Reliability Assessment of FRP-Strengthened Concrete Bridge Girders in Shear
Publication: Journal of Composites for Construction
Volume 17, Issue 1
Abstract
This paper presents the results from an investigation into the reliability of reinforced concrete bridge girders strengthened in shear using fiber-reinforced polymers (FRP). Two expressions for the shear design of FRP-strengthened girders were developed as part of a National Cooperative Highway Research Program project. The expressions were developed for two distinct cases, namely, bonded and anchored FRP reinforcement. Uncertainties inherent in the new design models were first assessed using an extensive database of hundreds of experimentally tested specimens. Variabilities in material, fabrication tolerances, dead and live loads, and distribution factors obtained from the literature were then included in a limit state function for the shear strength mode of failure. The reliability of a representative design space comprising 18 bridge girders that cover different span lengths, shear deficiency levels, and girder location (exterior versus interior) was calculated for both bonded and anchored strengthening techniques. The use of approximate expressions for reliability index calculations was deemed unacceptable because of the high scatter in the results. This paper discusses the difference between two reliability methods [Monte Carlo simulations and first-order reliability method (FORM)] that were first used to ensure the validity of FORM in analyzing the developed limit state function. The results showed that the new design expressions result in reliability index values in the range targeted by most design codes (3.00–3.50), albeit lower than the target value used in the calibration of AASHTO load and resistance factor design (LRFD) () in some cases.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based upon work sponsored by the American Association of State Highway and Transportation Officials, in cooperation with the Federal Highway Administration, and was conducted as part of the National Cooperative Highway Research Program Project No. 12–75, administered by the Transportation Research Board of the National Research Council, with Amir Hanna as project manager. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the sponsoring agencies.
References
AASHTO. (1994). LRFD bridge design specifications, American Association of State Highway and Transportation Officials, Washington, DC.
AASHTO. (2004). LRFD bridge design specifications, American Association of State Highway and Transportation Officials, Washington, DC.
American Concrete Institute (ACI). (2002). “Building code requirements for structural concrete.”, ACI, Farmington Hills, MI.
American Concrete Institute (ACI) Committee 440. (1996). “State-of-the-art report on fiber reinforced plastic (FRP) reinforcement for concrete structures.”, ACI, Farmington Hills, MI, 96.
American Concrete Institute (ACI) Committee 440. (2002). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.”, ACI, Farmington Hills, MI, 45.
American Concrete Institute (ACI) Committee 440. (2003). “Guide for the design and construction of concrete reinforced with FRP bars.”, ACI, Farmington Hills, MI, 42.
American Concrete Institute (ACI) Committee 440. (2006). “Guide for the design and construction of structural concrete reinforced with FRP bars.”, ACI, Farmington Hills, MI, 44.
American Concrete Institute (ACI) Committee 440. (2008). “Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures.”, ACI, Farmington Hills, MI, 80.
Bakht, B., et al. (2000). “Canadian bridge design code provisions for fiber-reinforced structures.” J. Compos. Constr., 4(1), 3–15.
Batdorf, S. B., and Ghaffarian, R. (1984). “Size effect and strength variability of unidirectional composites.” Int. J. Fract., 26(2), 113–123.
Belarbi, A., Bae, S.-W., Ayoub, A., Kuchma, D., Mirmiran, A., and Okeil, A. M. (2011). “Design of FRP systems for strengthening concrete girders in shear.”, Transportation Research Board, Washington, DC.
BridgeTech Inc., Tennessee Technological Univ., and Mertz, D. R. (2007). “Simplified live load distribution factor equations.”, Transportation Research Board, Washington, DC, 126.
Bullock, R. E. (1974). “Strength ratios of composite-materials in flexure and in tension.” J. Compos. Mater., 8(2), 200–206.
Canadian Standards Association (CSA). (2002). “Design and construction of building components with fibre-reinforced polymers.”, CSA, Rexdale, ON, Canada.
El-Tawil, S., and Okeil, A. M. (2002). “LRFD flexural provisions for prestressed concrete bridge girders strengthened with carbon fiber-reinforced polymer laminates.” ACI Struct. J., 99(2), 181–190.
Estes, A. C., and Frangopol, D. M. (1998). “RELSYS: A computer program for structural system reliability.” Struct. Eng. Mech., 6(8), 901–919.
Harlow, D. G., and Phoenix, S. L. (1981). “Probability-distributions for the strength of composite-materials. 2. A convergent sequence of tight bounds.” Int. J. Fract., 17(6), 601–630.
Kaminski, B. E. (1973). “Effects of specimen geometry on the strength of composite materials.” Analysis of the test methods for high modulus fibers and composites, ASTM, West Conshohocken, PA, 181–191.
Kulicki, J. M., Wassef, W. G., Kleinhans, D. D., Yoo, C. H., Nowak, A. S., and Grubb, M. (2006). “Development of LRFD specifications for horizontally curved steel girder bridges.”, Transportation Research Board, Washington, DC.
Lima, J. L., and Barros, J. A. (2011). “Reliability analysis of shear strengthening externally bonded FRP models.” Struct. Build., 164(1), 43–56.
Moses, F. (2001). “Calibration of load factors for LRFR bridge evaluation.”, Transportation Research Board, Washington, DC, 56.
Nowak, A. S. (1999). “Calibration of LRFD bridge design code.”, Transportation Research Board, Washington, DC, 37.
Nowak, A. S., and Collins, K. R. (2000). Reliability of structures, McGraw-Hill, New York.
Nowak, A. S., and Szerszen, M. M. (2003). “Calibration of design code for buildings (ACI 318): Part 1. Statistical models for resistance.” ACI Struct. J., 100(3), 377–382.
Okeil, A. M., El-Tawil, S., and Shahawy, M. (2002). “Flexural reliability of RC bridge girders strengthened with CFRP laminates.” J. Bridge Eng., 7(5), 290–299.
Szerszen, M. M., and Nowak, A. S. (2003). “Calibration of design code for buildings (ACI 318): Part 2. Reliability analysis and resistance factors.” ACI Struct. J., 100(3), 383–391.
Taerwe, L., Khalil, H., and Matthys, S. (1997). “Behavior of RC beams strengthened in shear by external CFRP sheets.” Proc., 3rd Int. RILEM Symp. on Non-Metallic (FRP) Reinforcement for Concrete Structures (FRPRCS-3), Japan Concrete Institute, Sapporo, Japan, 483–490.
Zureick, A. H., Bennett, R. M., and Ellingwood, B. R. (2006). “Statistical characterization of fiber-reinforced polymer composite material properties for structural design.” J. Struct. Eng., 132(8), 1320–1327.
Zureick, A. H., Ellingwood, B. R., Nowak, A. S., Mertz, D. R., and Triantafillou, T. C. (2010). “Recommended guide specification for the design of externally bonded FRP systems for repair and strengthening of concrete bridge elements.”, Transportation Research Board, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 30, 2012
Accepted: Jun 5, 2012
Published online: Aug 7, 2012
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.