Girder–Deck Interface: Partial Debonding, Deck Replacement, and Composite Action
Publication: Journal of Bridge Engineering
Volume 24, Issue 1
Abstract
Results are reported from tests of three precast, prestressed concrete girders under fatigue-type cyclic and monotonic loading conducted after deck removal and replacement. Although deck demolition altered the top surface of the girders, the girder–deck interfaces exhibited shear strengths greater than their nominal strength (based on the 2012 AASHTO LRFD Specification) after 2 × 106 cycles of loading to 45 and 30% of their nominal strength for troweled and roughened interfaces, respectively. A partially debonded detail was used for two of the girders to protect the girder top flange, which was wide and thin, during deck demolition. The roofing felt used to debond the girder–deck interface over the flanges reduced the effort required for deck removal by 65%, compared with the typical detail, eliminated chipping hammer–induced damage to the girder flanges, and still resulted in sustained composite action under 2 × 106 cycles of loading. The width of the bonded interface had little effect on girder stiffness and no observed effect on the width of deck effective in bending.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support was provided by the Kansas DOT (Grant C2036). Coreslab Structures donated the precast concrete girders. Input from Shawn Schwensen and Colby Farlow of the Kansas DOT is gratefully acknowledged. The conclusions are those of the authors and do not necessarily represent the views of the sponsors.
References
AASHTO. 2012a. AASHTO LRFD bridge design specifications. 6th ed. Washington, DC: AASHTO.
AASHTO. 2012b. Standard specification for air-entraining admixtures for concrete. M154MM154-12-UL. Washington, DC: AASHTO.
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete and commentary. ACI 318-14. Farmington Hills, MI: ACI.
Assad, S. A., and G. Morcous. 2016. “Evaluating the impact of bridge-deck removal on the performance of precast/prestressed concrete I-girders.” J. Perform. Constr. Facil. 30 (3): 04015032. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000769.
ASTM. 2015. Standard specification for chemical admixtures for concrete. C494/C494M-15. West Conshohocken, PA: ASTM.
ASTM. 2016a. Standard specification for air-entraining admixtures for concrete. C260/C260M-10a. West Conshohocken, PA: ASTM.
ASTM. 2016b. Standard specification for asphalt-saturated organic felt underlayment used in steep slope roofing. D4869/D4869M-16a. West Conshohocken, PA: ASTM.
ASTM. 2016c. Standard specification for deformed and plain carbon-steel bars for concrete reinforcement. A615/A615M-16. West Conshohocken, PA: ASTM.
ASTM. 2017a. Standard specification for low-relaxation, seven-wire steel strand for prestressed concrete. A416/A416M-17a. West Conshohocken, PA: ASTM.
ASTM. 2017b. Standard test method for compressive strength of cylindrical concrete specimens. C39/C39M-17b. West Conshohocken, PA: ASTM.
Badoux, J. C., and C. L. Hulsbos. 1967. “Horizontal shear connection in composite concrete beams under repeated loads.” ACI J. Proc. 64 (12): 811–819. https://doi.org/10.14359/7609.
Beacham, M., and D. Derrick. 1999. “Longer bridge spans with Nebraska’s NU I-girders.” TR News 203: 42–43.
Chung, H. W., and T. Y. Chung. 1976. “Prestressed concrete composite beams under repeated loading.” ACI J. Proc. 73 (5): 291–295. https://doi.org/10.14359/11074.
Hanson, N. W. 1960. “Precast-prestressed concrete bridges 2. Horizontal shear connections.” J. PCA Res. Dev. Lab. 2 (2): 38–58.
Iyer, H. 2005. “The effects of shear deformation in rectangular and wide flange sections.” Master’s thesis, Virginia Polytechnic Institute and State Univ.
Kahn, L. F., and A. Slapkus. 2004. “Interface shear in high strength composite T-beams.” PCI J. 49 (4): 102–110.
Kamel, M. R. 1996. “Innovative precast concrete composite bridge systems.” Ph.D. dissertation, Univ. of Nebraska–Lincoln.
KDOT (Kansas Dept. of Transportation). 2015. Standard specifications for state road & bridge construction. Topeka, KS: KDOT.
Li, C. 2017. “Composite action in prestressed NU I-girder bridge deck systems constructed with bond breakers to facilitate deck removal.” Ph.D. dissertation, Univ. of Kansas.
Loov, R. E., and A. K. Patnaik. 1994. “Horizontal shear strength of composite concrete beams with a rough interface.” PCI J. 39 (1): 48–69.
Saemann, J. C., and G. W. Washa. 1964. “Horizontal shear connections between precast beams and cast-in-place slabs.” ACI J. Proc. 61 (11): 1383–1410. https://doi.org/10.14359/7832.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Feb 19, 2018
Accepted: May 31, 2018
Published online: Oct 17, 2018
Published in print: Jan 1, 2019
Discussion open until: Mar 17, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.