Nontraditional Shear Failures in Bulb-T Prestressed Concrete Bridge Girders
Publication: Journal of Bridge Engineering
Volume 21, Issue 7
Abstract
An experimental study was conducted in which five identical, full-scale bulb-T bridge girders were constructed and tested to shear failure. Although the shear span was kept the same for all of the tests (a = 3d), the distance from the end of the specimen to the center of the support bearing (overhang length) was varied. Varying the overhang length controlled whether or not the critical section subject to shear fell within the transfer length, which affected whether the specimen failure was caused by a traditional shear mechanism (web crushing, flexure-shear, etc.) or a nontraditional shear mechanism (e.g., horizontal shear or shear failure induced by anchorage zone distress). The shear failure values were compared with each other to investigate whether nontraditional shear mechanisms result in a lower capacity than traditional mechanisms. These values were also compared with nominal design capacities related to each different failure mechanism.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank B. Stasney, A. Valentine, D. Fillip, D. Braley, and the rest of the support staff at the Ferguson Structural Engineering Laboratory for their assistance during testing of these specimens.
References
AASHTO. (2012). AASHTO LRFD bridge design specification, customary U.S. units, 6th Ed., Washington, DC.
ACI (American Concrete Institute). (2014). Building code requirements for structural concrete (ACI 318-14) and commentary, Farmington Hills, MI.
ASTM. (2008). “Standard specification for deformed and plain carbon-steel bars for concrete reinforcement, grade.” ASTM A615/A615M, West Conshohocken, PA.
Avendano, A. (2011). “Pretensioned box beams: Prestress transfer and shear behavior.” Ph.D. dissertation, Center for Transportation Research, Univ. of Texas, Austin, TX.
Avendano, A. R., and Bayrak, O. (2008). “Shear strength and behavior of prestressed concrete beams.” Technical Rep. IAC-88-5DD1A003-3, Center for Transportation Research, Univ. of Texas, Austin, TX, 180.
Avendano, A. R., and Bayrak, O. (2011). “Efficient shear reinforcement design limits for prestressed concrete beams.” ACI Struct. J., 108(6), 689–697.
Birrcher, D. B., Bayrak, O., and Kreger, M. E. (2010). “Effects of increasing allowable compressive stress at prestress transfer.” ACI Struct. J., 107(S03), 21–31.
FDOT (Florida Department of Transportation). (2012). Index 20010 series prestressed Florida-I beams, Tallahassee, FL.
Garber, D., Gallardo, J., Deschenes, D., Dunkman, D., and Bayrak, O. (2012). “Effect of new prestress loss estimates on pretensioned concrete bridge girder design.” Rep. No. FHWA/TX-12/0-6374-2, Center for Transportation Research, Univ. of Texas, Austin, TX.
Hawkins, N. M., and Kuchma, D. A. (2007). Application of LRFD bridge design specifications to high-strength structure concrete: shear provisions, Transportation Research Board, Washington, DC, 206.
Hovell, C., Avendano, A., Moore, A., Dunkman, D., Bayrak, O., and Jirsa, J. (2013). “Structural performance of Texas U-Beams at prestress transfer and under shear-critical loads.” Rep. No. FHWA/TX-13/0-5831-2, Center for Transportation Research, Univ. of Texas, Austin, TX, 355.
Hoyer, E., and Friedrich, E. (1939). “Beitrag zur frage der haftspannung in eisenbetonbauteilen.” Beton und Eisen, 50(9), 717–736.
Langefeld, D. P. (2012). “Anchorage-controlled shear capacity of prestressed concrete bridge girders.” M.Sc. thesis, Univ. of Texas, Austin, TX.
Ma, Z., Tadros, M. K., and Baishya, M. (2000). “Shear behavior of pretensioned high-strength concrete bridge I-girders.” ACI Struct. J., 97(1), 185–192.
Nakamura, E., Avendano, A. R., and Bayrak, O. (2013). “Shear database for prestressed concrete members.” ACI Struct. J., 110(S73), 909–918.
Ross, B. E., Hamilton, H., and Consolazio, G. R. (2014). “Experimental study of end region detailing and shear behavior of concrete I-girders.” J. Bridge Eng., 04014087.
Russell, B. W., and Burns, N. H. (1993). “Design guidelines for transfer, development and debonding of large diameter seven wire strands in pretensioned concrete girders.” Rep. No. FHWA/TX-93 + 1210-5F, Center for Transportation Research, Univ. of Texas, Austin, TX, 471.
Shahawy, M., and Cai, C. (2001). “Enhancement of the performance of prestressed concrete using strand anchorage.” PCI J., 46(5), 82–96.
TxDOT (Texas Department of Transportation). (2005). “Bridge standards.” 〈http://www.txdot.gov/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm〉 (Jan. 11, 2015).
TxDOT (Texas Department of Transportation). (2007). “Bridge standards.” 〈www.txdot.gov/insdtdot/orgchart/cmd/cserve/standard/bridge-e.htm〉 (Jan. 11, 2015).
TxDOT (Texas Department of Transportation). (2014). Bridge standards, Austin, TX.
Wesson, M. D. (2013). “Influence of strand debonding on the shear strength of prestressed concrete.” Ph.D. thesis, Purdue Univ., West Lafayette, IN.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Jul 28, 2015
Accepted: Nov 5, 2015
Published online: Feb 3, 2016
Published in print: Jul 1, 2016
Discussion open until: Jul 3, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.