Imaging Tools for Evaluation of Gusset Plate Connections in Steel Truss Bridges
Publication: Journal of Bridge Engineering
Volume 18, Issue 5
Abstract
After the collapse of the Interstate 35W Bridge in Minneapolis, Minnesota, in 2007, transportation agencies began evaluating and rating their inventories of gusset plate connections. Connection evaluations require accurate drawings that detail the plate, member, and fastener geometries. These structural details should also accurately reflect the as-built conditions. For some connections, as-built information may not be available, or the available drawings may not represent the actual field conditions. To fill this gap, a new methodology was developed that enables rapid and accurate collection of field measurements for connection plate geometry. The method uses close-range photogrammetry techniques to rectify images taken with consumer-grade cameras using flat-field and fish-eye lenses. The technique has been demonstrated on full-scale gusset plates in the laboratory and in the field. Dimensional measurements from the processed images provided results that are as good as or better than conventional field measurements and with tolerances below what most engineers require for calculation of gusset plate connection capacity. This technique provides a new tool for bridge engineers to quickly collect gusset plate geometry that can be used in connection evaluations and rating and can further enhance bridge-management tasks.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by the Oregon Department of Transportation. The input and support of Bert Hartman, Jonathan Rooper, Jeff Swanstrom, Richard Groff, and Steven Soltesz were greatly appreciated. Quang Nguyen and Jason Killian of Oregon State University provided assistance during early development of the image-processing algorithms. The findings, conclusions, and recommendations presented are those of the authors and do not necessarily reflect the views of the project sponsors or individuals acknowledged.
References
Abraham, S., and Forstner, W. (2005). “Fish-eye-stereo calibration and epipolar rectification.” ISPRS J. Photogramm. Remote Sens., 59(5), 278–288.
Arias, P., Ordóñez, C., Lorenzo, H., Herraez, J., and Armesto, J. (2007). “Low-cost documentation of traditional agro-industrial buildings by close-range photogrammetry.” Build. Environ., 42(4), 1817–1827.
Berman J. W., Wang, B., Olson, A. W., Roeder, C. W., and Lehman, D. E. (2011). “Rapid assessment of gusset plate safety in steel truss bridges.” J. Bridge Eng., 17(2), 221–231.
Criminisi, A., Reid, I., and Zisserman, A. (2000). “Single view metrology.” Int. J. Comput. Vis., 40(2), 123–148.
Dare, P. M., Hanley, H. B., Fraser, C. S., Riedel, B., and Niemeier, W. (2002). “An operational application of automatic feature extraction: The measurement of cracks in concrete structures.” Photogramm. Rec., 17(99), 453–464.
Federal Highway Administration (FHwA). (2009). “Load rating guidance and examples for bolted and riveted gusset plates in truss bridges.” Publication No. FHWA-IF-09-014, Washington, DC.
Fujita, Y., Mitane, Y., and Hamamoto, Y. (2006). “A method for crack detection on a concrete structure.” Proc., 18th Int. Conf. on Pattern Recognition, IEEE, Piscataway, NJ, 901–904.
Hao, S. (2010). “I-35 bridge collapse.” J. Bridge Eng., 15(5), 608–614.
Higgins, C., Senturk, A. E., and Turan, O. T. (2010a). “Comparison of block-shear and Whitmore section methods for load rating existing steel truss gusset plate connections.” J. Bridge Eng., 15(2), 160–171.
Higgins, C., Turan, O. T., and Connor, R. J. (2010b). “Rapid ranking procedures for gusset plate connections in existing steel truss bridges.” J. Bridge Eng., 15(5), 581–596.
Hutchinson, T. C., and Chen, Z. (2006). “Improved image analysis for evaluation concrete damage.” J. Comput. Civ. Eng., 20(3), 210–216.
Ito, A., Aoki, Y., and Hashimoto, S. (2002). “Accurate extraction and measurement of fine cracks from concrete block surface image.” Proc., 28th Annual Conf. of the Industrial Electronics Society, Vol. 3, IEEE, Piscataway, NJ, 2202–2207.
Lee, S., and Chang, L. (2005). “Digital image processing methods for assessing bridge painting rust defects and their limitations.” Proc., Int. Conf. on Computing in Civil Engineering 2005, ASCE, Reston, VA, 1–12.
Liu, Z., Forsyth, D. S., Marincak, A., and Vesley, P. (2006). “Automated rivet detection in the EOL image for aircraft lap joints inspection.” NDT&E Int., 39(6), 441–448.
MATLAB 7.11.0 (R2010b) [Computer software]. Natick, MA, MathWorks.
McCrea, A., Chamberlain, D., and Navon, R. (2002). “Automated inspection and restoration of steel bridges—A critical review of methods and enabling technologies.” Autom. Construct., 11(4), 351–373.
Minmao, L., Okazaki, T., Roberto, B., Schultz, A. E., and Galambos, T. V. (2010). “Nonlinear finite-element analysis of critical gusset plates in the I-35W bridge in Minnesota.” J. Struct. Eng., 137(1), 59–68.
Ray, S. F. (2002). Applied photographic optics: Lenses and optical systems for photography, film, video, electronic and digital imaging, 3rd Ed., Focal, Oxford, U.K.
Rodríguez, J., Martín, M. T., Arias, P., Ordóñez, C., and Herráez, J. (2008). “Flat elements on buildings using close-range photogrammetry and laser distance measurement.” Opt. Lasers Eng., 46(7), 541–545.
Schneider, D., Schwalbe, E., and Maas, H. G. (2009). “Validation of geometric models for fisheye lenses.” ISPRS J. Photogramm. Remote Sens., 64(3), 259–266.
Sinha, S. K., Fieguth, P. W. (2006). “Automated detection of cracks in buried concrete pipe images.” Automation in Constr., 15(1), 58–72.
Tommaselli, A., and Reiss, M. (2005). “A photogrammetric method for single image orientation and measurement.” Photogramm. Eng. Remote Sensing, 71(6), 727–732.
van den Heuvel, F. A. (1998). “3D reconstruction from a single image using geometric constraints.” ISPRS J. Photogramm. Remote Sens., 53(6), 354–368.
Yamaguchi, T., and Hashimoto, S. (2006). “Automated crack detection for concrete surface image using percolation model and edge information.” Proc., 32nd Annual Conf. of the IEEE Industrial Electronics Society, IEEE, Piscataway, NJ, 3355–3360.
Yamaguchi, T., and Hashimoto, S. (2009). “Fast crack detection method for large size concrete surface images using percolation based image processing.” Mach. Vis. Appl., 21(5), 797–809.
Yamaguchi, T., Nakamura, S., and Hashimoto, S. (2008). “An efficient crack detection method using percolation-based image processing.” Proc., 3rd IEEE Conf. on Industrial Electronics and Applications, IEEE, Piscataway, NJ, 1875–1880.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Sep 7, 2011
Accepted: Dec 6, 2011
Published online: Dec 8, 2011
Published in print: May 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.