruct.2016.09.006.
Toutanji, H., and Y. Deng. 2007. “Comparison between organic and inorganic matrices for RC beams strengthened with carbon fiber sheets.” J. Compos. Constr. 11 (5): 507–513. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:5(507).
UNI EN (Italian National Unification Agency). 2011. Methods of test for masonry units. Part 1: Determination of compressive strength. UNI EN 772-1. Milan, Italy: UNI EN.
Valluzzi, M. R., F. Daporto, E. Garbin, and M. Panizza. 2014. “Out-of-plane behavior of infill masonry panels strengthened with composite materials.” Mater. Struct. 47 (12): 2131–2145. https://doi.org/10.1617/s11527-014-0384-6.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jun 25, 2018
Accepted: Feb 15, 2019
Published online: Jul 25, 2019
Published in print: Oct 1, 2019
Discussion open until: Dec 25, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.