Structural Performance and Strength Prediction of Steel-to-Concrete Box Girder Deck Transition Zone of Hybrid Steel-Concrete Cable-Stayed Bridges
Publication: Journal of Bridge Engineering
Volume 21, Issue 11
Abstract
Because a large longitudinal force exists in hybrid girder cable-stayed bridges due to the cable tension, its transfer mechanisms on the steel-concrete combination segment would be an important issue. In this study, experiments and theoretical analysis were conducted to characterize the longitudinal force transfer mechanisms of the steel-concrete combination segment in hybrid girder cable-stayed bridges. Five full-scale local structure specimens were designed and manufactured based on the original design of the steel-to-concrete transition zone according to a completed cable-stayed bridge in China. The specimens were subjected to monotonic loading and tested up to complete failure. The load-slip curves; stress distribution and failure modes, which varied with the thickness of the bearing plate; and the shear connector distribution were obtained. To simulate the test properly, calculation methods for predicting the shear connector capacity and corresponding load-slip curves were proposed based on the analysis and experimental results including headed studs and perfobond strip connectors. Thus, a finite-element model using a nonlinear spring to simulate the shear connectors was proposed and validated by the test. Force transfer mechanisms were analyzed, and load distributing between different components of this composite system were revealed. As a result, the load distributing mode could be used to instruct preliminary engineering design and the modeling method could be used to verify it.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors express their sincere gratitude for the financial support provided by the National Natural Science Foundation of China (grants 51138007 and 51229801).
References
Abaqus 6.9 [Computer software]. SIMULIA, Providence, RI.
Ahn, J. H., Lee, C. G., Won, J. H., and Kim, S. H. (2010). “Shear resistance of the perfobond-rib shear connector depending on concrete strength and rib arrangement.” J. Constr. Steel Res., 66(10), 1295–1307.
An, L., and Cederwall, K. (1996). “Push-out tests on studs in high strength and normal strength concrete.” J. Constr. Steel Res., 36(1), 15–29.
Cândido-Martins, J. P. S., Costa-Neves, L. F., and da S. Vellasco, P. C. G. (2010). “Experimental evaluation of the structural response of Perfobond shear connectors.” Eng. Struct., 32(8), 1976–1985.
CEN (European Committee for Standardization). (2005). “Design of composite steel and concrete structures, part 2: General rules and rules for bridges.” EN 1994-2, Eurocode 4, Brussels, Belgium.
Chen, K. L., Wang, J. Z., and An, Q. H. (2006). “Model tests on steel-concrete joining section of main girder of a cable-stayed bridge.” Chin. Civ. Eng. J., 39(3), 86–90 (in Chinese).
Costa-Neves, L. F., Figueiredo, J. P., da S. Vellasco, P. C. G., and da Cruz Vianna, J. (2013). “Perforated shear connectors on composite girders under monotonic loading: An experimental approach.” Eng. Struct., 56, 721–737.
Gattesco, N., and Giuriani, E. (1996). “Experimental study on stud shear connectors subjected to cyclic loading.” J. Constr. Steel Res., 38(1), 1–21.
He, J., Liu, Y., Chen, A., and Yoda, T. (2010). “Experimental study on inelastic mechanical behavior of composite girders under hogging moment.” J. Constr. Steel Res., 66(1), 37–52.
Hibbit, K. (2009). Abaqus theory and user manuals, version 6.9, SIMULIA, Providence, RI.
Hognestad, E., Hanson, N. W., and McHenry, D. (1955). “Concrete stress distribution in ultimate strength design.” ACI J., 27(4), 455–479.
Jianguo, N., Ying, T., and Hongquan, W. (1999). “Strength of stud shear connectors in composite steel-HC beams.” J. Tsinghua Univ., 39(12), 94–97 (in Chinese).
Kim, S. E., and Nguyen, H. T. (2010). “Finite element modeling and analysis of a hybrid steel-PSC beam connection.” Eng. Struct., 32(9), 2557–2569.
Kim, S. E., and Nguyen, H. T. (2012). “Evaluation of the connection efficiency of hybrid steel-concrete girder using finite element approach.” Int. J. Mech. Sci., 61(1), 8–23.
Kim, S. H., Lee, C. G., Kim, S. J., and Won, J. H. (2011). “Experimental study on joint of spliced steel-PSC hybrid girder, part II: full scale test of spliced hybrid I-girder.” Eng. Struct., 33(9), 2668–2682.
Kurita, A., and Ohyama, A. (2003). “Recent steel–concrete hybrid bridges in Japan.” Int. J. Steel Struct., 3(4), 271–279.
Lam, D., and El-Lobody, E. (2005). “Behavior of headed stud shear connectors in composite beam.” J. Struct. Eng., 96–107.
Li, X. Z., Xiao, L., Zhang, X., and Liu, D. J. (2009). “Experimental research on bearing capacity of PBL shear connectors of steel-concrete joint in cable-stayed bridge.” Steel Constr., 24(9), 22–27 (in Chinese).
Lin, W., Teruhiko, Y., Nozomu, T., Hideyuki, K., and He, J. (2013). “Mechanical performance of steel-concrete composite beams subjected to a hogging moment.” J. Struct. Eng., 140(1), 04013031.
Loh, H. Y., Uy, B., and Bradford, M. A. (2004). “The effects of partial shear connection in the hogging moment regions of composite beams: Part I–Experimental study.” J. Constr. Steel Res., 60(6), 897–919.
Luo, Y. Z. (2008). “Research of headed studs in steel-concrete composite beam.” M.S. thesis, Central South Univ., Changsha, China (in Chinese).
MOHURD (Ministry of Housing and Urban-Rural Development). (2003). “Code for design of concrete structures.” GB 50017-2003, Beijing (in Chinese).
Oehlers, D. J., and Coughlan, C. G. (1986). “The shear stiffness of stud shear connections in composite beams.” J. Constr. Steel Res., 6(4), 273–284.
Oguejiofor, E. C., and Hosain, M. U. (1997). “Numerical analysis of push-out specimens with perfobond rib connectors.” Comput. Struct., 62(4), 617–624.
Oliveira Pedro, J. J., and Reis, A. J. (2010). “Nonlinear analysis of composite steel–concrete cable-stayed bridges.” Eng. Struct., 32(9), 2702–2716.
Ollgaard, J. G., Slutter, R. G., and Fisher, J. W. (1971). “The strength of stud shear connection in lightweight and normal-weight concrete.” AISC Eng. J., 8(2), 55–64.
Roeder, C. W., Cameron, B., and Brown, C. B. (1999). “Composite action in concrete filled tubes.” J. Struct. Eng., 477–484.
Rovnak, M., and Duricova, A. (2004). “Behaviour evaluation of shear connection by means of shear-connection strips.” Steel Compos. Struct., 4(3), 247–263.
Soty, R., and Shima, H. (2013). “Formulation for shear force-relative displacement relationship of L-shape shear connector in steel-concrete composite structures.” Eng. Struct., 46, 581–592.
Virlogeux, M. (1999). “Recent evolution of cable-stayed bridges.” Eng. Struct., 21(8), 737–755.
Xiao, L. (2012). “Study of static and fatigue behavior of PBL shear connectors in steel-concrete composite structure.” Ph.D. thesis, Southwest Jiaotong Univ., Chengdu, China (in Chinese).
Xue, D., Liu, Y., and Zhen, Y. (2012). “Static behavior of multi-stud shear connectors for steel-concrete composite bridge.” J. Constr. Steel Res., 74(7), 1–7.
Xue, W., Ding, M., Wang, H., and Luo, Z. (2008). “Static behavior and theoretical model of stud shear connectors.” J. Bridge Eng., 623–634.
Zhang, Z. X., Huang, C. P., and Xu, H. Y. (2010). “Force transfer mechanism for steel-concrete composite structures of hybrid cable-stayed bridges.” J. Huazhong Univ. Sci. Technol. (Nat. Sci. Ed.), 38(5), 117–120 (in Chinese).
Zhou, H. (2005). “Research and model test of shear connectors in the steel-concrete composite segment of the 3rd Nanjing Yangtze River Bridge’s tower.” M.S. thesis, Southwest Jiaotong Univ., Chengdu, China (in Chinese).
Zong, Z. H., and Che, H. M. (1999). “Experimental research for shear connectors static and fatigue behavior.” J. Fuzhou Univ. (Nat. Sci.), 27(6), 61–66 (in Chinese).
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Nov 23, 2015
Accepted: May 10, 2016
Published online: Jun 27, 2016
Published in print: Nov 1, 2016
Discussion open until: Nov 27, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.