Alterations in Critical Radii of Bluntness of Shock Wave Boundary Layer Interaction
Publication: Journal of Aerospace Engineering
Volume 30, Issue 5
Abstract
Any configuration consisting of flat plate attached to a ramp experiences shock wave boundary layer interaction (SWBLI) at supersonic or hypersonic Mach numbers. This interaction can lead to flow separation at the ramp foot. In that case, its extent depends on the leading-edge radius of the plate. At a specific radius (inversion radius), the separation bubble size attains maximum value, and at particular leading-edge bluntness (equivalent radius), the length of the separation bubble becomes equal to that of the sharp leading-edge case. Values of these critical radii need to be evaluated for complete understanding of dynamics of SWBLI. Therefore, numerical simulations are carried out to estimate these values with change in freestream Mach number, wall temperature, and freestream stagnation enthalpy. Thicknesses of the high-entropy layer and boundary layer, along with wall pressure distribution, are considered for analyzing the influence of these parameters on the estimation of critical radii. The magnitudes of both the radii have been observed to increase with a decrease in Mach number and stagnation enthalpy. Freestream static and total temperatures are found to have dimensional dependence on the flow field for moderate leading-edge radii instead of their ratio. Therefore, present studies are useful in understanding and accessing the effect of freestream conditions and wall temperature on the values of critical radii.
Get full access to this article
View all available purchase options and get full access to this article.
References
Anderson, J. D. (2000). Hypersonic and high temperature gas dynamics, American Institute of Aeronautics and Astronautics, Reston, VA.
Bleilebens, M., and Olivier, H. (2006). “On the influence of elevated surface temperatures on hypersonic shock wave/boundary layer interaction at a heated ramp model.” Shock Waves, 15(5), 301–312.
Chapman, D. R., Kuehn, D. M., and Larson, H. K. (1957). “Investigation of separated flows in supersonic and subsonic streams with emphasis on the effect of transition.”, National Advisory Committee for Aeronautics, Moffett Field, CA.
Coët, M. (1993). “Experiments on shock wave/boundary layer interaction in hypersonic flow.” La Recherche Aerospatiale, 1, 61–74.
Dietz, G., and Hein, S. (1999). “Entropy-layer instabilities over a blunted flat plate in supersonic flow.” Phys. Fluids, 11(1), 7–9.
Ganesh, N., Shende, N. V., and Balakrishnan, N. (2009). “R-parameter: A local truncation error based adaptive framework for finite volume compressible flow solvers.” Comput. Fluids, 38(9), 1799–1822.
Holden, M. S. (1970). “Boundary-layer displacement and leading edge bluntness effects on attached and separated laminar boundary layers in a compression corner. I: Theoretical study.” AIAA J., 8(12), 2179–2188.
Holden, M. S. (1971). “Boundary-layer displacement and leading-edge bluntness effects on attached and separated laminar boundary layers in a compression corner. II: Experimental study.” AIAA J., 9(1), 84–93.
Hung, F. T., and Barnett, D. O. (1973). “Shockwave-boundary layer interference heating analysis.” 11th Aerospace Sciences Meeting, American Institute of Aeronautics and Astronautics, Reston, VA, 72–237.
John, B., and Kulkarni, V. (2014a). “Effect of leading edge bluntness on the interaction of ramp induced shock wave with laminar boundary layer at hypersonic speed.” Comput. Fluids, 96, 177–190.
John, B., and Kulkarni, V. (2014b). “Numerical assessment of correlations for shock wave boundary layer interaction.” Comput. Fluids, 90, 42–50.
John, B., Kulkarni, V. N., and Natarajan, G. (2014). “Shock wave boundary layer interactions in hypersonic flows.” Int. J. Heat Mass Trans., 70, 81–90.
Kubota, T., Lees, L., and Lewis, J. E. (1968). “Experimental investigation of supersonic laminar, two-dimensional boundary-layer separation in a compression corner with and without cooling.” AIAA J., 6(1), 7–14.
Marini, M. (1998). “Effects of flow and geometry parameters on shock-wave boundary-layer interaction phenomena.” 11th Aerospace Sciences Meeting, American Institute of Aeronautics and Astronautics, Reston, VA, 98–1570.
Needham, D., and Stollery, J. (1966). “Boundary layer separation in hypersonic flow.” 3rd and 4th Aerospace Sciences Meeting, American Institute of Aeronautics and Astronautics, Reston, VA.
Needham, D. A. (1965). “Laminar separation in hypersonic flow.” Ph.D. dissertation, Imperial College London, London.
Neuenhahn, T., and Olivier, H. (2006). “Influence of the wall temperature and the entropy layer effects on double wedge shock boundary layer interactions.” 14th AIAA/AHI Space Planes and Hypersonic Systems and Technologies Conf., American Institute of Aeronautics and Astronautics, Reston, VA, 8136.
Nithish Reddy, P., and Venkatasubbaiah, K. (2014). “Numerical investigations on development of scramjet combustor.” J. Aerosp. Eng., .
Reinartz, B. U., Ballmann, J., and Boyce, R. (2006). “Numerical investigation of wall temperature and entropy layer effects on double wedge shock/boundary layer interactions.” 14th AIAA/AHI Space Planes and Hypersonic Systems and Technologies Conf., American Institute of Aeronautics and Astronautics, Reston, VA, 8137.
Schulte, D., Henckels, A., and Neubacher, R. (2001). “Manipulation of shock/boundary-layer interactions in hypersonic inlets.” J. Propul. Power, 17(3), 585–590.
Shi, J., Xu, T., Schafer, S. R., and Chen, C. L. (2013). “Adaptive control of shock waves with a passively morphing layer for rotating blades.” J. Aerosp. Eng., .
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Mar 1, 2016
Accepted: Nov 30, 2016
Published online: Mar 17, 2017
Discussion open until: Aug 17, 2017
Published in print: Sep 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.