Effect of Sequential Exposure to UV Radiation and Water Vapor Condensation and Extreme Temperatures on the Mechanical Properties of GFRP Bars
Publication: Journal of Composites for Construction
Volume 22, Issue 1
Abstract
This paper presents test results carried out to investigate the mechanical properties of E-glass fiber-reinforced polymer (E-GFRP) bars with four different diameters (6, 8, 10, and 14 mm) after these bars were subjected to sequential exposure to ultraviolet (UV) radiation and water vapor condensation for different time periods (1,000, 2,000, and 3,000 h) and elevated temperatures (15–300°C). The mechanical properties of the GFRP bars were evaluated with tensile, flexural, short beam (shear), and low-cyclic fatigue tests conducted on 150 specimens after exposure conditions. A scanning electron microscope (SEM) was used to investigate the degradation mechanism of the bars subjected to UV radiation and water vapor condensation. The results showed that, generally, with increases in exposure time and temperature the mechanical properties of the bars decreased. UV radiation and water vapor condensation conditions did not show a significant effect on direct tensile tests, in comparison with flexural and short beam tests. Furthermore, GFRP bars lost up to 45% of their tensile strength at elevated temperatures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The support of Vatan Composites Company in the form of supplying materials and the support of Dr. Mohammad Hoseinpour Gollo in supplying test facilities in this research is greatly acknowledged.
References
ACI (American Concrete Institute). (2006). “Guide for the design and construction of concrete reinforced with FRP bars.” ACI 440.1R-06, Farmington Hills, MI.
Afshar, A., Alkhader, M., Korach, C. S., and Chiang, F.-P. (2015). “Effect of long-term exposure to marine environments on the flexural properties of carbon fiber vinylester composites.” Compos. Struct., 126(1), 72–77.
Alsayed, S., Al-Salloum, Y., Almusallam, T., El-Gamal, S., and Aqel, M. (2012). “Performance of glass fiber reinforced polymer bars under elevated temperatures.” Composites Part B, 43(5), 2265–2271.
Aniskevich, K., Aniskevich, A., Arnautov, A., and Jansons, J. (2012). “Mechanical properties of pultruded glass fiber-reinforced plastic after moistening.” Compos. Struct., 94(9), 2914–2919.
Ashrafi, H., Bazli, M., and Oskouei, A. V. (2017). “Enhancement of bond characteristics of ribbed-surface GFRP bars with concrete by using carbon fiber mat anchorage.” Constr. Build. Mater., 134(1), 507–519.
ASTM. (2014). “Standard test method for flexural properties of fiber reinforced pultruded plastic rods.” ASTM D4476/D4476M-14, West Conshohocken, PA.
ASTM. (2016a). “Standard practice for operating fluorescent ultraviolet (UV) lamp apparatus for exposure of nonmetallic materials.” ASTM G154-16, West Conshohocken, PA.
ASTM. (2016b). “Standard test method for apparent horizontal shear strength of pultruded reinforced plastic rods by the short-beam method.” ASTM D4475-02, West Conshohocken, PA.
ASTM. (2016c). “Standard test method for tensile properties of fiber reinforced polymer matrix composite bars.” ASTM D7205/D7205M-06, West Conshohocken, PA.
Bazli, M., Ashrafi, H., and Oskouei, A. V. (2016). “Effect of harsh environments on mechanical properties of GFRP pultruded profiles.” Composites Part B: Eng., 99(1), 203–215.
Bazli, M., Ashrafi, H., and Oskouei, A. V. (2017). “Experiments and probabilistic models of bond strength between GFRP bar and different types of concrete under aggressive environments.” Constr. Build. Mater., 148(1), 429–443.
Boinard, E., Pethrick, R. A., Dalzel-Job, J., and Macfarlane, C. J. (2000). “Influence of resin chemistry on water uptake and environmental ageing in glass fibre reinforced composites-polyester and vinyl ester laminates.” J. Mater. Sci., 35(8), 1931–1937.
Carra, G., and Carvelli, V. (2014). “Ageing of pultruded glass fibre reinforced polymer composites exposed to combined environmental agents.” Compos. Struct., 108(1), 1019–1026.
Carvelli, V., Pisani, M. A., and Poggi, C. (2013). “High temperature effects on concrete members reinforced with GFRP rebars.” Composites Part B, 54(1), 125–132.
Ceroni, F., Cosenza, E., Gaetano, M., and Pecce, M. (2006). “Durability issues of FRP rebars in reinforced concrete members.” Cem. Concr. Compos., 28(10), 857–868.
Chen, Y., Davalos, J. F., Ray, I., and Kim, H.-Y. (2007). “Accelerated aging tests for evaluations of durability performance of FRP reinforcing bars for concrete structures.” Compos. Struct., 78(1), 101–111.
Correia, J., Cabral-Fonseca, S., Branco, F., Ferreira, J., Eusébio, M., and Rodrigues, M. (2005). “Durability of glass fibre reinforced polyester (GFRP) pultruded profiles used in civil engineering applications.” Proc., 3rd Int. Conf. on Composites in Construction, Université Lyon I, Laboratoire Mécanique Matériaux et Structures, Lyon, France, 11–13.
CSA (Canadian Standard Association). (2002). “Design and construction of building components with fiber reinforced polymers.” CAN/CSA S806-02, Toronto.
Da Silva, L. V., da Silva, F. W., Tarpani, J. R., de Camargo Forte, M. M., and Amico, S. C. (2016). “Ageing effect on the tensile behavior of pultruded CFRP rods.” Mater. Des., 110(1), 245–254.
Del Prete, I., Bilotta, A., and Nigro, E. (2015). “Performances at high temperature of RC bridge decks strengthened with EBR-FRP.” Composites Part B, 68(1), 27–37.
Dong, Z., Wu, G., Xu, B., Wang, X., and Taerwe, L. (2016). “Bond durability of BFRP bars embedded in concrete under seawater conditions and the long-term bond strength prediction.” Mater. Des., 92(1), 552–562.
Feng, P., Wang, J., Wang, Y., Loughery, D., and Niu, D. (2014). “Effects of corrosive environments on properties of pultruded GFRP plates.” Composites Part B, 67(1), 427–433.
Fiore, V., Di Bella, G., and Valenza, A. (2011). “Glass-basalt/epoxy hybrid composites for marine applications.” Mater. Des., 32(4), 2091–2099.
Garcia-Espinel, J., Castro-Fresno, D., Gayo, P. P., and Ballester-Muñoz, F. (2015). “Effects of sea water environment on glass fiber reinforced plastic materials used for marine civil engineering constructions.” Mater. Des., 66(1), 46–50.
Gardoni, P., Der Kiureghian, A., and Mosalam, K. M. (2002). “Probabilistic capacity models and fragility estimates for reinforced concrete columns based on experimental observations.” J. Eng. Mech., 1024–1038.
Hoyos, C. G., and Vázquez, A. (2012). “Flexural properties loss of unidirectional epoxy/fique composites immersed in water and alkaline medium for construction application.” Composites Part B, 43(8), 3120–3130.
Jiang, X., Kolstein, H., and Bijlaard, F. S. (2013). “Moisture diffusion in glass-fiber-reinforced polymer composite bridge under hot/wet environment.” Composites Part B, 45(1), 407–416.
JSCE (Japan Society of Civil Engineers). (1997). Research committee on continuous fiber reinforcing materials, Tokyo.
Karbhari, V., et al. (2003). “Durability gap analysis for fiber-reinforced polymer composites in civil infrastructure.” J. Compos. Constr., 238–247.
Kodur, V., and Bisby, L. A. (2005). “Evaluation of fire endurance of concrete slabs reinforced with fiber-reinforced polymer bars.” J. Struct. Eng., 34–43.
Kumahara, S., Masuda, Y., Tanano, H., and Shimizu, A. (1993). “Tensile strength of continuous fiber bar under high temperature.” Spec. Publ., 138, 731–742.
Kumar, B. G., Singh, R. P., and Nakamura, T. (2002). “Degradation of carbon fiber-reinforced epoxy composites by ultraviolet radiation and condensation.” J. Compos. Mater., 36(24), 2713–2733.
Liau, W., and Tseng, F. (1998). “The effect of long-term ultraviolet light irradiation on polymer matrix composites.” Polym. Compos., 19(4), 440–445.
Lu, Z., Xian, G., and Li, H. (2015). “Effects of exposure to elevated temperatures and subsequent immersion in water or alkaline solution on the mechanical properties of pultruded BFRP plates.” Composites Part B, 77(1), 421–430.
Mahsuli, M., and Haukaas, T. (2012). “Computer program for multimodel reliability and optimization analysis.” J. Comput. Civ. Eng., 87–98.
Marais, S., Metayer, M., Nguyen, T. Q., Labbe, M., and Saiter, J. M. (2000). “Diffusion and permeation of water through unsaturated polyester resins—Influence of resin curing.” Eur. Polym. J., 36(3), 453–462.
Marouani, S., Curtil, L., and Hamelin, P. (2012). “Ageing of carbon/epoxy and carbon/vinylester composites used in the reinforcement and/or the repair of civil engineering structures.” Composites Part B, 43(4), 2020–2030.
Mouzakis, D. E., Zoga, H., and Galiotis, C. (2008). “Accelerated environmental ageing study of polyester/glass fiber reinforced composites (GFRPCs).” Composites Part B, 39(3), 467–475.
Nishizaki, I., and Meiarashi, S. (2002). “Long-term deterioration of GFRP in water and moist environment.” J. Compos. Constr., 21–27.
Papanicolaou, G., Kosmidou, T. V., Vatalis, A., and Delides, C. (2006). “Water absorption mechanism and some anomalous effects on the mechanical and viscoelastic behavior of an epoxy system.” J. Appl. Polym. Sci., 99(4), 1328–1339.
Poodts, E., Minak, G., and Zucchelli, A. (2013). “Impact of sea-water on the quasi static and fatigue flexural properties of GFRP.” Compos. Struct., 97(1), 222–230.
Robert, M., and Benmokrane, B. (2010). “Behavior of GFRP reinforcing bars subjected to extreme temperatures.” J. Compos. Constr., 353–360.
RT Software [Computer software]. RT Software ltd., London.
Sawpan, M. A., Mamun, A. A., and Holdsworth, P. G. (2014). “Long term durability of pultruded polymer composite rebar in concrete environment.” Mater. Des., 57(1), 616–624.
Schaff, J. R. (2001). Fatigue and life prediction, ASM handbook Vol. 21 composites, ASM International, Material Park, OH, 252–258.
Segovia, F., Ferrer, C., Salvador, M. D., and Amigo, V. (2000). “Influence of processing variables on mechanical characteristics of sunlight aged polyester-glass fibre composites.” Polym. Degrad. Stab., 71(1), 179–184.
Shin, K.-B., Kim, C.-G., Hong, C.-S., and Lee, H.-H. (2000). “Prediction of failure thermal cycles in graphite/epoxy composite materials under simulated low earth orbit environments.” Composites Part B, 31(3), 223–235.
Sousa, J., Correia, J., and Cabral-Fonseca, S. (2016). “Durability of glass fibre reinforced polymer pultruded profiles: Comparison between QUV accelerated exposure and natural weathering in a Mediterranean climate.” Exp. Tech., 40(1), 207–219.
Tomosawa, F., Nakatsuji, T., Kimura, K., Saka, K., and Kawaguchi, H. (1998). “Evaluation of ACM reinforcement durability by exposure test.” Proc., 17th Int. Conf. on Offshore Mechanics and Arctic Engineering, ASME, New York, 9.
Wang, X. L., and Zha, X. X. (2011). “Experimental research on mechanical behavior of GFRP bars under high temperature.” Proc., Applied Mechanics and Materials, Vol. 71, Trans Tech Publications, Switzerland, 3591–3594.
Wang, Y. C., Wong, P., and Kodur, V. (2007). “An experimental study of the mechanical properties of fibre reinforced polymer (FRP) and steel reinforcing bars at elevated temperatures.” Compos. Struct., 80(1), 131–140.
Zafar, A., Bertocco, F., Schjødt-Thomsen, J., and Rauhe, J. (2012). “Investigation of the long term effects of moisture on carbon fibre and epoxy matrix composites.” Compos. Sci. Technol., 72(6), 656–666.
Zainuddin, S., Hosur, M., Barua, R., Kumar, A., and Jeelani, S. (2010). “Effects of ultraviolet radiation and condensation on static and dynamic compression behavior of neat and nanoclay infused epoxy/glass composites.” J. Compos. Mater., 45(18), 1901–1918.
Zhou, J., and Lucas, J. P. (1999a). “Hygrothermal effects of epoxy resin. I: The nature of water in epoxy.” Polymer, 40(20), 5505–5512.
Zhou, J., and Lucas, J. P. (1999b). “Hygrothermal effects of epoxy resin. II: Variations of glass transition temperature.” Polymer, 40(20), 5513–5522.
Information & Authors
Information
Published In
Journal of Composites for Construction
Volume 22 • Issue 1 • February 2018
Copyright
©2017 American Society of Civil Engineers.
History
Received: Nov 25, 2016
Accepted: Sep 11, 2017
Published online: Dec 4, 2017
Published in print: Feb 1, 2018
Discussion open until: May 4, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.