Experimental Studies on Strength and Stiffness Enhancement in CFRP-Strengthened Structural Steel Channel Sections under Flexure
Publication: Journal of Composites for Construction
Volume 20, Issue 6
Abstract
An experimental study to investigate the stiffness and strength enhancement in a structural steel channel section strengthened by six different carbon fiber–reinforced polymer (CFRP) wrapping configurations is described in this paper. An approach of transforming the singly symmetric open section such as a channel section to a closed section by CFRP wrapping as a means to increase the stiffness and strength is demonstrated. A total of 21 specimens, both CFRP reinforced and bare steel specimens, were tested in four-point bending. Two different CFRPs, unidirectional and bidirectional fabrics, were used in wrapping the specimen. While the unidirectional layers contribute to the stiffness and strength, the bidirectional layer primarily contributes to confining the former in addition to increasing the resistance to lateral torsional buckling (LTB) of the specimens. The results indicate that the CFRP-strengthened closed sections confined by bidirectional fabrics are effective in enhancing the strength and stiffness compared to CFRP skin–strengthened sections (perimeter of bare steel channel sections overlayed with CFRP). The effectiveness of the closed section can be further improved by increasing the unidirectional CFRP layers prior to the final wrapping by bidirectional fibers. The variation in stiffness for all the CFRP configurations from the initial loading of specimens up to the ultimate is also investigated. This paper demonstrates that the strength and stiffness of steel channel sections can be significantly enhanced by means of appropriate CFRP wrapping configuration.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The second author would like to thank Uday B. Desai, Director, IIT Hyderabad, for providing funding through a seed grant that made this research possible.
References
ACI (American Concrete Institute). (2008). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.”, Farmington Hills, MI.
Bakht, B., et al. (2000). “Canadian bridge design code provisions for fiber-reinforced structures.” J. Compos. Constr, 3–15.
Bakis, C., et al. (2002). “Fiber-reinforced polymer composites for construction—State-of-the-art review.” J. Compos. Constr, 73–87.
Deng, K., Pan, P., Nie, X., Xu, X., Feng, P., and Ye, L. (2015). “Study of GFRP steel buckling restraint braces.” J. Compos. Constr, 04015009.
Dusicka, P., and Tinker, J. (2013). “Global restraint in ultra-lightweight buckling-restrained braces.” J. Compos. Constr, 139–150.
Ekiz, E., and El-Tawil, S. (2008). “Restraining steel brace buckling using a carbon fiber-reinforced polymer composite system: Experiments and computational simulation.” J. Compos. Constr, 562–569.
El-Tawil, S., and Ekiz, E. (2009). “Inhibiting steel brace buckling using carbon fiber-reinforced polymers: Large-scale tests.” J. Struct. Eng, 530–538.
Feng, P., Zhang, Y., Bai, Y., and Ye, L. (2013a). “Combination of bamboo filling and FRP wrapping to strengthen steel members in compression.” J. Compos. Constr, 347–356.
Feng, P., Zhang, Y., Bai, Y., and Ye, L. (2013b). “Strengthening of steel members in compression by mortar-filled FRP tubes.” Thin-Walled Struct., 64(1), 1–12.
Gao, X. Y., Balendra, T., and Koh, C. G. (2013). “Buckling strength of slender circular tubular steel braces strengthened by CFRP.” Eng. Struct., 46(1), 547–556.
Haedir, J., Bambach, M. R., Zhao, X. L., and Grzebieta, R. H. (2006). “Bending strength of CFRP strengthened circular hollow steel sections.” 3rd Int. Conf. on FRP Composites in Civil Engineering, Florida International Univ., Miami, 701–704.
Haedir, J., Bambach, M. R., Zhao, X. L., and Grzebieta, R. H. (2009). “Strength of circular hollow sections (CHS) tubular beams externally reinforced by carbon FRP sheets in pure bending.” Thin-Walled Struct., 47(10), 1136–1147.
Haedir, J., and Zhao, X. L. (2012). “Design of CFRP-strengthened steel CHS tubular beams.” J. Constr. Steel Res., 72, 203–218.
Haedir, J., Zhao, X. L., Bambach, M. R., and Grzebieta, R. H. (2010). “Analysis of CFRP externally-reinforced steel CHS tubular beams.” Compos. Struct., 92(12), 2992–3001.
Haedir, J., Zhao, X. L., Grzebieta, R. H., and Bambach, M. R. (2011). “Non-linear analysis to predict the moment-curvature response of CFRP-strengthened steel CHS tubular beams.” Thin-Walled Struct., 49(8), 997–1006.
Hollaway, L. C., and Teng, J. G. (2008). Strengthening and rehabilitation of civil infrastructures using fibre-reinforced polymer (FRP) composites, Woodhead, Cambridge, U.K.
ISMC (Indian Standard Medium weight Channel). (1989). “Dimensions for hot rolled steel beam, column, channel and angle sections.” IS 808, Bureau of Indian Standards, New Delhi, India.
Madhavan, M., Sanap, V., Verma, R., and Selvaraj, S. (2015). “Flexural strengthening of structural steel angle sections using CFRP: Experimental investigation.” J. Compos. Constr., 04015018.
Mertz, D., and Gillespie, J. (1996). “Rehabilitation of steel bridge girders through the application of advanced composite material.”, Transportation Research Board, Washington, DC.
Ritchie, A., Fam, A., and MacDougall, C. (2015). “Strengthening long steel columns of S-sections against global buckling around weak axis using CFRP plates of various moduli.” J. Compos. Constr, 04014074.
Schnerch, D., Dawood, M., Rizkalla, S., and Sumner, E. (2007). “Proposed design guidelines for strengthening of steel bridges with FRP materials.” Constr. Build. Mater., 21(5), 1001–1010.
Sen, R., and Liby, L. (1994). “Repair of steel composite bridge sections using carbon fiber reinforced plastic laminates.”, Florida Dept. of Transportation, Tallahassee, FL.
Teng, J. G., Yu, T., and Fernando, D. (2012). “Strengthening of steel structures with fiber reinforced polymer composites.” J. Constr. Steel Res., 78(11), 131–143.
Wu, G., Wang, H., Wu, Z., Liu, H., and Ren, Y. (2012). “Experimental study on the fatigue behavior of steel beams strengthened with different fiber-reinforced composite plates.” J. Compos. Constr, 127–137.
Zhao, X. L., and Zhang, L. (2007). “State of the art review on FRP strengthened steel structures.” Eng. Struct., 29(8), 1808–1823.
Information & Authors
Information
Published In
Journal of Composites for Construction
Volume 20 • Issue 6 • December 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Oct 28, 2015
Accepted: Feb 4, 2016
Published online: Apr 19, 2016
Discussion open until: Sep 19, 2016
Published in print: Dec 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.