Caisson-Bored Pile Composite Anchorage Foundation for Long-Span Suspension Bridge: Feasibility Study and Parametric Analysis
Publication: Journal of Bridge Engineering
Volume 27, Issue 12
Abstract
This paper proposes a novel form of gravity foundation for long-span suspension bridges. The foundation combines a caisson with bored piles and thereafter is termed a caisson-bored pile composite anchorage (CBPCA) foundation. Based on a typical suspension bridge case study with traditional caisson foundation, the feasibility of the proposed foundation was evaluated. To further capture the performance of the CBPCA foundation, three-dimensional (3D) finite-element analyses were performed. The 3D finite-element method (FEM) was validated by comparing the simulated horizontal displacements of a nine-pile group with the reported field monitoring data. Parametric studies were also conducted to investigate the effects of various parameters associated with bored piles on the CBPCA foundation performance. The numerical analysis results indicate that increasing the pile diameter can significantly reduce the horizontal displacements of the theoretical joint point (TJP) and the structural forces of bored piles. In addition, the effect of the pile arrangement was also studied. The feasibility of reducing construction time and costs by adjusting the length of some bored piles was also discussed. Moreover, the soil strength has a great influence on the stability of the CBPCA foundation, implying that it may be not suitable for soft soil conditions, namely, a soil strength ratio smaller than 0.4 in this study.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Natural Science Foundation of China [Grant Numbers 51778575, 52078457]; and the Science and Technology Plan Project of Department of Transportation of Zhejiang Province [Grant Number 2020050].
Notation
The following symbols are used in this paper:
- c′
- effective cohesion;
- cu
- undrained shear strength;
- D
- bored Pile diameter;
- E
- modulus of elasticity of bored pile;
- E′
- effective Young’s modulus of medium-weathered sandstone;
- tangent stiffness from primary oedometer loading;
- secant stiffness in standard drained triaxial test;
- unloading/reloading stiffness;
- E50
- secant stiffness;
- e
- void ratio;
- Fa
- applied load on the main cables;
- Fd
- designed load on the main cables;
- L
- bored pile length;
- m
- power of stress-level dependency of stiffness;
- NSPT
- value of standard penetration test;
- pref
- reference pressure;
- Rs
- soil strength ratio;
- R
- ratio of the applied load on the main cables to the designed load on the main cables;
- Rinter
- interface reduction factor;
- Rm
- maximum R-value;
- Z
- depth of bored Pile blow caisson bottom;
- γ
- unit weight;
- effective confining stress;
- υ′
- effective Poisson’s ratio of medium-weathered sandstone;
- φ′
- effective angle of internal friction; and
- ψ
- dilatancy angle.
References
Aladejare, A. E., and Y. Wang. 2018. “Influence of rock property correlation on reliability analysis of rock slope stability: From property characterization to reliability analysis.” Geosci. Front. 9 (6): 1639–1648. https://doi.org/10.1016/j.gsf.2017.10.003.
Baandrup, M., P. N. Poulsen, J. F. Olesen, and H. Polk. 2019. “Parametric optimization of orthotropic girders in a cable-supported bridge.” J. Bridge Eng. 24 (12): 04019118. https://doi.org/10.1061/(asce)be.1943-5592.0001499.
Brinkgreve, R. B. J., S. Kumarswamy, and W. M. Swolfs. 2017. Plaxis 3D 2017 user’s manual. Delft, Netherlands: Plaxis bv.
Bryson, L. S., and D. G. Zapata-Medina. 2012. “Method for estimating system stiffness for excavation support walls.” J. Geotech. Geoenviron. Eng. 138 (9): 1104–1115. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000683.
Cao, H. Y., Y. P. Chen, J. Li, and S. Liu. 2021. “Static characteristics analysis of three-tower suspension bridges with central buckle using a simplified model.” Eng. Struct. 245: 112916. https://doi.org/10.1016/j.engstruct.2021.112916.
Cao, H. Y., X. D. Qian, Z. J. Chen, and H. P. Zhu. 2017. “Layout and size optimization of suspension bridges based on coupled modelling approach and enhanced particle swarm optimization.” Eng. Struct. 146: 170–183. https://doi.org/10.1016/j.engstruct.2017.05.048.
Cao, H. Y., X. D. Qian, Y. L. Zhou, Z. J. Chen, and H. P. Zhu. 2018. “Feasible range for midtower lateral stiffness in three-tower suspension bridges.” J. Bridge Eng. 23 (3): 06017009. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001196.
Comanducci, G., F. Ubertini, and A. L. Materazzi. 2015. “Structural health monitoring of suspension bridges with features affected by changing wind speed.” J. Wind Eng. Ind. Aerodyn. 141: 12–26. https://doi.org/10.1016/j.jweia.2015.02.007.
Conte, J. P., X. F. He, B. Moaveni, S. F. Masri, J. P. Caffrey, M. Wahbeh, F. Tasbihgoo, D. H. Whang, and A. Elgamal. 2008. “Dynamic testing of Alfred Zampa memorial bridge.” J. Struct. Eng. 134 (6): 1006–1015. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:6(1006).
Cross, E. J., K. Y. Koo, J. M. W. Brownjohn, and K. Worden. 2013. “Long-term monitoring and data analysis of the Tamar Bridge.” Mech. Syst. Sig. Process. 35 (1–2): 16–34. https://doi.org/10.1016/j.ymssp.2012.08.026.
Cui, M. Z., W. X. Ren, and Y. G. Yin. 2021. “Numerical analysis and field load testing of a suspension bridge with a root Pile anchorage.” Structures 34: 1373–1382. https://doi.org/10.1016/j.istruc.2021.08.086.
Deb, P., and S. K. Pal. 2019. “Numerical analysis of Piled raft foundation under combined vertical and lateral loading.” Ocean Eng. 190: 106431. https://doi.org/10.1016/j.oceaneng.2019.106431.
Di, Q. H., Y. H. Li, Y. C. Xing, and X. Hu. 2017. “Modal analysis of the Saint-Bachi suspension aqueduct bridge considering fluid–structure interaction.” J. Bridge Eng. 22 (11): 05017010. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001126.
Finno, R. J., and M. Calvello. 2005. “Supported excavations: Observational method and inverse modeling.” J. Geotech. Geoenviron. Eng. 131 (7): 826–836. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:7(826).
Furuya, N., R. Yamaoka, and B. C. Paulson. 1994. “Construction of Akashi-Kaikyo bridge west anchorage.” J. Constr. Eng. Manage. 120 (2): 337–356. https://doi.org/10.1061/(ASCE)0733-9364(1994)120:2(337).
Gou, H. Y., C. Liu, Y. Bao, B. Han, and Q. H. Pu. 2021. “Construction monitoring of self-anchored suspension bridge with inclined tower.” J. Bridge Eng. 26 (10): 05021011. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001777.
Guo, P. P., X. N. Gong, and Y. X. Wang. 2019. “Displacement and force analyses of braced structure of deep excavation considering unsymmetrical surcharge effect.” Comput. Geotech. 113: 103102. https://doi.org/10.1016/j.compgeo.2019.103102.
Han, Y. F., X. R. Liu, D. L. Li, Y. L. Tu, Z. Y. Deng, D. S. Liu, and X. C. Wu. 2020. “Model test on the bearing behaviors of the tunnel-type anchorage in soft rock with underlying weak interlayers.” Bull. Eng. Geol. Environ. 79 (2): 1023–1040. https://doi.org/10.1007/s10064-019-01564-5.
Hazzar, L., M. N. Hussien, and M. Karray. 2017. “On the behaviour of Pile groups under combined lateral and vertical loading.” Ocean Eng. 131: 174–185. https://doi.org/10.1016/j.oceaneng.2017.01.006.
Huang, D. Z., and W. Z. Chen. 2019. “Cable structures in bridge engineering.” J. Bridge Eng. 24 (8): 02019001. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001418.
Ingham, T. J., S. Rodriguez, and M. Nader. 1997. “Nonlinear analysis of the Vincent Thomas Bridge for seismic retrofit.” Comput. Struct. 64 (5-6): 1221–1238. https://doi.org/10.1016/S0045-7949(97)00031-X.
Kawaguchi, K., and F. Tatsuoka. 2010. “Several geotechnical design and construction issues with Akashi strait bridge.” Soils Found. 50 (6): 829–845. https://doi.org/10.3208/sandf.50.829.
Kitagawa, M. 2004. “Technology of the Akashi Kaikyo bridge.” Struct. Control Health Monit. 11 (2): 75–90. https://doi.org/10.1002/stc.31.
Kusano, I., M. C. Montoya, A. Baldomir, F. Nieto, J. A. Jurado, and S. Hernandez. 2020. “Reliability based design optimization for bridge girder shape and plate thicknesses of long-span suspension bridges considering aeroelastic constraint.” J. Wind Eng. Ind. Aerodyn. 202: 104176. https://doi.org/10.1016/j.jweia.2020.104176.
Kwon, G., M. D. Engelhardt, and R. E. Klingner. 2012. “Parametric studies and preliminary design recommendations on the use of postinstalled shear connectors for strengthening noncomposite steel bridges.” J. Bridge Eng. 17 (2): 310–317. https://doi.org/10.1061/(asce)be.1943-5592.0000261.
Kwon, S. D., H. K. Lee, S. H. Lee, and J. H. Kim. 2013. “Mitigating the effects of wind on suspension bridge catwalks.” J. Bridge Eng. 18 (7): 624–632. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000410.
Lemnitzer, A., P. Khalili-Tehrani, E. R. Ahlberg, C. Rha, E. Taciroglu, J. W. Wallace, and J. P. Stewart. 2010. “Nonlinear efficiency of bored Pile group under lateral loading.” J. Geotech. Geoenviron. Eng. 136 (12): 1673–1685. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000383.
Li, J. P., Y. S. Li, and R. L. Wang. 2004. “Research on displacement of anchorage of suspension bridge.” Chin. Rock Soil Mech. 28 (1): 145–150.
Li, Y. J., R. Luo, Q. H. Zhang, G. Q. Xiao, L. M. Zhou, and Y. T. Zhang. 2017. “Model test and numerical simulation on the bearing mechanism of tunnel-type anchorage.” Geomech. Eng. 12 (1): 139–160. https://doi.org/10.12989/gae.2017.12.1.139.
Liu, H. X., and B. K. Low. 2018. “Reliability-based design of tunnelling problems and insights for Eurocode 7.” Comput. Geotech. 97: 42–51. https://doi.org/10.1016/j.compgeo.2017.12.005.
Liu, X., G. J. Shao, J. S. Huang, J. B. Su, and H. Z. Xu. 2021. “Stability analysis of gravity anchorage: A case study of Taizhou Yangtze River Bridge.” Eur. J. Environ. Civ. Eng. 25 (6): 1002–1024. https://doi.org/10.1080/19648189.2018.1562997.
Liu, X. R., Y. F. Han, D. L. Li, Y. L. Tu, Z. Y. Deng, C. T. Yu, and X. C. Wu. 2019. “Anti-pull mechanisms and weak interlayer parameter sensitivity analysis of tunnel-type anchorages in soft rock with underlying weak interlayers.” Eng. Geol. 253: 123–136. https://doi.org/0.1016/j.enggeo.2019.03.012.
Lonetti, P., and A. Pascuzzo. 2014. “Optimum design analysis of hybrid cable-stayed suspension bridges.” Adv. Eng. Software 73: 53–66. https://doi.org/10.1016/j.advengsoft.2014.03.004.
Luo, L. G., L. C. Cui, H. Y. Shi, C. Guo, and S. P. Yi. 2019. “Experimental study of bearing capacity of underground diaphragm wall-gravity anchorage composite foundation.” Chin. Rock Soil Mech. 40 (3): 1049–1058. https://doi.org/10.16285/j.rsm.2017.1978.
Matarazzo, T. J., P. Santi, S. N. Pakzad, K. Carter, C. Ratti, B. Moaveni, C. Osgood, and N. Jacob. 2018. “Crowdsensing framework for monitoring bridge vibrations using moving smartphones.” Proc. IEEE 106 (4): 577–593. https://doi.org/10.1109/JPROC.2018.2808759.
Matsumoto, K., C. A. L. Panting, N. Kitratporn, W. Takeuchi, K. Nagai, and E. Iwasaki. 2018. “Performance assessment using structural analysis and spatial measurement of a damaged suspension bridge: Case study of Twantay Bridge, Myanmar.” J. Bridge Eng. 23 (10): 05018008. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001293.
McVay, M., R. Casper, and T. I. Shang. 1995. “Lateral response of three-row groups in loose to dense sands at 3D and 5D Pile spacing.” J. Geotech. Eng. 121 (5): 436–441. https://doi.org/10.1061/(ASCE)0733-9410(1995)121:5(436).
MoT (Ministry of Transport). 2015. Specifications for design of highway suspension bridge. JTGT/D 65-05-2015. Beijing: China Communications Press.
Nguyen, D. D. C., D. S. Kim, and S. B. Jo. 2013. “Settlement of Piled rafts with different Pile arrangement schemes via centrifuge tests.” J. Geotech. Geoenviron. Eng. 139 (10): 1690–1698. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000908.
Ruesta, P. F., and F. C. Townsend. 1997. “Evaluation of laterally loaded pile group at Roosevelt bridge.” J. Geotech. Geoenviron. Eng. 123 (12): 1153–1161. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:12(1153).
Schanz, T., P. A. Vermeer, and P. Bonnier. 1999. The hardening soil model: Formulation and verification. In Beyond 2000 in computational geotechnics-10 years of PLAXIS, edited by R. B. J. Brinkgreve. Amsterdam, Netherlands: Routledge.
Shin, M., and B. Andrawes. 2014. “Parametric study of RC bridge columns actively confined with shape memory alloy spirals under lateral cyclic loading.” J. Bridge Eng. 19 (10): 04014040. https://doi.org/10.1061/(asce)be.1943-5592.0000609.
Stewart, J. P., E. Taciroglu, J. W. Wallace, E. R. Ahlberg, A. Lemnitzer, C. Rha, P. Tehrani, S. Keowen, R. L. Nigbor, and A. Salamanca. 2007. Full scale cyclic large deflection testing of foundation support systems for highway bridges. I: Drilled shaft foundations. Rep. No. UCLA SGEL-01. Los Angeles: Univ. of California.
Wang, W. D., H. R. Wang, and Z. H. Xu. 2012. “Experimental study of parameters of hardening soil model for numerical analysis of excavations of foundation pits.” Chin. Rock Soil Mech. 33 (8): 2283–2290.
Wang, X., W. Yang, X. Zhang, and P. Zhu. 2020. “Experimental and numerical study on a novel cable anchorage system to improve the maintainability of suspension bridges.” Structures 27: 2126–2136. https://doi.org/10.1016/j.istruc.2020.08.031.
Wang, X. L., S. B. Chai, and Y. Xu. 2016. “Deformation characteristics of double-cable multispan suspension bridges.” J. Bridge Eng. 21 (4): 06015007. https://doi.org/10.1061/(asce)be.1943-5592.0000858.
Xu, Y. L., X. H. Zhang, S. Zhan, X. J. Hong, L. D. Zhu, Y. Xia, and S. Zhu. 2012. “Testbed for structural health monitoring of long-span suspension bridges.” J. Bridge Eng. 17 (6): 896–906. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000349.
Xu, Y. L., X. H. Zhang, S. Y. Zhu, and S. Zhan. 2016. “Multi-type sensor placement and response reconstruction for structural health monitoring of long-span suspension bridges.” Sci. Bull. 61 (4): 313–329. https://doi.org/10.1007/s11434-016-1000-7.
Yang, S. K., X. H. Ren, and J. X. Zhang. 2011. “Study on embedded length of Piles for slope reinforced with one row of Piles.” J. Rock Mech. Geotech. Eng. 3 (2): 167–178. https://doi.org/10.3724/SP.J.1235.2011.00167.
Yang, Y. Q., X. Wang, and Z. S. Wu. 2016. “Evaluation of the static and dynamic behaviors of long-span suspension bridges with FRP cables.” J. Bridge Eng. 21 (12): 06016008. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000972.
Yu, H. Y., F. Y. Xu, C. M. Ma, A. Q. Zhou, and M. J. Zhang. 2021. “Experimental research on the aerodynamic responses of a long-span pipeline suspension bridge.” Eng. Struct. 245: 112856. https://doi.org/10.1016/j.engstruct.2021.112856.
Zhang, Q. H., Z. Y. Cheng, C. Cui, Y. Bao, J. He, and Q. Li. 2017. “Analytical model for frictional resistance between cable and saddle of suspension bridges equipped with vertical friction plates.” J. Bridge Eng. 22 (1): 04016103. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000986.
Zhang, Q. H., H. L. Guo, Y. Bao, Z. Y. Cheng, and D. L. Jia. 2020a. “Antislip safety of double-cable multispan suspension bridges with innovative saddles.” J. Bridge Eng. 25 (5): 04020021. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001544.
Zhang, Q. H., Y. J. Li, M. W. Yu, H. H. Hu, and J. H. Hu. 2015a. “Study of the rock foundation stability of the Aizhai suspension bridge over a deep canyon area in China.” Eng. Geol. 198: 65–77. https://doi.org/10.1016/j.enggeo.2015.09.012.
Zhang, W., H. Li, Y. Q. Li, R. H. Zhang, A. T. C. Goh, and H. L. Liu. 2021a. “Effects of jet grouting slabs on responses for deep braced excavations.” Underground Space 6 (2): 185–194. https://doi.org/10.1016/j.undsp.2020.02.002.
Zhang, W. G., and A. T. C. Goh. 2018. “Reliability analysis of geotechnical infrastructures: Introduction.” Geosci. Front. 9 (6): 1595–1596. https://doi.org/10.1016/j.gsf.2018.01.001.
Zhang, W. G., A. T. C. Goh, and F. Xuan. 2015b. “A simple prediction model for wall deflection caused by braced excavation in clays.” Comput. Geotech. 63: 67–72. https://doi.org/10.1016/j.compgeo.2014.09.001.
Zhang, W. G., Z. J. Hou, A. T. C. Goh, and R. H. Zhang. 2019a. “Estimation of strut forces for braced excavation in granular soils from numerical analysis and case histories.” Comput. Geotech. 106: 286–295. https://doi.org/10.1016/j.compgeo.2018.11.006.
Zhang, W. G., Y. Q. Li, A. T. C. Goh, and R. H. Zhang. 2020b. “Numerical study of the performance of jet grout Piles for braced excavations in soft clay.” Comput. Geotech. 124: 103631. https://doi.org/10.1016/j.compgeo.2020.103631.
Zhang, W. G., R. H. Zhang, W. Wang, F. Zhang, and A. T. C. Goh. 2019b. “A multivariate adaptive regression splines model for determining horizontal wall deflection envelope for braced excavations in clays.” Tunnelling Underground Space Technol. 84: 461–471. https://doi.org/10.1016/j.tust.2018.11.046.
Zhang, W. M., J. Q. Chang, X. F. Lu, G. M. Tian, and J. G. Li. 2021b. “Suspension bridge deformation and internal forces under the concentrated live load: Analytical algorithm.” Eng. Struct. 248: 113271. https://doi.org/10.1016/j.engstruct.2021.113271.
Zheng, W. Z., H. Wang, J. Li, and H. J. Shen. 2020. “Parametric study of superelastic-sliding LRB system for seismic response control of continuous bridges.” J. Bridge Eng. 25 (9): 04020062. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001596.
Zhou, T. M., S. S. Roy, J. J. Wang, X. Nie, H. B. Chen, and Y. L. Mo. 2020. “Parametric study on the structural behavior and failure mechanism of skewed inverted-T bent caps.” J. Bridge Eng. 25 (11): 04020092. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001629.
Zhou, Z. J., C. R. Chen, L. F. Wang, Y. Q. Tian, H. M. Feng, and K. C. Wang. 2021. “Stability analysis of the gravity anchorage of a suspension bridge based on large-scale field tests.” Civ. Eng. J.-Staveb. Obz. 30 (1): 282–297. https://doi.org/10.14311/CEJ.2021.01.0021.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Feb 10, 2022
Accepted: Aug 7, 2022
Published online: Oct 10, 2022
Published in print: Dec 1, 2022
Discussion open until: Mar 10, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Xiaoqing Zhao, Xiaonan Gong, Yongle Duan, Panpan Guo, Load-bearing performance of caisson-bored pile composite anchorage foundation for long-span suspension bridge: 1-g model tests, Acta Geotechnica, 10.1007/s11440-023-01808-5, (2023).