Punching Shear Resistance of Interior GFRP Reinforced Slab-Column Connections
Publication: Journal of Composites for Construction
Volume 17, Issue 1
Abstract
This paper deals with the punching shear resistance of flat slabs reinforced with glass fiber-reinforced polymer (GFRP) reinforcing bars. A total of six large-scale interior GFRP and steel reinforced slab-column connections with the varying longitudinal tensile reinforcement ratio were tested. A new fracture-mechanics-based empirical formula for estimation of the punching shear resistance of interior GFRP reinforced slab-column connections is also presented in the paper. The formula takes into account effects, span to the effective slab-depth ratio, depth of the compression zone, dowel action, and the size effect on the punching shear resistance of flat slabs reinforced with GFRP bars. The accuracy of the proposed formula was verified against test results obtained by the authors and also by other researchers. In comparison with already known formulas, the proposed formula is in good agreement with the test results and provides predictions of the punching shear resistance with the smallest scatter. A physically reasonable relation between experimental punching resistances and reinforcement ratios of both the GFRP slabs and the steel reinforced concrete (SRC) slabs was obtained when equivalent GFRP reinforcement areas were used for SRC slabs. Predicted punching resistances of SRC slabs, calculated based on the equivalent GFRP reinforcement area, were found to be approximately equal to the resistances of GFRP slabs when the behavior (load-displacement diagram) of SRC slabs resembled the one of GFRP reinforced slabs.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by Vietnamese Foundation for Science & Technology Development (NAFOSTED) under Grant No. 107.04-2012.21.
References
Ahmad, S. H., Zia, P., Yu, T., and Xie, Y. (1993). “Punching shear tests of slabs reinforced with 3-D carbon fiber fabric.” Concr. Int., 16(6), 36–41.
American Concrete Institute (ACI) Committee 318. (2008). Building code requirements for reinforced concrete and commentary, American Concrete Institute, Detroit, MI.
American Concrete Institute (ACI) Committee 440. (2006). Guide for the design and construction of concrete reinforced with FRP bars, Farmington Hills, MI.
Askeland, R. D., and Fulay, P. P. (2005). The science and engineering of materials, 5th Ed., Thomson Learning, Pacific Grove, CA.
Bažant, Z. P., and Cao, Z. (1987). “Size effect in punching shear failure of slabs.” ACI Struct. J., 84(1), 44–53.
Banthia, N., Al-Asaly, M., and Ma, S. (1995). “Behavior of concrete slabs reinforced with fiber-reinforced plastic grid.” J. Mater. Civ. Eng., 7(4), 643–652.
British Standards Institution (BSI). (1997). Structural use of concrete: Code of practice for design and construction, London.
Broomfield, P. J. (2007). Corrosion of steel in concrete: Understanding, investigation and repair, 2nd Ed., Taylor & Francis, London.
CEB-FIP Model Code 1990. (1993). “Design code.” Comité Euro-International du Béton, Redwood Books, London, England.
Chana, P. S. (1986). “Shear failure of reinforced concrete beams.” Ph.D. thesis, Univ. of London, London.
El-Gamal, S., El-Salakawy, E. F., and Benmokrane, B. (2005). “Behavior of concrete bridge deck slabs reinforced with fiber-reinforced polymer bars under concentrated loads.” ACI Struct. J., 102(5), 727–735.
El-Ghandour, A. W., Pilakoutas, K., and Waldron, P. (1999). “New approach for the punching shear capacity prediction of FRP RC flat slabs.” Proc., 4th Int. Symp. on Fibre Reinforced Polymer Reinforcement for Reinforced Concrete Structures (FRPRCS-4), Baltimore, 135–144.
El-Ghandour, A. W., Pilakoutas, K., and Waldron, P. (2003). “Punching shear behavior of fiber reinforced polymers reinforced flat slabs: Experimental study.” J. Compos. Constr., 7(3), 258–265.
European Committee for Standardization (CEN). (2004). “General rules and rules for buildings, part 1.1.”, Brussels.
Florida Dept. of Transportation Highway Administration (FHWA). (2004). “Behavior of fiber-reinforced polymer (FRP) composite piles under vertical loads.” Publication No. FHWA-RD-04-107, FHWA, Washington, DC.
Gastebled, O. J., and May, I. M. (2001). “Fracture Mechanics Model Applied to Shear Failure of Reinforced Concrete Beams without Stirrups.” ACI Struct. J., 98(2), 184–190.
Hognestad, E. (1951). “A study of combined bending and axial load in reinforced concrete members.” Univ. of Illinois, Engineering Experimental Station,.
Hussein, A., et al. (2004). “Two-way concrete slabs reinforced with GFRP bars.” Proc., 4th Int. Conf. on Advanced Composite Materials in Bridges and Structures, Canadian Science Publishing, Ottawa, Canada.
Kinnunen, S., and Nylander, H. (1960). “Punching of concrete slabs without shear reinforcement.” Transactions No. 158, Royal Institute of Technology, Stockholm, Sweden, 112.
Komová, E., et al. (2008). “Stress dependence of the switching field in glass coated microwires.” Acta Phys. Pol. A, 113(1), 135–138.
Lee, J. H., Yang, J. M., and Yoon, Y. S. (2010). “Rational prediction of punching shear strength of slabs reinforced with steel or FRP bars.” Mag. Concr. Res., 62(11), 821–830.
Matthys, S., and Taerwe, L. (2000). “Concrete slabs reinforced with FRP grids. II: Punching resistance.” J. Compos. Constr., 4(3), 154–161.
Menétrey Ph. (2002). “Synthesis of punching failure in reinforced concrete.” Cement Concr. Compos., 24(6), 497–507.
Ospina, C. E., Alexander, S. D. B., and Roger Cheng, J. J. (2003). “Punching of two-way concrete slabs with fiber-reinforced polymer reinforcing bars or grids.” ACI Struct. J., 100(5), 589–598.
Regan, P. E., and Braestrup, M. W. (1985). “Punching shear in reinforced concrete. A state of the art report.”, Comite Euro-International, Lausanne, Switzerland.
Theodorakopoulos, D. D., and Swamy, R. N. (2002). “A design model for punching shear of FRP-reinforced slab-column connections.” Cem. Concr. Compos., 24(6), 509–521.
Theodorakopoulos, D. D., and Swamy, R. N. (2007). “Analytical model to predict punching shear strength of FRP-reinforced concrete flat slabs.” ACI Struct. J., 104(3), 257–266.
Theodorakopoulos, D. D., and Swamy, R. N. (2008). “A design model for punching shear of FRP reinforced slab-column connections.” Cement Concr. Compos., 30(6), 544–555.
Xu, S., and Reinhardt, H. W. (2005). “Shear fracture on the basis of fracture mechanics.” Otto-Graf-J., 16, 21–78.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 18, 2012
Accepted: Aug 9, 2012
Published online: Aug 22, 2012
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.