Effects of Geometric Imperfections on the Bracing Performance of Cross Beams during Construction of Composite Bridges
Publication: Journal of Bridge Engineering
Volume 22, Issue 1
Abstract
Steel girders require stability controls for different construction stages before the lateral-torsional support from the concrete deck occurs. The load-carrying capacity of bridge girders and bracing forces generated in their bracings are very sensitive to the girders’ initial imperfections in terms of both the magnitude and distribution along the span. Relatively little knowledge is available in this matter; however, decisions on the “worst” shape of imperfections that gives a conservative resistance and/or maximizes the bracings forces is often not an easy task in practice. The present paper reports the test results (in terms of the load-carrying capacities and bracing forces) of a large-scale bridge of twin I-girder type in which the location of the intermediate cross beam was varied across the depth of the main girders. Moreover, extensive numerical investigations were performed to study the effects of some relevant shape of imperfections on both the load-carrying capacities of the studied bridges and the magnitude of bracing forces generated in the cross beams that were involved. The test results showed that the load-carrying capacity of steel girders can exceed their lowest theoretical eigenvalue because of the presence of initial imperfections. In the finite-element analyses of the studied bridge cases, in some cases, the girders followed their shape of geometric imperfections and reached a load value that was greater than the lowest eigenvalue of the systems.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support from The Lars Erik Lundbergs Stipendiestiftelse (Dnr 7/2013 and Dnr 2014/05) and the research grant from Byggrådet (Dnr 12/2012) to support the laboratory tests are gratefully acknowledged. The assistance received from M. Molnar (Division of Structural Engineering, Lund University, Sweden) and T. Helwig (Division of Structural Engineering, University of Texas, Austin, TX) is highly appreciated.
References
AASHTO. (2014). AASHTO LRFD bridge design specifications, 7th Ed., Washington, DC.
Abaqus/CAE [Computer software]. SIMULIA, Providence, RI.
AISC. (2010). Specification for structural steel buildings, Chicago.
Bažant, Z. P., and Xiang, Y. (1997). “Postcritical imperfection-sensitive buckling and optimal bracing of large regular frames.” J. Struct. Eng., 513–522.
Galambos, T. V., and Surovek, A. E. (2008). Structural stability of steel: concepts and applications for structural engineers, John Wiley & Sons, New York.
Helwig T. A., Yura, J. A., and Frank, K. H. (1993). “Bracing forces in diaphragms and cross frames.” Proc., Is Your Structure Suitably Braced? Conf., Structural Stability Research Council, Milwaukee, 129–137.
Lindgaard, E., Lund, E., and Rasmussen, K. (2010). “Nonlinear buckling optimization of composite structures considering ‘worst’ shape imperfections.” Int. J. Solids Struct., 47(22), 3186–3202.
Mehri, H. (2015). “Bracing of steel bridges during construction; Theory, full-scale tests and simulations.” Ph.D. thesis, Lund Univ., Lund, Sweden.
Mehri, H., and Crocetti, R. (2015). “End-warping bracing of steel bridges during construction.” J. Bridge Eng., 04015060.
Mehri, H., and Crocetti, R. (2016). “Scaffolding bracing of composite bridges during construction.” J. Bridge Eng., 04016088.
Mehri, H., Crocetti, R., and Gustafsson, P. Y. (2015). “Unequally spaced lateral bracings on compression flanges of steel girders.” Structures, 3, 236–243.
Pi, Y., and Trahair, N. (1994). “Nonlinear inelastic analysis of steel beam-columns, II: Applications.” J. Struct. Eng., 2062–2085.
Schafer, B., and Peköz, T. (1998). “Computational modeling of cold-formed steel: characterizing geometric imperfections and residual stresses.” J. Constr. Steel Res., 47(3), 193–210.
Swedish Standards Institute. (2005). “Eurocode 3: Design of steel structures—Part 1-1: General rules and rules for buildings.” EN 1993-1-1:2005, Stockholm, Sweden.
Swedish Standards Institute. (2009). “Eurocode 3: Design of steel structures—Part 2: Steel bridges.” SS-EN 1993-2:2006, Stockholm, Sweden.
Taylor, A. C., and Ojalvo, M. (1966). “Torsional restraint of lateral buckling.” J. Struct. Div., 92(2), 115–130.
Wang, L., and Helwig, T. (2005). “Critical imperfections for beam bracing systems.” J. Struct. Eng., 933–940.
Wang, L., and Helwig, T. (2008). “Stability bracing requirements for steel bridge girders with skewed supports.” J. Bridge Eng., 149–157.
Winter, G. (1960). “Lateral bracing of columns and beams.” Trans ASCE, 125(1), 807–826.
Yura, J. A. (2001). “Fundamentals of beam bracing.” Eng. J., 38(1), 11–26.
Yura J. A., and Li, G. (2002). “Bracing requirements for inelastic beams.” Proc., Annual Stability Conf.: Reports on Current Research Activities, Structural Stability Research Council, Seattle.
Yura, J. A., Phillips, B., Raju, S., and Webb, S. (1992). Bracing of steel beams in bridges, Center for Transportation Research, Bureau of Engineering Research, Univ. of Texas, Austin, TX.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Apr 4, 2016
Accepted: Jun 28, 2016
Published online: Aug 31, 2016
Published in print: Jan 1, 2017
Discussion open until: Jan 31, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.