FRP-Masonry Debonding: Numerical and Experimental Study of the Role of Mortar Joints
Publication: Journal of Composites for Construction
Volume 16, Issue 5
Abstract
Fiber-reinforced polymers (FRP) composites are used as supplementary reinforcement to increase the in-plane shear capacity or to provide out-of-plane load-carrying capability of masonry walls and to modify the collapse mechanism in arches and vaults. In these applications, the efficiency of load transfer is limited by the debonding of FRP from the masonry substrate. In this paper, the debonding mechanism of FRP-masonry is experimentally studied. Experimental procedures and test specimens are designed to investigate the progressive debonding of FRP from brick and mortar substrates and relate it to the response obtained from the FRP-masonry interface. Surface displacements during debonding are obtained using digital image correlation. A one-dimensional numerical model is developed for predicting the fracture behavior along the FRP-masonry interface using the cohesive fracture parameters from the brick and mortar interfaces obtained from the computed strains.
Get full access to this article
View all available purchase options and get full access to this article.
References
Aiello, M. A., and Sciolti, S. M. (2006). “Bond analysis of masonry structures strengthened with CFRP sheets.” Construct. Build. Mater., 20, 90–100.
ASTM C270. (2010). “Standard specification for mortar for unit masonry.” ASTM International, West Conshohocken, PA.
ASTM C39/C39M. (2011). “Standard test method for compressive strength of cylindrical concrete specimens.” ASTM International, West Conshohocken, PA.
Ali-Ahmad, M., Subramaniam, K. V., and Ghosn, M. (2006). “Experimental investigation and fracture analysis of debonding between concrete and FRP.” J. Eng. Mech., 132(9), 914–923.
Ali-Ahmad, M., Subramaniam, K. V., and Ghosn, M. (2007). “Analysis of scaling and instability in FRP-concrete shear debonding for beam-strengthening applications.” J. Eng. Mec., 133(1), 58–67.
Capozucca, R. (2010). “Experimental FRP-SRP–historic masonry delamination.” Comp. Struct., 92, 891–903.
Carloni, C., and Subramaniam, K. V. (2009). “Investigation of the interface fracture during debonding between FRP and masonry.” Adv. Struct. Eng., 12(5), 731–743.
Carloni, C., and Subramaniam, K. V. (2010). “Direct determination of cohesive stress transfer during debonding of FRP from concrete.” Comp. Struct., 93, 184–192.
Casareto, M., Olivieri, A., Romelli, A., and Lagomarsino, S. (2003). “Bond behavior of FRP laminates adhered to masonry.” Proc. International Conf. Advancing with Composites, Plast 2003, Crivelli-Visconti, I., ed., Milan, Italy.
Fedele, R., and Milani, G. (2010). “A numerical insight into the response of masonry reinforced by FRP strips. The case of perfect adhesion.” Comp. Struct., 92, 2345–2357.
Garbin, E., Panizza, M., and Valluzzi, M. (2010). “Experimental assessment of bond behaviour of fibre-reinforced polymers on brick masonry.” Struct. Eng. Int., 20(4), 392–399.
Grande, E., Imbimbo, M., and Sacco, E. (2011). “Simple model for bond behavior of masonry elements strengthened with FRP.” J. Compos. Constr., 15(3), 354–363.
Lu, X. Z., Teng, J. G., Ye, L. P., and Jiang, J. J. (2005). “Bond-slip models for FRP sheets/plates bonded to concrete.” Eng. Struct., 27, 920–937.
Mosallam, A. S. (2007). “Out-of-plane flexural behaviour of unreinforced red brick walls strengthened with FRP composites.” Compos.: Part B, 38, 559–574.
Prota, A., Manfredi, G., and Nardone, F. (2008). “Assessment of design formulas for in-plane FRP strengthening of masonry walls.” J. Compos. Constr., 12(6), 643–649.
Seim, W., and Pfeiffer, U. (2011). “Local poststrengthening of masonry structures with fiber-reinforced polymers (FRPs).” Constr. Build. Mater., 25, 3393–3403.
Stratford, T., Pascale, G., Manfroni, O., and Bonfiglioli, B. (2004). “Shear strengthening masonry panels with sheet glass-fiber reinforced polymer.” J. Compos. Constr., 8(5), 434–443.
Subramaniam, K. V., Carloni, C., and Nobile, L. (2007). “Width effect in the interface fracture during debonding of FRP from concrete.” Eng Fract. Mech., 74(4), 578–594.
Subramaniam, K. V., Carloni, C., and Nobile, L. (2011). “An understanding of the width effect in FRP–Concrete debonding.” Strain, 47, 127–137.
Subramaniam, V. K., Popovics, J. S., and Shah, S. P. (2000). “Determining elastic properties of concrete using vibrational resonance frequencies of standard test cylinders.” Cem. Concr. Aggregates, 22(2), 81–89.
Sutton, M. A., Wolters, W. J., Peters, W. H., Ranson, W. F., and McNeill, S. R. (1983). “Determination of displacements using an improved digital correlation method.” Image Vis. Comput., 1(3), 133–139.
Taljsten, B. (1997). “Defining anchor lengths of steel and CFRP plates bonded to concrete.” Int. J. Adhes. Adhes., 17(4), 319–327.
Tan, K. H., and Patoary, M. K. H. (2004). “Strengthening of masonry walls against out-of-plane loads using fiber-reinforced polymer reinforcement.” J. Compos. Constr., Jan–Feb 2004, 8(1), 79–87.
Willis, C. R., Yang, Q., Seracino, R., and Griffith, M. C. (2009). “Damaged masonry walls in two-way bending retrofitted with vertical FRP strips.” Constr. Build. Mater., 23(4), 1591–1604.
Xia, S., and Oehlers, D. (2006). “Debonding mechanisms in FRP plated unreinforced masonry under out-of-plane loading.” Adv. Struct. Eng., 9(5), 619–637.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Jun 15, 2011
Accepted: Jan 31, 2012
Published online: Feb 3, 2012
Published in print: Oct 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.