KF-Based Multiscale Response Reconstruction under Unknown Inputs with Data Fusion of Multitype Observations
Publication: Journal of Aerospace Engineering
Volume 32, Issue 4
Abstract
Utilization of multitype measurements including local and global information for structural health monitoring (SHM) has typically outperformed that using solo-type measurements. However, in many practical situations, only partial measurements can be obtained. Therefore, multiscale response reconstruction at the key locations of interest where sensors are not available is required. The Kalman filter (KF) is a powerful tool for optimally estimating the unknown structural states. The classical KF technique is, however, not applicable when the external excitations are unknown. In this paper, a KF-based multiscale response reconstruction under unknown input (MSRR-UI) approach is proposed to circumvent the aforementioned limitations. Based on the principle of KF, an analytical recursive solution of the proposed approach is derived and given. By using a projection matrix, a revised version of the observation equation is obtained. Multitype measurements in a few locations are fused together for response reconstruction. The unknown loading is simultaneously estimated by least-squares estimation (LSE). The effectiveness of the proposed approach is demonstrated via several numerical examples.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support from National Natural Science Foundation of China (Grant No. 51708198). The support from Natural Science Foundation of Hunan Province (No. 2018JJ3054) and Fundamental Development Funds for Young Researchers of Hunan University (No. 531107050912) is also greatly appreciated.
References
Azam, S. E., E. Chatzi, and C. Papadimitriou. 2015. “A dual Kalman filter approach for state estimation via output-only acceleration measurements.” Mech. Syst. Signal Proc. 60–61 (Aug): 866–886. https://doi.org/10.1016/j.ymssp.2015.02.001.
Chatzi, E. N., and C. Fuggini. 2015. “Online correction of drift in structural identification using artificial white noise observations and an unscented Kalman filter.” Smart. Struct. Syst. 16 (2): 295–328. https://doi.org/10.12989/sss.2015.16.2.295.
Cho, S., J. W. Park, R. P. Palanisamy, and S. H. Sim. 2016. “Reference-free displacement estimation of bridges using Kalman filter-based multimetric data fusion.” J. Sens. 2016: 1–9. https://doi.org/10.1155/2016/3791856.
Erazo, K., and E. M. Hernandez. 2014. “A model-based observer for state and stress estimation in structural and mechanical systems: Experimental validation.” Mech. Syst. Signal Proc. 43 (1–2): 141–152. https://doi.org/10.1016/j.ymssp.2013.10.011.
Guo, X., C. Sun, and P. Wang. 2017. “Multi-rate cubature Kalman filter based data fusion method with residual compensation to adapt to sampling rate discrepancy in attitude measurement system.” Rev. Sci. Instrum. 88 (8): 085002. https://doi.org/10.1063/1.4997072.
He, J., Y. L. Xu, C. D. Zhang, and X. H. Zhang. 2015. “Optimum control system for earthquake-excited building structures with minimal number of actuators and sensors.” Smart. Struct. Syst. 16 (6): 981–1002. https://doi.org/10.12989/sss.2015.16.6.981.
Hernandez, E. M. 2013. “Optimal model-based state estimation in mechanical and structural systems: Optimal model-based state estimation.” Struct. Control. Health Monit. 20 (4): 532–543. https://doi.org/10.1002/stc.513.
Hu, R. P., Y. L. Xu, and S. Zhan. 2018. “Multi-type sensor placement and response reconstruction for building structures: Experimental investigations.” Earthquake Eng. Eng. Vibr. 17 (1): 29–46. https://doi.org/10.1007/s11803-018-0423-3.
Iliopoulos, A., R. Shirzadeh, W. Weijtjens, P. Guillaume, D. V. Hemelrijck, and C. Devriendt. 2016. “A modal decomposition and expansion approach for prediction of dynamic responses on a monopile offshore wind turbine using a limited number of vibration sensors.” Mech. Syst. Signal Proc. 68–69 (Feb): 84–104. https://doi.org/10.1016/j.ymssp.2015.07.016.
Jo, H., and B. F. Spencer. 2014. “Multi-metric model-based structural health monitoring.” In Proc., SPIE 9061, Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems 2014. Bellingham, WA: Society of Photo-Optical Instrumentation Engineers.
Khodabandeloo, B., D. Melvin, and H. Jo. 2017. “Model-based heterogeneous data fusion for reliable force estimation in dynamic structures under uncertainties.” Sensors 17 (11): 2656. https://doi.org/10.3390/s17112656.
Kim, K., J. Choi, J. Chung, G. Koo, I. Bae, and H. Sohn. 2018. “Structural displacement estimation through multi-rate fusion of accelerometer and RTK-GPS displacement and velocity measurements.” Measurement 130 (Dec): 223–235. https://doi.org/10.1016/j.measurement.2018.07.090.
Kim, K., J. Choi, G. Koo, and H. Sohn. 2016. “Dynamic displacement estimation by fusing biased high-sampling rate acceleration and low-sampling rate displacement measurements using two-stage Kalman estimator.” Smart. Struct. Syst. 17 (4): 647–667. https://doi.org/10.12989/sss.2016.17.4.647.
Kim, K., and H. Sohn. 2017. “Dynamic displacement estimation by fusing LDV and LiDAR measurements via smoothing based Kalman filtering.” Mech. Syst. Signal Proc. 82 (Jan): 339–355. https://doi.org/10.1016/j.ymssp.2016.05.027.
Lee, H., S. Kang, and S. Han. 2018. “Real-time optimal state estimation scheme with delayed and periodic measurements.” IEEE Trans. Ind. Electron. 65 (7): 5970–5978. https://doi.org/10.1109/TIE.2017.2774731.
Li, J., H. Hao, and Z. W. Chen. 2017. “Damage identification and optimal sensor placement for structures under unknown traffic-induced vibrations.” J. Aerospace Eng. 30 (2): B4015001. https://doi.org/10.1061/(ASCE)AS.1943-5525.0000550.
Li, J., and S. S. Law. 2011. “Substructural response reconstruction in wavelet domain.” J. Appl. Mech. 78 (4): 041010. https://doi.org/10.1115/1.4003738.
Liu, L., J. Zhu, Y. Su, and Y. Lei. 2016. “Improved Kalman filter with unknown inputs based on data fusion of partial acceleration and displacement measurements.” Smart. Struct. Syst. 17 (6): 903–915. https://doi.org/10.12989/sss.2016.17.6.903.
Maes, K., A. Iliopoulos, W. Weijtjens, C. Devriendt, and G. Lombaert. 2016. “Dynamic strain estimation for fatigue assessment of an offshore monopile wind turbine using filtering and modal expansion algorithms.” Mech. Syst. Signal Proc. 76–77 (Aug): 592–611. https://doi.org/10.1016/j.ymssp.2016.01.004.
Palanisamy, R. P., S. Cho, H. Kim, and S. H. Sim. 2015. “Experimental validation of Kalman filter-based strain estimation in structures subjected to non-zero mean input.” Smart. Struct. Syst. 15 (2): 489–503. https://doi.org/10.12989/sss.2015.15.2.489.
Papadimitriou, C., C. P. Fritzen, P. Kraemer, and E. Ntotsios. 2011. “Fatigue predictions in entire body of metallic structures from a limited number of vibration sensors using Kalman filtering.” Struct. Control. Health Monit. 18 (5): 554–573. https://doi.org/10.1002/stc.395.
Smyth, A., and M. Wu. 2007. “Multi-rate Kalman filtering for the data fusion of displacement and acceleration response measurements in dynamic system monitoring.” Mech. Syst. Signal Proc. 21 (2): 706–723. https://doi.org/10.1016/j.ymssp.2006.03.005.
Wan, H. P., and Y. Q. Ni. 2018a. “Bayesian modeling approach for forecast of structural stress response using structural health monitoring data.” J. Struct. Eng. 144 (9): 04018130. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002085.
Wan, H. P., and Y. Q. Ni. 2018b. “Bayesian multi-task learning methodology for reconstruction of structural health monitoring data.” Struct. Health Monitor. 144 (9): 1–12. https://doi.org/10.1177/1475921718794953.
Xu, Y. L., and J. He. 2017. Smart civil structures. Boca Raton, FL: CRC Press.
Xu, Y. L., X. H. Zhang, S. Y. Zhu, and S. Zhan. 2016. “Multi-type sensor placement and response reconstruction for structural health monitoring of long-span suspension bridges.” Sci. Bull. 61 (4): 313–329. https://doi.org/10.1007/s11434-016-1000-7.
Zhang, C. D., and Y. L. Xu. 2016. “Structural damage identification via multi-type sensors and response reconstruction.” Struct. Health Monitor. 15 (6): 715–729. https://doi.org/10.1177/1475921716659787.
Zhang, C. D., and Y. L. Xu. 2017. “Structural damage identification via response reconstruction under unknown excitation: Damage detection via response reconstruction under unknown excitation.” Struct. Control. Health Monitor. 24 (8): e1953. https://doi.org/10.1002/stc.1953.
Zhang, X. H., Y. L. Xu, S. Zhu, and S. Zhan. 2014. “Dual-type sensor placement for multi-scale response reconstruction.” Mechatronics 24 (4): 376–384. https://doi.org/10.1016/j.mechatronics.2013.05.007.
Zhang, X. H., S. Zhu, Y. L. Xu, and X. J. Homg. 2011. “Integrated optimal placement of displacement transducers and strain gauges for better estimation of structural response.” Int. J. Struct. Stab. Dyn. 11 (3): 581–602. https://doi.org/10.1142/S0219455411004221.
Zheng, Z., H. Qiu, Z. Wang, S. Luo, and Y. Lei. 2019. “Data fusion based multi-rate Kalman filtering with unknown input for on-line estimation of dynamic displacements.” Measurement 131 (Jan): 211–218. https://doi.org/10.1016/j.measurement.2018.08.057.
Zhu, S. Y., X. H. Zhang, Y. L. Xu, and S. Zhan. 2013. “Multi-type sensor placement for multi-scale response reconstruction.” Adv. Struct. Eng. 16 (10): 1779–1797. https://doi.org/10.1260/1369-4332.16.10.1779.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Nov 19, 2018
Accepted: Jan 17, 2019
Published online: Apr 12, 2019
Published in print: Jul 1, 2019
Discussion open until: Sep 12, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.