Seismic Resistance of Socket Connection between Footing and Precast Column
Publication: Journal of Bridge Engineering
Volume 18, Issue 9
Abstract
A new concept has been developed for connecting spread footings and precast columns in bridges. The socket connection is constructed by precasting the column, erecting it, and casting the reinforced concrete footing around it. This system saves construction time on site because, in little more than the time needed to construct the footing, both the column and footing can be constructed. Site erection is facilitated by the fact that the field tolerances are essentially unlimited. The longitudinal column bars are straight and are terminated with mechanical anchors. This arrangement improves constructability, because no bars cross the interface between the column and footing, and it provides better transfer of forces in the connection region than is possible with conventional bent-out longitudinal bars. The surface of the column is roughened to improve adhesion to the surrounding cast-in-place concrete. Axial-load tests demonstrated that the connection can resist column axial loads far above those expected in practice. Cyclic, lateral-load tests demonstrated that the seismic performance of the connection is at least as good as, if not better than, that of a comparable cast-in-place system. The recent deployment of the new system in a highway overpass provided both field experience and initial estimates of the potential time savings.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was supported by the Federal Highway Administration (FHWA) (Grant No. DTFH61-09-G-00005), and by the Valle Foundation of the University of Washington. This work would not have been possible without valuable assistance of Dr. Bijan Khaleghi, Mr. Jugesh Kapur, and Mr. Eric Schultz of the WSDOT, Dr. Lee Marsh of Berger/ABAM Engineers, Mr. Steve Seguirant of Concrete Technology Corporation, and the staff of Tri-State Construction. The support of all of them is gratefully acknowledged.
References
AASHTO. (2009a). AASHTO guide specification for LRFD seismic bridge design (2009 interim revisions), Washington, DC.
AASHTO. (2009b). LRFD bridge design specifications, 4th Ed., Washington, DC.
American Concrete Institute (ACI). (2008). “Building code requirements for structural concrete and commentary.” ACI 318-08, Farmington Hills, MI.
Berry, M. P., and Eberhard, M. O. (2003). “Performance models for flexural damage in reinforced concrete columns.” Rep. 2003/18, Pacific Earthquake Engineering Research Center, Univ. of California, Berkeley, CA.
Berry, M. P., and Eberhard, M. O. (2004). “PEER structural performance database user’s manual.” Rep. 2004, Pacific Earthquake Engineering Research Center, Univ. of California, Berkeley, CA 〈www.ce.washington.edu/∼peeral〉 (Jan. 12, 2011).
Building Seismic Safety Council (BSSC). (2004). NEHRP recommended provisions for seismic regulations and for new buildings and other structures (FEMA 450), 2003 Ed., Washington, DC.
California DOT (CalTrans). (2006). “Seismic design criteria, Ver. 1.4,” Sacramento, CA.
Federal Highway Administration (FHWA). (2008). 2008 Condition and performance report, USDOT, Washington, DC.
Haraldsson, O. S., Janes, T. M., Eberhard, M. O., and Stanton, J. F. (2012). Laboratory tests of column-to-footing socket connections, USDOT, FWHA, Washington, DC.
Marsh, L. M., Wernli, M., Garrett, B. E., Stanton, J. F., Eberhard, M. O., and Weinert, M. D. (2011). “Application of accelerated bridge construction connections in moderate-to-high seismic regions.” Rep. 698, National Cooperative Highway Research Program (NCHRP), Transportation Research Board, Washington, DC.
Matsumoto, E. (2009). “Emulative precast bent cap connections for seismic regions: Grouted duct and cap pocket test results, design and construction specifications, design examples, and connection details.” ECS Rep. No. ECS-CSUS-2009-05, California State Univ., Sacramento, CA.
Matsumoto, E., Waggoner, M., Kreger, M., Vogel, J., and Wolf, L. (2008). “Development of a precast concrete bent-cap system.” PCI J., 53(3), 74–99.
Matsumoto, E., Waggoner, M., Sumen, G., Kreger, M., Wood, S., and Breen, J. (2001). “Development of a precast bent cap system.” Research Project 0-1748, Center for Transportation Research, Univ. of Texas at Austin, Austin, TX.
Osanai, Y., Watanabe, F., and Okamoto, S. (1996). “Stress transfer mechanism of socket base connections with precast concrete columns.” ACI Struct. J., 93(May-June), 266–276.
Pang, J. B. K., Eberhard, M. O., and Stanton, J. F. (2010). “Large-bar connection for precast bridge bents in seismic regions.” J. Bridge Eng., 15(3), 231–239.
Pang, J. B. K., Steuck, K., Cohagen, L. S., Stanton, J. F., and Eberhard, M. O. (2008). “Rapidly constructable large-bar precast bridge-bent seismic connection.” Rep. No. WA-RD 684.2, Washington State DOT, Washington State Transportation Research Center, Seattle.
Restrepo, J., Matsumoto, E., and Tobolski, M. (2011). “Development of precast bent cap systems for seismic regions.” Rep. 681, National Cooperative Highway Research Program (NCHRP), Transportation Research Board, Washington, DC.
Saunders, T. D., Cahill, J. A., McLean, D. I., Marsh, L. M., and Ho, C. (1995). “Seismic retrofitting of bridge substructures.” Transportation Research Record No. 1476, Transportation Research Board, Washington, DC, 37–47.
Steuck, K., Pang, J. B. K., Stanton, J. F., and Eberhard, M. O. (2007). “Anchorage of large bars in grouted ducts.” Rep. WA-RD 684.1, Washington State Transportation Research Center, Seattle.
Steuck, K., Stanton, J. F., and Eberhard, M. O. (2009). “Anchorage of large-diameter reinforcing bars in ducts.” ACI Struct. J., 106(July-August), 506–513.
Tobolski, M. J. (2010). “Improving the design and performance of concrete bridges in seismic regions.” Ph.D. thesis, Univ. of California, San Diego.
Washington State DOT (WSDOT). (2008). Bridge design manual, ver. M23-50.02, Olympia, WA.
Weinert, M. D. (2011). “Substructure connections for accelerated bridge construction in seismic regions.” M.S.C.E. thesis, Univ. of Washington, Seattle.
Xiao, Y., Priestley, M. J. N., and Seible, F. (1996). “Seismic assessment and retrofit of bridge column footings.” ACI Struct. J. 93(1), 79–94.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 24, 2012
Accepted: Jul 17, 2012
Published online: Aug 15, 2013
Published in print: Sep 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.