Fatigue Behavior of Welded T-Joints with a CHS Brace and CFCHS Chord under Axial Loading in the Brace
Publication: Journal of Bridge Engineering
Volume 18, Issue 2
Abstract
The welded truss composed of circular hollow section (CHS) braces and concrete-filled circular hollow-section (CFCHS) chords is a new kind of structural system that has been increasingly applied in large span arch bridges in China. It is necessary to have a good knowledge of fatigue strength of the welded CHS-to-CFCHS joints for the design of this kind of composite bridge. This paper reports on a series of tests on welded CHS-to-CFCHS T-joints subjected to axial cyclic fatigue loading in the brace. Eleven joints were designed to investigate various influence factors such as different nondimensional geometric parameters of circular hollow sections and different concrete strength grades. The quality of welds connecting brace and chord members were examined using the magnetic particle and radiographic inspection methods. The conditions of hot spot stress at both the crown and saddle positions in brace and chord members were determined by means of linear and nonlinear extrapolation methods. During the fatigue testing process, the number of cycles relating to several stages of failure, the crack initiation positions, crack propagation patterns, and the final failure modes were recorded. Fatigue strength of the CHS-to-CFCHS T-joints was compared with that of CHS-to-CHS T-joints. It is concluded that the CHS-to-CFCHS T-joints have a much lower stress concentration factor and consequently have better fatigue strength than the CHS-to-CHS T-joints, when both kinds of joints have the same nondimensional geometrical parameters and same nominal stresses on the brace. The curves in the Comité International pour le Développement et l’Étude de la Construction Tubulaire guidelines used for CHS-to-CHS joints are not appropriate for the reliable fatigue assessment of CHS-to-CFCHS T-joints based on the current test data.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank the Natural Science Foundation of China for financially supporting the research in the paper through Grant No. 50478108.
References
American Bureau of Shipping (ABS). (2004). Guide for buckling and ultimate strength assessment for offshore structures, Houston.
American Petroleum Institute (API). (2005). Recommended practice for planning, designing and constructing fixed offshore platforms, 19th Ed., API Publishing Services, Washington, DC.
American Welding Society (AWS). (2004). “Structural welding code-steel.” AWS D1.1/1.1M, Miami.
American Welding Society (AWS). (2008). “Structural welding code-steel.” ANSI/AWS D1.1-08, Miami.
Back, J., Wardenier, J., and Kurobane, Y. (1984). “The fatigue behaviour of hollow section joints.” 2nd Int. Conf. on Welding of Tubular Structures, Boston, 419–430.
Chen, J., Chen, J., and Jin, W. L. (2010). “Experiment investigation of stress concentration factor of concrete-filled tubular T joints.” J. Construct. Steel Res., 66(12), 1510–1515.
Det Norske Veritas (DNV). (2005). “DNV recommended practice RP-C203.” Fatigue strength analysis of offshore of steel structures, Det Norske Veritas, Oslo, Norway.
Efthymiou, M. (1998). “Development of SCF formulae and generalized influence functions for use in fatigue analysis.” Proc., Offshore Tubular Joints Conf, UEG Offshore Research, Englefield Green, Surrey, U.K.
European Committee for Standardization (CEN). (1992). “Design of steel structures, part 1.1: General rules and rules for buildings.” Eurocode 3,Brussels, Belgium.
European Convention for Constructional Steelwork (ECCS). (1985): Recommendations for the fatigue design of steel structures, European Convention for Consructional Steelwork, Brussels, Belgium.
Gao, F., Shao, Y. B., and Gho, W. M. (2007). “Stress and strain concentration factors of completely overlapped tubular joints under lap brace IPB load.” J. Construct. Steel Res., 63(3), 305–316.
International Institute of Welding (IIW). (2000). Fatigue design procedures for welded hollow section joints, X. L. Zhao and J. A. Packer, eds., Abington, Cambridge, U.K.
Kibriya, T., and Iqbal, M. (2007). “Performance of blended cement SCC filled steel tubes for repair/rehabilitation of structural columns of buildings, bridges and deep foundations.” 10th Int. Conf. on Studies, Repairs and Maintenance of Heritage Architecture, Prague, 329–338.
Littlejohn, G. S., and Hughes, D. C. (1988). “Grouts and grouting for construction and repair of offshore structures: A summary report.” OTH 88 289, HMSO, 111–120.
Mashiri, F. R., and Zhao, X. L. (2010). “Square hollow section (SHS) T-joints with concrete-filled chords subjected to in-plane fatigue loading in the brace.” Thin-Walled Struct., 48(2), 150–158.
Mashiri, F. R., Zhao, X. L., and Grundy, P. (2004). “Stress concentration factors and fatigue behaviour of welded thin-walled CHS–SHS T-joints under in-plane bending.” Eng. Struct., 26(13), 1861–1875.
Ministry of Construction of China. (2001). “Code for acceptance of construction quality of steel structures.” GB50205-2001. Chin Planning Press, Beijing, China.
Nguyen, T. N., and Wahab, M. A. (1995). “A theoretical study of the effect of weld geometry parameters on fatigue crack propagation life.” Eng. Fract. Mech., Volume 51, Issue 1, May 1995, 1–18.
Puthli, R. S., de Koning, C. H. M., van Wingerde, A. M., Wardenier, J., and Dutta, D. (1989). “Fatigue strength of welded unstiffened RHS Joints in latticed structures and vierendeel girders.” Final Rep.—Part III, Evaluation for Design Rules: Stevin Rep. No. 25-6-89-36/A1, Stevin Laboratory, Delft Univ. of Technology, Delft, Netherlands.
Tong, L. W., Sun, C. Q., Chen, Y. Y., Zhao, X. L., Shen, B., and Liu, C. B. (2008). “Experimental comparison in hot spot stress between CFCHS and CHS K-joints with gap” Tubular structures XII, Z. Y. Shen, Y. Y. Chen, and X. Z. Zhao, eds., Taylor & Francis, London, 389–395.
van Wingerde, A. M. (1992). “The fatigue behaviour of T- and X-joints made of square hollow sections.” Heron, 37(2), 1–80.
van Wingerde, A. M., Packer, J. A., and Wardenier, J. (1995). “Criteria for the fatigue assessment of hollow structural section connections.” J. Construct. Steel Res., 35(1), 71–115.
Wang, K. (2008). “Study on the hot spot stress and fatigue strength of welded circular hollow section (CHS) T-joints with concrete-filled chords.” Ph.D. thesis, Tongji Univ., Shanghai, China.
Zhao, X. L., et al. (2001). Design guide for circular and rectangular hollow section welded joints under fatigue loading, U V Rheinland, Koln, Germany.
Zhao, X. L., Wilkinson, T., and Hancock, G. J. (2005). Cold-formed tubular members and connections, Elsevier, Oxford, U.K.
Zhu, J. (2007). “Fatigue behaviour of welded T-joints of concrete-filled circular hollow sections.” M.S. thesis, Tongji Univ., Shanghai, China.
Zhou, S., and Chen, S. (2003). “Rapid Development of CFST arch bridges in China,” Proc. Int. Conf. on Advances in Structures: Steel, Concrete, Composite and Aluminium, Vol. 2, Sydney, Australia, 915–920.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 13, 2011
Accepted: Oct 25, 2011
Published online: Oct 27, 2011
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.