Modulus Effect of Bonded CFRP Laminates Used for Repairing Preyield and Postyield Cracked Concrete Beams
Publication: Journal of Composites for Construction
Volume 18, Issue 4
Abstract
Two different prerepair loading histories were simulated in reinforced concrete beams, namely cracking within the elastic range, and overloading in the plastic range. After unloading, the beams were repaired with either high or ultrahigh modulus (210 or 400 GPa) carbon fiber–reinforced polymer (CFRP) plates, or a hybrid system, and then reloaded to failure. It was shown that the level of preexisting damage has insignificant effect on strengthening effectiveness and failure mode at ultimate. The 210 and 400 GPa CFRP of reinforcement ratio increased the yielding load by 33 and 60%, respectively, whereas the ultimate strength was increased by up to 29 and 51%, respectively. Doubling of the 400 GPa CFRP to 0.34% resulted in a 63% overall gain in flexural strength, which is only an 8% increase over , because of change in failure mode from rupture to concrete cover delamination. The beam retrofitted by hybrid CFRP showed remarkable pseudoductility and warning signs. The parametric study revealed a critical balance in proportioning the areas of hybrid CFRP to achieve reliable pseudoductility. A maximum of 30% of 400 GPa CFRP is recommended. A higher percentage would lead to a final ultimate load lower than the first failure peak load.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alfano, G., De Cicco, F., and Prota, A. (2012). “Intermediate debonding failure of RC beams retrofitted in flexure with FRP: Experimental results versus prediction of codes of practice.” J. Compos. Constr., 185–195.
American Concrete Institute (ACI). (2008). Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures, Farmington Hills, MI.
Arduini, M., and Nanni, A. (1997). “Behavior of precracked RC beams strengthened with carbon FRP sheets.” J. Compos. Constr., 63–70.
ASTM. (2010). “Standard test methods and definitions for mechanical testing of steel products.” ASTM A370, 1953, West Conshohocken, PA.
ASTM. (2010). “Standard test method for compressive strength of cylindrical concrete specimens.” ASTM C39/C39M, 1921, West Conshohocken, PA.
Bentz, E. C. (2000). “Response 2000.” 〈http://www.ecf.utoronto.ca/~bentz/r2k.htm〉 (Jul. 6, 2011).
Bentz, E. C. (2000). “Response 2000 manual.” 〈http://www.ecf.utoronto.ca/~bentz/manual.shtml〉 (Jul. 6, 2011).
Buyukozturk, O., and Hearing, B. (1998). “Failure behaviour of precracked concrete beams retrofitted with FRP.” J. Compos. Constr., 138–144.
Chajes, M. J., Thomson, T. A., Januszka, T. F., and Fin, W. (1994). “Flexural strengthening of concrete beams using externally bonded composite materials.” Constr. Build. Mater., 8(3), 191–201.
Hollaway, L. C., and Leeming, M. B., eds. (1999). Strengthening of reinforced concrete structures, Woodhead Publishing, Cambridge, U.K., and CRC, Boca Raton, FL.
Hutchinson, A., and Rahimi, H. (1993). “Behaviour of reinforced concrete beams with externally bonded fibre reinforced plastics.” Proc., 5th Int. Conf. on Structural Faults and Repair, Vol. 2, Univ. of Edinburgh, U.K., 221–228.
Hutchinson, A., and Rahimi, H. (1996). “Felxural strengthening of concrete beams with externally bonded FRP reinforcement.” Proc., 2nd Int. Conf. on Advanced Composite Materials in Bridges and Structures, CSCE, Montreal, QC, Canada, 11–14.
Kaiser, H. P. (1989). “Strengthening of reinforced concrete with epoxy-bonded carbon fiber plastics.” Doctoral thesis, ETH Zurich, Zurich, Switzerland.
Ladner, M., Pralong, J., and Weder, C. (1990). “Geklebte Bewehrung: Bemessung und Erfahrung.” EMPA Rep. No. 116/5, EMPA, Dubendorf, CH-8600, Dubendorf, Switzerland (in German).
López-González, J. C., Fernández-Gómez, J., and González-Valle, E. (2012). “Effect of adhesive thickness and concrete strength on FRP-concrete bonds.” J. Compos. Constr., 705–711.
Meier, U. (1987). “Bridge repair with high performance composite materials.” Mater Technik, 15, 125–128.
Saadatrnanesh, H., and Ehsani, M. R. (1991). “RC beams strengthened with GFRP plates. I: Experimental study.” J. Struct. Eng., 3417–3433.
Shi, J., Zhu, H., Wu, Z., Seracino, R., and Wu, G. (2013). “Bond behavior between basalt fiber–reinforced polymer sheet and concrete substrate under the coupled effects of freeze-thaw cycling and sustained load.” J. Compos. Constr., 530–542.
Soudki, K., El-Salakawy, E., and Craig, B. (2007). “Behavior of CFRP strengthened reinforced concrete beams in corrosive environment.” J. Compos. Constr., 291–298.
Triantafillou, T., Deskovic, N., and Deuring, N. (1992). “Strengthening of concrete structures with prestressed fiber reinforced plastic sheets.” ACI Struct. J., 89(3), 235–244.
Vecchio, F. J., and Wong, P. S. (2002a). “VecTor2 and FormWorks.” 〈http://www.civ.utoronto.ca/vector/software.html〉 (Apr. 2, 2013).
Vecchio, F. J., and Wong, P. S. (2002b). “VecTor2 and FormWorks user’s manual.” 〈http://www.civ.utoronto.ca/vector/user_manuals.html〉 (Apr. 2, 2013).
Wu, Z. S., Shao, X. S., Iwashita, K., and Sakamoto, K. (2007). “Strengthening of preloaded RC beams using hybrid carbon sheets.” J. Compos. Constr., 299–307.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jul 29, 2013
Accepted: Oct 29, 2013
Published online: Dec 9, 2013
Discussion open until: May 9, 2014
Published in print: Aug 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.