Experimental Study on the Fatigue Behavior of Steel Beams Strengthened with Different Fiber-Reinforced Composite Plates
Publication: Journal of Composites for Construction
Volume 16, Issue 2
Abstract
An experimental study was conducted to investigate the fatigue behavior of artificially notched steel beams strengthened with four different types of materials tested under equivalent tensile stiffness. These materials include high-modulus carbon-fiber-reinforced polymer (HM-CFRP) plate, high-strength CFRP (HS-CFRP) plate, steel-wire basalt-fiber-reinforced polymer (SW-BFRP) plate, and welded steel plate. Some key parameters, such as material type, the number of HS-CFRP layers, the configuration of HS-CFRP, and the interface treatment of SW-BFRP, are discussed. Compared to the traditional welded steel-plate method, the test results show that the application of a fiber-reinforced composite plate can not only delay crack initiation, decrease the crack growth rate, and prolong the fatigue life, but also reduce the stiffness decay and residual deflection. HM-CFRP exhibited the best strengthening performance; however, SW-BFRP is the optimal strengthening material on the basis of the cost–performance ratio. The fatigue behavior of steel beams can be improved significantly by increasing the layers of strengthening material. SW-BFRP with a rough surface can prolong the fatigue life of steel beams more effectively than SW-BFRP with a smooth surface. The plate configuration has certain effects on the fatigue life.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge financial support from the National Science Foundation of China (No. 51078077, 51178099), the National Basic Research Program of China (973 Program) (No. 2012CB026200), and the National Key Technology R&D Program of China in the 12th Five-Year Plan (No. 2011BAB03B09). Supplementary support was provided by the Fok Ying-Tong Education Foundation of China (No. 122011) to Gang Wu.
References
Al-Saidy, A. H., Klaiber, F. W., and Wipf, T. J. (2004). “Repair of steel composite beams with carbon fiber reinforced polymer plates.” J. Compos. Constr., 8(2), 163–172.JCCOF2
Bocciarelli, M., Colombi, P., Fava, G., and Poggi, C. (2009). “Fatigue performance of tensile steel members strengthened with CFRP plates.” Compos. Struct., 87(4), 334–343.COMSE2
Dawood, M., Rizkalla, S., and Sumner, E. (2007). “Fatigue and overloading behavior of steel-concrete composite flexural members strengthened with high modulus CFRP materials.” J. Compos. Constr., 11(6), 659–669.JCCOF2
Fam, A., MacDougall, C., and Shaat, A. (2009). “Upgrading steel-concrete composite girders and repair of damaged steel beams using bonded CFRP laminates.” Thin Wall Struct., 47(10), 1122–1135.
Jones, S. C., and Civjan, S. A. (2003). “Application of fiber reinforced polymer overlays to extend steel fatigue life.” J. Compos. Constr., 7(4), 331–338.JCCOF2
Kim, S. J., Smith, S. T., and Young, B. (2010). “Effect of surface preparation on the strength of FRP-to-mild steel and FRP-to-stainless steel joints.” Proc., 5th Int. Conf. on FRP Composites in Civil Engineering (CICE2010), Tsinghua University Press, Beijing, 869–872.
Liu, H. B., Al-Mahaidi, R., and Zhao, X. L. (2009). “Experimental study of fatigue crack growth behavior in adhesively reinforced steel structures.” Compos. Struct., 90(1), 12–20.COMSE2
Moy, S. S. J. (2002). “Early age curing under cyclic loading—An investigation into stiffness development in carbon fibre reinforced steel beams.” Advanced Polymer Composites for Structural Applications in Construction: Proc., 1st Int. Conf., Southampton Univ., UK, 188–194.
Moy, S. S. J., and Nikoukar, F. (2002). “Flexural behaviour of steel beams reinforced with carbon fibre polymer composite.” Advanced Polymer Composites for Structural Applications in Construction: Proc., 1st Int. Conf., Southampton Univ., UK, 195–202.
Sallam, H. E. M., Badawy, A. A. M., Saba, A. M., and Mikhail, F. A. (2010). “Flexural behavior of strengthened steel-concrete composite beams by various plating methods.” J. Constr. Steel. Res., 66(8–9), 1081–1087.
Sen, R., Liby, L., and Mullins, G. (2001). “Strengthening steel bridge sections using CFRP laminates.” Compos.: Part B, 32(4), 309–322.CPBEFF
Shaat, A., and Fam, A. (2008). “Repair of cracked steel girders connected to concrete slabs using carbon-fiber-reinforced polymer sheets.” J. Compos. Constr., 12(6), 650–659.JCCOF2
TavakkolizadehM., and Saadatmanesh, H. (2003a). “Fatigue strength of steel girders strengthened with carbon fiber reinforced polymer patch.” J. Struct. Eng., 129(2), 186–196.
Tavakkolizadeh, M., and Saadatmanesh, H. (2003b). “Repair of damaged steel-concrete composite girders using carbon fiber-reinforced polymer sheets.” J. Compos. Constr., 7(4), 311–322.JCCOF2
Tavakkolizadeh, M., and Saadatmanesh, H. (2003c). “Strengthening of steel-concrete composite girders using carbon fiber reinforced polymers sheets.” J. Struct. Eng., 129(1), 30–40.
Teng, J. G., Fernando, D., Yu, T, and Zhao, X. L. (2010). “Treatment of steel surfaces for effective adhesive bonding.” Proc., 5th Int. Conf. on FRP Composites in Civil Engineering (CICE2010), Tsinghua University Press, Beijing, 865–868.
Tsouvalis, N. G., Mirisiotis, L. S., and Dimou, D. N. (2009). “Experimental and numerical study of the fatigue behavior of composite patch reinforced cracked steel plates.” Int. J. Fatigue, 31(10), 1613–1627.IJFADB
Wu, G., Wu, Z. S., Luo, Y. B., Sun, Z. Y., and Hu, X. Q. (2010a). “Mechanical properties of steel-FRP composite bar under uniaxial and cyclic tensile loads.” J. Mater. Civ. Eng., 22(10), 1056–1066.JMCEE7
Wu, Z. S., Ou, J. P., Wu, G., Wang, Y. L., and Feng, W. Q. (2009). “A type of continuous Fiber-Steel wires composite plate.” China National Invention Patent, Publication No: CN101581133A (in Chinese).
Wu, Z. S., Wang, X., Iwashita, K., Sasaki, T., and Hamaguchi, Y. (2010b). “Tensile fatigue behaviour of FRP and hybrid FRP sheets.” Compos.: Part B, 41(5), 396–402.CPBEFF
Wu, Z. S., Wang, X., Wu, G. (2011). “Advancement of basalt fiber composites towards infrastructural applications.” Proc., Int. Symp. on Innovation and Sustainability of Structures in Civil Engineering (ISISS2011), Southeast University Press, Nanjing, China, 195–213.
Zhao, X. L., and Zhang, L. (2007). “State-of-the-art review on FRP strengthened steel structures.” Eng. Struct., 29(8), 1808–1823.ENSTDF
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Jan 31, 2011
Accepted: Aug 1, 2011
Published online: Aug 3, 2011
Published in print: Apr 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.