Investigation of 3D Grain Shape Characteristics of Lunar Soil Retrieved in Apollo 16 Using Image-Based Discrete-Element Modeling
Publication: Journal of Aerospace Engineering
Volume 28, Issue 4
Abstract
This paper describes three-dimensional (3D) grain shape characteristics of returned lunar soil (No. 60501) and its numerical simulation by using the image-based discrete-element method (DEM). First, the lunar soil sample was investigated by X-ray computed tomography (CT) at the SPring-8 facility. Next, the obtained grain shapes were modeled by an original technique based on a clumped sphere method. The CT images were processed by an originally developed image analysis, and 74 grains were identified. Based on their 3D shapes and intraparticle voids and cracks, the grains were classified into four categories: (1) agglutinate (ag), (2) breccia type A (brA), (3) breccia type B (brB), and (4) plagioclase (pl). The content ratio of each grain category favorably agreed with those reported in previous studies. The 3D shape indices, namely, the aspect, flatness, and elongation ratios; the Krumbein’s sphericity; and the newly proposed volume ratio to ellipsoid were computed for 74 grains. Evaluating the differences in grain shape among the four categories, it was found that ag grains were considerably more angular (irregular) than grains belonging to the other categories. The volumes of the internal voids and cracks in the four categories were also quantitatively evaluated. There is no production of ag grains on Earth because the atmosphere prevents micrometeorite impacts. Although the effect of ag grains on the bulk properties of lunar soil should be evaluated, mechanical experiments may damage the lunar soil grains. Thus, the authors used computer simulations via image-based DEM. The grain shapes were modeled by clumping 10 spheres in the image-based DEM simulations. The effect of ag content on the dynamic (angle of repose) and quasistatic (simple shear) behaviors of the grain assembly were evaluated in a series of image-based DEM simulations. In simulations of , , and , the specimens developed the largest angle of repose. In addition, it was found that the ag content primarily affects the bulk density compared with the shear strength. This work is important for understanding the mechanical properties of lunar soils because simulation methods offer a suitable alternative to mechanical experiments, which may damage the specimens.
Get full access to this article
View all available purchase options and get full access to this article.
References
3DEC. (2014). “3DEC.” 〈http://www.itascacg.com/software/3dec〉 (May 1, 2014).
Abedi, S., and Mirghasemi, A. A. (2011). “Particle shape consideration in numerical simulation of assemblies of irregularly shaped particles.” Particuology, 9(4), 387–397.
Andrade, J. E., Lim, K.-W., Avila, C. F., and Vlahinić, I. (2012). “Granular element method for computational particle mechanics.” Comput. Meth. Appl. Mech. Eng., 241–244, 262–274.
Basu, A., McKay, S., Griffith, S., and Nace, G. (1981). “Regolith maturation on the earth and moon with an example from Apollo 15.” Proc., 12th Lunar Planet. Science, Pergamon Press, New York, 433–449.
Cundall, P. (1988). “Formulation of a three-dimensional distinct element model. Part I. A scheme to detect and represent contacts in a system composed of many polyhedral blocks.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 25(3), 107–116.
Dobrohotoff, P., Azeezullah, S., Maggi, F., and Alonso-Marroquin, F. (2012). “Optimal description of two-dimensional complex-shaped objects using spheropolygons.” Granular Matter, 14(5), 651–658.
Duttine, A., Tatsuoka, F., Kongkitkul, W., and Hirakawa, D. (2008). “Viscous behavior of unbound granular materials in direct shear.” Soils Found., 48(3), 297–318.
EDEM. (2014). “EDEM software platform.” 〈http://www.dem-solutions.com/software/edem-software/〉 (May 1, 2014).
Favier, J., Abbaspour-Foud, M., and Kremmer, M. (2001). “Modeling nonspherical particles using multisphere discrete elements.” J. Eng. Mech., 971–977.
Favier, J., Abbaspour-Foud, M., Kremmer, M., and Raji, A. (1999). “Shape representation of axi-symmetric, non-spherical particles in discrete element simulation using multi-element particles.” Eng. Comput., 16(4), 467–480.
Garboczi, E. (2002). “Three-dimensional mathematical analysis of particle shape using X-ray tomography and spherical harmonics: Application to aggregates used in concrete.” Cem. Concr. Res., 32(10), 1621–1638.
Garcia, X., Latham, J. P., Xiang, J., and Harrison, J. P. (2009). “A clustered overlapping sphere algorithm to represent real particles in discrete element modelling.” Géotechnique, 59(9), 779–784.
Görz, H., White, W., Johnson, G., and Pearson, M. (1972). “CESEMI studies of Apollo 14 and 15 fines.” Proc., 3rd Lunar Sci. Conf., Vo. 3, The M.I.T. Press, Cambridge, MA, 3195–3200.
Görz, H., White, W., Roy, R., and Johnson, G. (1971). “Particle size and shape distributions of lunar fines by CESEMI.” Proc., 2nd Lunar Sci. Conf., Vol. 3, The M.I.T. Press, Cambridge, MA, 2021–2025.
Heiken, G. (1975). “Petrology of lunar soils.” Rev. Geophys. Space Phys., 13(4), 567–587.
Heiken, G. H., Vaniman, J. L., and French, B. M. (1991). Lunar sourcebook, Cambridge University Press, Cambridge, U.K.
Heywood, H. (1971). “Particle size and shape distribution for lunar fines sample 12057, 72.” Proc., 2nd Lunar Sci. Conf., Vol. 3, The M.I.T. Press, Cambridge, MA, 1989–2001.
Hogue, C. (1998). “Shape representation and contact detection for discrete element simulations of arbitrary geometries.” Eng. Comput., 15(3), 374–390.
Houck, K. J. (1982). “Petrologic variations in Apollo 16 surface soils.” J. Geophys. Res., 87(S01), A197–A209.
Ikeda, S., Nakano, T., and Nakashima, Y. (2000). “Three-dimensional study on the interconnection and shape of crystals in a graphic granite by X-ray CT and image analysis.” Mineral. Mag., 64(5), 945–959.
Jaffe, L. D. (1972). “Shear strength of lunar soil from oceanus procellarum.” Earth Moon Planets, 8(1–2), 58–72.
Kanamori, H., Udagawa, S., Yoshida, T., Matsumoto, S., and Takagi, K. (1998). “Properties of lunar soil simulant manufactured in Japan.” Proc., Space’98, ASCE, Reston, VA, 462–468.
Katagiri, J. (2012). “Three-dimensional grain shape characterization of sands by X-ray CT and its application to image-based DEM.” Ph.D. thesis, Univ. of Tsukuba, Japan (in Japanese).
Katagiri, J., Matsushima, T., Saomoto, H., Toyoda, M., and Yamada, Y. (2014). “Quantitative characterization of three-dimensional grain shapes by X-ray micro CT at SPring-8.” J. JSCE, Ser. C, in press.
Katagiri, J., Matsushima, T., and Yamada, Y. (2010a). “Simple shear simulation of 3D irregularly shaped particles by image-based DEM.” Granular Matter, 12(5), 491–497.
Katagiri, J., Matsushima, T., and Yamada, Y. (2010b). “Statistics on 3D particle shape of lunar soil (No. 60501) obtained by micro X-ray CT and its image-based DEM simulation.” Proc., Earth & Space 2010, ASCE, Reston, VA, 254–259.
Katagiri, J., Matsushima, T., and Yamada, Y. (2012). “DEM simulations for evaluating effects of sample preparation method on the shear behavior of granular materials.” J. JSCE, Ser. A2, 68(1), 67–77 (in Japanese).
Kordesh, K. (1983). “Comparative Fourier grain shape analysis of meteoritic breccias and lunar soils.” Lunar and Planetary Science XIV, Lunar and Planetary Science Institute, Houston, TX, 387–388.
Krumbein, W. C. (1941). “Measurement and geologic significance of shape and roundness of sedimentary particles.” J. Sediment. Petrol., 11(2), 64–72.
Latham, J.-P., Munjiza, A., Garcia, X., Xiang, J., and Guises, R. (2008). “Three-dimensional particle shape acquisition and use of shape library for DEM and FEM/DEM simulation.” Miner. Eng., 21(11), 797–805.
Lee, X., Dass, W., and Manzione, C. (1993). “Characterization of the internal microstructures of granular materials using computerized tomography.” Review of progress in quantitative nondestructive evaluation, D. Thompson and D. Chimenti, eds., Plenum Press, New York, 1675–1680.
Lees, G. (1964). “A new method for determining the angularity of particles.” Sedimentology, 3(1), 2–21.
Liggghts. (2014). “Liggghts open source discrete element method particle simulation code.” 〈http://www.cfdem.com/liggghts-open-source-discrete-element-method-particle-simulation-code〉 (May 1, 2014).
Lim, K.-W., and Andrade, J. E. (2014). “Granular element method for three-dimensional discrete element calculations.” Int. J. Numer. Anal. Methods Geomech., 38(2), 167–188.
Lin, C., and Miller, J. (2005). “3D characterization and analysis of particle shape using X-ray microtomography (XMT).” Powder Technol., 154(1), 61–69.
Lu, M., and McDowell, G. R. (2007). “The importance of modelling ballast particle shape in the discrete element method.” Granular Matter, 9(1–2), 69–80.
Matsushima, T. (2004). “3-D image-based discrete element modeling for irregularly-shaped grains.” Proc., 2nd Int. PFC Symp., Taylor & Francis, Oxford, U.K., 421–427.
Matsushima, T., Katagiri, J., Saiki, K., Tsuchiyama, A., Ohtake, M., Nakano, T., and Uesugi, K. (2008a). “3D particle characteristics of highland lunar soil (No. 60501) obtained by micro X-ray CT.” Proc., Earth & Space 2008, ASCE, Reston, VA, 1–8.
Matsushima, T., Katagiri, J., Uesugi, K., Tsuchiyama, A., and Nakano, T. (2009). “3-D shape characterization and image-based DEM simulation of lunar soil simulant FJS-1.” J. Aerosp. Eng., 15–23.
Matsushima, T., and Saomoto, H. (2002). “Discrete element modeling for irregularly-shaped sand grains.” Proc., Numerical Methods in Geotechnical Engineering, P. Mestat, ed., LCPC, Paris, 239–246.
Matsushima, T., Saomoto, H., Matsumoto, M., Toda, K., and Yamada, Y. (2003). “Discrete element simulation of an assembly of irregularly shaped grains: Quantitative comparison with experiments.” Electric Proc., 16th Engineering Mechanics Conf., ASCE, Reston, VA.
Matsushima, T., Uesugi, K., Nakano, T., and Tsuchiyama, A. (2008b). “Microstructural quantification of granular assembly studied by micro X-ray CT at SPring-8.” J. Appl. Mech. JSCE, 11, 507–515 (in Japanese).
McDowell, G., Li, H., and Lowndes, I. (2011). “The importance of particle shape in discrete-element modelling of particle flow in a chute.” Géotechnique Lett., 1(3), 59–64.
MechSys. (2014). “Mechanical systems: computing library for simulations in continuum and discrete mechanics.” 〈http://mechsys.nongnu.org/index.shtml〉 (May 1, 2014).
MiDi, G. D. R. (2004). “On dense granular flows.” Eur. Phys. J. E., 14(4), 341–365.
Mitchell, J. K., Houston, W. N., Scott, R. F., Costes, N. C., Carrier, W. D. I., and Bromwell, L. G. (1972). “Mechanical properties of lunar soil: Density, porosity, cohesion, and angle of internal friction.” Proc., 3rd Lunar Sci. Conf., The M.I.T. Press, Cambridge, MA, 3, 3235–3253.
Miura, K., Maeda, K., Furukawa, M., and Toki, S. (1998). “Mechanical characteristics of sands with different primary properties.” Soils Found., 38(4), 159–172.
Munjiza, A. (2004). The combined finite-discrete element method, Wiley, Chichester, U.K.
Nakata, Y., Kato, M., Hyodo, M., Hyde, A., and Murata, H. (2001). “One-dimensional compression behaviour of uniformly graded sand related to single particle crushing strength.” Soils Found., 41(2), 39–51.
Nezami, E. G., Hashash, Y. M. A., Zhao, D., and Ghaboussi, J. (2006). “Shortest link method for contact detection in discrete element method.” Int. J. Numer. Anal. Methods Geomech., 30(8), 783–801.
O’Sullivan, C. (2011). Particulate discrete element modelling: A geomechanics perspective, Spon Press, London.
Perko, H., Nelson, J., and Sadeh, W. (2001). “Surface cleanliness effect on lunar soil shear strength.” J. Geotech. Geoenviron. Eng., 371–383.
PFC3D. (2014). “PFC.” 〈http://www.itascacg.com/software/pfc〉 (May 1, 2014).
Rowe, P. W. (1962). “The stress-dilatancy relation for static equilibrium of an assembly of particles in contact.” Proc. R. Soc. London, Ser. A, 269(1339), 500–527.
Schofield, A., and Wroth, C. (1968). Critical state soil mechanics, McGraw-Hill, New York.
Scott, R. F. (1987). “Failure.” Géotechnique, 37(4), 423–466.
Spanne, P., Thovert, J. F., Jacquin, C. J., Lindquist, W. B., Jones, K. W., and Adler, P. M. (1994). “Synchrotron computed microtomography of porous media: Topology and transports.” Phys. Rev. Lett., 73(14), 2001–2004.
Terzaghi, K., and Peck, R. (1948). Soil mechanics in engineering practice, Wiley, New York.
Tsuchiyama, A., et al. (2011). “Three-dimensional structure of hayabusa samples: Origin and evolution of itokawa regolith.” Science, 333(6046), 1125–1128.
UDEC. (2014). “UDEC.” 〈http://www.itascacg.com/software/udec〉 (May 1, 2014).
Wadell, H. (1935). “Volume, shape and roundness of quartz particles.” J. Geol., 43(3), 250–280.
Wang, L., Park, J.-Y., and Fu, Y. (2007). “Representation of real particles for DEM simulation using X-ray tomography.” Constr. Build. Mater., 21(2), 338–346.
Williams, J., and Pentland, A. (1989). “Superquadric and modal dynamics for discrete elements in interactive design.” Proc., 1st U.S. Conf. on Discrete Element Methods, CSM Press, Golden, CO.
Willman, B. M., Boles, W. W., McKay, D. S., and Allen, C. C. (1995). “Properties of lunar soil simulant JSC-1.” J. Aerosp. Eng., 77–87.
Yerazunis, S., Cornell, S. W., and Wintner, B. (1965). “Dense random packing of binary mixtures of spheres.” Nature, 207(4999), 835–837.
Zingg, T. (1935). “Beiträg zur schotteanalysis.” Min. Petrog. Mitt. Schweiz, 15, 39–140 (in German).
Information & Authors
Information
Published In
Journal of Aerospace Engineering
Volume 28 • Issue 4 • July 2015
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Sep 24, 2013
Accepted: Mar 11, 2014
Published online: Jul 25, 2014
Discussion open until: Dec 25, 2014
Published in print: Jul 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.