Structural Batteries in Aviation: A Preliminary Sizing Methodology
Publication: Journal of Aerospace Engineering
Volume 33, Issue 4
Abstract
A significant research effort in aviation is currently focused on the integration of electric or hybrid-electric power-trains onboard aircraft in an effort to improve efficiency and environmental friendliness. New designs incorporating these novel propulsion systems face the issue of penalizing battery characteristics, especially in terms of limited energy and power density performance, in turn imposing a toll on the inert weight of the machine. A possible solution to this issue is that of structural batteries. These are similar in structure to carbon fiber composites, where the matrix features dielectric characteristics, making the structure capable of storing electric energy while retaining the capability to withstand mechanical loads. The adoption of this technology, currently under advanced development, shall enable significant weight savings; yet it also raises relevant issues concerning aircraft sizing procedures that need to be conceived taking into account the specific characteristics of such multifunctional materials. This paper faces the new problem of aircraft initial design in presence of structural batteries. First, it presents a method for aircraft preliminary weight sizing, where the double effect of structural batteries on both structural mass and energy storage mass is considered. Subsequently, a procedure to size an airframe structure with the adoption of structural batteries in key components is shown, based on a weight-optimal approach. The complete sizing procedure is illustrated through an award-winning test case in the General Aviation category.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data produced and used in the presented case study are available from the corresponding author by request (not included herein for obvious reasons of length limitations).
Acknowledgments
The contribution of A. Bernasconi, L. Capoferri, A. Favier, C. Velarde Lopez de Ayala, and F. Gualdoni of the Department of Aerospace Science and Technology, Politecnico di Milano in the obtainment of the results is gratefully acknowledged. The insight provided by E. D. Wetzel, Ph.D., of the US Army Research Laboratory on the technology of structural batteries has been instrumental in the design of the proposed procedure and in analyzing results in the considered test case.
References
Adam, T. J., G. Liao, J. Petersen, S. Geier, B. Finke, P. Wierach, A. Kwade, and M. Wiedemann. 2018. “Multifunctional composites for future energy storage in aerospace structures.” Energies 11 (2): 335. https://doi.org/10.3390/en11020335.
Allen, H. G. 1969. Analysis and design of structural sandwich panels. Oxford, UK: Pergamon Press.
Ampaire, Inc. 2020. “3507 Jack Northrop Ave., Hawthorne, CA 90250, USA.” Accessed March 25, 2020. www.ampaire.com.
Asp, L. E. 2013. “Multifunctional composite materials for energy storage in structural load paths.” Plast. Rubber Compos. 42 (4): 144–149. https://doi.org/10.1179/1743289811Y.0000000043.
Asp, L. E., and E. S. Greenhalgh. 2014. “Structural power composites.” Compos. Sci. Technol. 101 (Sep): 41–61. https://doi.org/10.1016/j.compscitech.2014.06.020.
Bernasconi, A., F. Biondani, L. Capoferri, A. Favier, C. Velarde Lopez de Ayala, C. E. D. Riboldi, and L. Trainelli. 2017. “Conceptual design of a structural-battery hybrid-electric aircraft.” In Proc., 24th Conf. of the Italian Association of Aeronautics and Astronautics (AIDAA 2017). Rome: Italian Association of Aeronautics and Astronautics.
Bona, G. E., M. Bucari, A. Castagnoli, and L. Trainelli. 2014. “Flybrid: Envisaging the future hybrid-powered regional aviation.” In Proc., AIAA/3AF Aircraft Noise and Emissions Reduction Symp. Reston, VA: American Institute of Aeronautics and Astronautics.
Botelho, E. C., R. A. Silva, L. C. Pardini, and M. C. Rezende. 2006. “A review on the development and properties of continuous fiber/epoxy/aluminum hybrid composites for aircraft structures.” Mater. Res. 9 (3): 247–256. https://doi.org/10.1590/S1516-14392006000300002.
Bruhn, E. F. 1973. Analysis and design of flight vehicle structures. Carmel, IN: Jacobs Publishing.
Cao, W., B. C. Mecrow, G. J. Atkinson, J. W. Bennett, and D. J. Atkinson. 2012. “Overview of electric motor technologies used for more electric aircraft (MEA).” IEEE Trans. Ind. Electron. 59 (9): 3523–3531. https://doi.org/10.1109/TIE.2011.2165453.
Carlstedt, D., E. Marklund, and L. E. Asp. 2019. “Effects of state of charge on elastic properties of 3d structural battery composites.” Compos. Sci. Technol. 169 (Jan): 26–33. https://doi.org/10.1016/j.compscitech.2018.10.033.
Cohen, J. P., and C. C. Coughlin. 2008. “Spatial hedonic models of airport noise; proximity and housing prices.” J. Reg. Sci. 48 (5): 859–878. https://doi.org/10.1111/j.1467-9787.2008.00569.x.
Diamond Aircraft Industries GmbH. 2020. “N. A. Otto-Strasse 5, 2700 Wiener Neustadt, Austria.” Accessed March 25, 2020. www.diamondaircraft.com.
Ekstedt, S., M. Wysocki, and L. E. Asp. 2010. “Structural batteries made from fibre reinforced composites.” Plast. Rubber Compos. 39 (3–5): 148–150. https://doi.org/10.1179/174328910X12647080902259.
Friedrich, C., and P. A. Robertson. 2015. “Hybrid-electric propulsion for aircraft.” J. Aircr. 52 (1): 176–189. https://doi.org/10.2514/1.C032660.
Gienger, E. B., P. A. T. Nguyen, W. Chin, K. D. Behler, J. F. Snyder, and E. D. Wetzel. 2015. “Microstructure and multifunctional properties of liquid + polymer bicomponent structural electrolytes: Epoxy gels and porous monoliths.” J. Appl. Polym. Sci. 132 (42). https://doi.org/10.1002/app.42681.
Gudmundsson, S. 2013. General aviation aircraft design. 1st ed. Oxford, UK: Butterworth-Heinemann.
Hagen, M., S. Dörfler, P. Fanz, T. Berger, R. Speck, J. Tübke, H. Althues, M. J. Hoffmann, C. Scherr, and S. Kaskel. 2013. “Development and costs calculation of lithium–sulfur cells with high sulfur load and binder free electrodes.” J. Power Sources 224 (Feb): 260–268. https://doi.org/10.1016/j.jpowsour.2012.10.004.
Hagen, M., D. Hanselmann, K. Ahlbrecht, R. Maca, D. Gerber, and J. Tübke. 2015. “Lithium-sulfur cells: The gap between the state-of-the-art and the requirements for high energy battery cells.” Adv. Energy Mater. 5 (16): 1401986. https://doi.org/10.1002/aenm.201401986.
Hill, R. 1950. The mathematical theory of plasticity. Oxford, UK: Oxford University Press.
Johannisson, W., N. Ihrner, D. Zenkert, M. Johansson, D. Carlstedt, L. E. Asp, and F. Sieland. 2018. “Multifunctional performance of a carbon fiber ud lamina electrode for structural batteries.” Compos. Sci. Technol. 168 (Nov): 81–87. https://doi.org/10.1016/j.compscitech.2018.08.044.
Lange Aviation GmbH. 2020. “Brüsseler Straße, 30 D–66482 Zweibrücken, Germany.” Accessed March 25, 2020. www.lange-aviation.com.
Lekhnitskii, S. G. 1968. Anisotropic plates. New York: Gordon and Breach Science Publishers.
Liu, P., E. Sherman, and A. Jacobsen. 2009. “Design and fabrication of multifunctional structural batteries.” J. Power Sources 189 (1): 646–650. https://doi.org/10.1016/j.jpowsour.2008.09.082.
Morrell, P., and C. Lu. 2000. “Aircraft noise social cost and charge mechanisms: A case study of Amsterdam Airport Schiphol.” Transp. Res. Part D 5 (4): 305–320. https://doi.org/10.1016/S1361-9209(99)00035-8.
Ozawa, K. 2009. Lithium ion rechargeable batteries. 1st ed. New York: Wiley-VCH.
Pearson, C., C. Thwaite, and N. Russel. 2004. “The use of small cell lithium-ion batteries for more satellite applications.” In Proc., 18th Annual AIAA/USU Conf. on Small Satellites. Reston, VA: American Institute of Aeronautics and Astronautics.
Pipistrel Vertical Solutions d.o.o. 2020. “Goriska Cesta 50a, SI–5270 Ajdovšcina, Slovenia.” Accessed March 25, 2020. www.pipistrel.si.
Rao, N. S., T. G. A. Simha, K. P. Rao, and G. V. V. R. Kumar. 2015. “Structural batteries, carbon composites are becoming competitive and cost effective.” Accessed March 25, 2020. https://www.infosys.com/engineering-services/white-papers/documents/carbon-composites-cost-effective.pdf.
Raymer, D. P. 2012. Aircraft design: A conceptual approach: AIAA education series. 5th ed. Reston, VA: American Institute of Aeronautics and Astronautics.
Riboldi, C. E. D. 2018. “An optimal approach to the preliminary weight sizing of small hybrid-electric aircraft.” Aerosp. Sci. Technol. 81 (Oct): 14–31. https://doi.org/10.1016/j.ast.2018.07.042.
Riboldi, C. E. D., and F. Gualdoni. 2016. “An integrated approach to the preliminary weight sizing of small electric aircraft.” Aerosp. Sci. Technol. 58 (Nov): 134–149. https://doi.org/10.1016/j.ast.2016.07.014.
Riboldi, C. E. D., F. Gualdoni, and L. Trainelli. 2018. “Preliminary weight sizing of light pure-electric and hybrid-electric aircraft.” Transp. Res. Procedia 29 (Jan): 376–389. https://doi.org/10.1016/j.trpro.2018.02.034.
Roskam, J. 2003. Airplane design (Part I–VII). 2nd ed. Lawrence, KS: Design, Analysis and Research Corporation.
Rossi, N., F. Salucci, C. E. D. Riboldi, A. Rolando, and L. Trainelli. 2018. “A general approach to the conceptual design of all-electric and hybrid-electric aircraft.” In Proc., Advanced Aircraft Efficiency in a Global Air Transport System Conf. (AEGATS 2018). Toulouse, France: Association Aéronautique et Astronautique de France.
Scholz, A. E., A. Hermanutz, and M. Hornung. 2018. “Feasibility analysis and comparative assessment of structural power technology in all-electric composite aircraft.” In Proc., Deutscher Luft- und Raumfahrtkongress. Bonn, Germany: Deutsche Gesellschaft für Luft- und Raumfahrt - Lilienthal-Oberth e.V.
Senokos, E., Y. Ou, J. J. Torres, F. Sket, C. Gonzalez, R. Marcilla, and J. J. Vilatela. 2018. “Energy storage in structural composites by introducing CNT fiber/polymer electrolyte interleaves.” Nat. Sci. Rep. 8 (1): 1–10. https://doi.org/10.1038/s41598-018-21829-5.
Snyder, J. F., R. H. Carter, and E. D. Wetzel. 2007. “Electrochemical and mechanical behavior in mechanically robust solid polymer electrolytes for use in multifunctional structural batteries.” Chem. Mater. 19 (15): 3793–3801. https://doi.org/10.1021/cm070213o.
Snyder, J. F., D. J. O’Brien, and E. D. Wetzel. 2016. “Structural batteries, capacitors and supercapacitors.” In Handbook of solid state batteries. Singapore: World Scientific.
Szabo, B., and I. Babuska. 1991. Finite elements analysis. New York: Wiley.
Trainelli, L., D. Comincini, F. Salucci, A. Rolando, and C. E. D. Riboldi. 2019a. “Sizing and performance of hydrogen-driven airplanes.” In Proc., 25th Int. Conf. on Italian Associations of Aeronautics and Astronautics (AIDAA). Rome: AIDAA.
Trainelli, L., and I. Perkon. 2019. “MAHEPA: A milestone-setting project in hybrid-electric aircraft technology development.” In Proc., More Electric Aircraft Conf. (MEA 2019). Berlin: IQPC GmbH.
Trainelli, L., N. Rossi, F. Salucci, C. E. D. Riboldi, and A. Rolando. 2019b. “Preliminary sizing and energy management of serial hybrid-electric airplanes.” In Proc., 25th Int. Conf. on Italian Associations of Aeronautics and Astronautics (AIDAA). Rome: AIDAA.
Tsai, S. W., and E. M. Wu. 1971. “A general theory of strength for anisotropic materials.” J. Compos. Mater. 5 (1): 58–80. https://doi.org/10.1177/002199837100500106.
Various Authors. 2015. Certification specifications and acceptable means of compliance for normal, utility, aerobatic and commuter category aeroplanes CS-23: Amendment 4. Brussels, Belgium: European Aviation Safety Agency.
Wang, C. T., and D. F. D. Santo. 1953. Buckling of sandwich cylinders under axial compression, torsion, bending, and combined loads. New York: College of Engineering, Research Division, New York Univ.
Wetzel, E. D. 2010. “Perspectives on multifunctional energy-storing structures.” In Proc., Air Force Office for Scientific Research Multifunctional Materials for Defense Workshop. Aberdeen Proving Ground, MD: U.S. Army Combat Capabilities Development Command.
Wong, E. L., D. M. Baechle, K. Xu, R. H. Carter, J. F. Snyder, and E. D. Wetzel. 2007. “Design and processing of structural composite batteries.” In Proc., SAMPE 2007 Symp. Diamond Bar, CA: SAMPE.
Yuneec Americas (USA). n.d. “5555 Ontario Mills Parkway, Ontario, CA 91764, USA.” Accessed March 25, 2020. www.yuneec.com.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Jul 2, 2019
Accepted: Jan 3, 2020
Published online: Apr 18, 2020
Published in print: Jul 1, 2020
Discussion open until: Sep 18, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.