Short-Term Elongation Variation of Posttensioned Tendons
Publication: Journal of Bridge Engineering
Volume 20, Issue 11
Abstract
When tension is applied to steel tendons, they elongate in proportion to the tensile force, as predicted by Hooke’s law. This elongation is used by the South African standard on concrete structural works and the South African standard specification for road and bridgeworks to determine the adequacy of the force applied in a tendon. The standards prescribe an elongation variation limit of and an average elongation variation limit of . According to these standards, if the elongation variation of the tendon falls outside these prescribed limits, it must be brought to the attention of the engineer. The scatter of tendon elongation results is often greater than the range prescribed by these standards. This usually requires the contractor to retension the tendons at huge financial costs. In most cases, the results obtained after retensioning are the same. This paper analyzes tensioning data obtained from a variety of projects that have been completed in South Africa in recent years. The aim of this investigation is to determine the causes of variation in elongation and suggest adjustments, if any, to the current elongation variation.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The author wishes to thank Mr. Sebastian Rupiper, who collected the data reported in this paper during his vacation work.
References
AASHTO. (2012). Bridge design specification, 6th Ed., Washington, DC.
AASHTO. (2014). Bridge construction specification, 3rd Ed., Washington, DC.
ACI (American Concrete Institute). (2011). “Building code requirements for structural concrete and commentary.” ACI 318-11, Farmington Hills, MI.
BSI (British Standard Institution). (2012). “Specification for high tensile steel wire and strand for the pre-stressing of concrete.” BS 5896, London.
Cement and Concrete Association. (1979). “Loss of prestress.” 2P/19/1 (43), Concrete Society, U.K.
CEN (European Committee for Standardization). (2004a). “Design of concrete structures, Part 1-1: General rules and rules for buildings.” EN 1992-1-1, Brussels, Belgium.
CEN (European Committee for Standardization). (2004b). “Mechanical tests for posttensioning systems.” EN 13391, Brussels, Belgium.
COLTO (Committee of Land and Transport Officials). (1998). Standard specification for road and bridge works, Department of Transport, South Africa.
Concrete Society of Southern Africa. (1992). Unbonded single strand tendons: Recommended specifications, Committee of the Prestressed Concrete Division, South Africa.
EOTA (European Organisation for Technical Approvals). (2007). “Post-tensioning kit for prestressing of structures.” ETA-06/0226, Brussels, Belgium.
EN (European Norms). (1986). “Pre-stressing steels.” Euronorm 138-79, Standardization Offices of the European Communities’ Member States, Iron and Steel Nomenclature Co-ordination Committee, Luxembourg.
FIB (Fédération internationale du béton/International Federation for Structural Concrete). (2010). Model code for concrete structures, Ernst & Sohn, Berlin.
FIP (International Federation for Prestressing). (1986). Tensioning of tendons: Force-elongation relationship, Thomas Telford, London.
Freyermuth, C. (1991). “Rational application of the elongation tolerance for post tensioning tendons.” ACI Struct. J., 88(S75), 730–737.
Kruger, P. P. (2012). Over-elongation report for Jean Avenue and John Vorster Drive viaduct, Bombela, Johannesburg, South Africa.
Longbottom, K. W. (1985). Committee correspondence, Euronorm Committee for Prestressing steels, London.
PTI (Post-Tensioning Institute). (2006). Post-tensioning manual, 6th Ed., Phoenix, AZ.
Preston, H. K. (1985). “Testing 7-wire strand for prestressed concrete—the state of the art.” J. Pre-stress. Concr. Inst., 30(3), 134–155.
Russell, L., and Price, P. E. (2007). Field elongation measurements, Post-Tensioning Institute, Phoenix, AZ, 6.
SANS (South African National Standards). (2000). “Standardised specification for the structural use of concrete.” SANS 10100-1, Pretoria, South Africa.
SANS (South African National Standards). (2007). “Construction works— Part CC1: Concrete works (structural).” SANS 2001-CC1, Pretoria, South Africa.
Information & Authors
Information
Published In
Journal of Bridge Engineering
Volume 20 • Issue 11 • November 2015
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jul 24, 2014
Accepted: Nov 12, 2014
Published online: Apr 15, 2015
Discussion open until: Sep 15, 2015
Published in print: Nov 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.