Wind Design Procedures for Wood Roof Trusses of Low-Rise Structures
Publication: Journal of Architectural Engineering
Volume 26, Issue 3
Abstract
Wind design procedures for wood roof trusses of low-rise structures are evaluated in this paper using wind tunnel test data and two-dimensional finite-element frame models. The adequacy of the conventional and two alternative design procedures is determined by computing the combined stress index in the top chord and the reliability index, β conditioned on the occurrence of the design wind speed. For trusses with typical design dead loads and constructed with wood that exhibits a relatively low degree of variability in material design values, the results indicate that both the conventional and the alternative design procedures considered in this study meet a target reliability index equal to 3.0. Of the three procedures, replacing main wind force resisting system (MWFRS) loads on a chord segment with components and cladding (C&C) loads, while maintaining MWFRS loads on all other chord member segments, provides the closest match to the target β. For trusses constructed with wood that exhibits a relatively high degree of variability in material design values, the reliability index is lower for all design procedures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for this research was provided in part by the Insurance Institute for Business and Home Safety (IBHS) and by the University of Wyoming. The views expressed in this paper are those of the authors and do not necessarily reflect the views of those acknowledged.
References
Allen, T. M., A. S. Nowak, and R. J. Bathurst. 2005. Calibration to determine load and resistance factors for geotechnical and structural design. Transportation Research E-Circular E-C079. Washington, DC: Transportation Research Board.
ASCE. 2010. Minimum design loads for buildings and other structures. ASCE/SEI 7-10. Reston, VA: ASCE.
ASCE. 2017. Minimum design loads and associated criteria for buildings and other structures. ASCE/SEI 7-16. Reston, VA: ASCE.
AWC (American Wood Council). 2015a. National design specification (NDS) for wood construction. Leesburg, VA: AWC.
AWC (American Wood Council). 2015b. National design specification (NDS) supplement: Design values for wood construction. Leesburg, VA: AWC.
Breyer, D., K. Cobeen, K. Fridley, and D. Pollock. 2015. Design of wood structures-ASD/LRFD. 7th ed. New York: McGraw-Hill Education.
Bulleit, W. M., and J. L. Yates. 1991. “Probabilistic analysis of wood trusses.” J. Struct. Eng. 117 (10): 3008–3025. https://doi.org/10.1061/(ASCE)0733-9445(1991)117:10(3008).
Cramer, S. M., J. M. Drozdek, and R. W. Wolfe. 2000. “Load sharing effects in light-frame wood-truss assemblies.” J. Struct. Eng. 126 (12): 1388–1394. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:12(1388).
Duthinh, D., M. L. Gierson, and B. M. Phillips. 2017. “Pressure coefficients on components and cladding from wind tunnel tests.” In Proc., 13th Americas Conf. on Wind Engineering. 1–33. Gainesville, FL: University of Florida.
Ellingwood, B., T. V. Galambos, J. G. MacGregor, and C. A. Cornell. 1980. Development of a probability based load criterion for American National Standard A58: Building code requirements for minimum design loads in buildings and other structures, Vol. 13. Washington, DC: United States Dept. of Commerce, National Bureau of Standards.
Galambos, T. V., B. Ellingwood, J. G. MacGregor, and C. A. Cornell. 1982. “Probability based load criteria: Assessment of current design practice.” J. Struct. Div. 108 (5): 959–977.
Gavanski, E., B. Kordi, G. A. Kopp, and P. J. Vickery. 2013. “Wind loads on roof sheathing of houses.” J. Wind Eng. Ind. Aerodyn. 114: 106–121. https://doi.org/10.1016/j.jweia.2012.12.011.
Gierson, M. L., B. M. Phillips, and D. Duthinh. 2015. “Evaluation of ASCE 7-10 wind velocity pressure coefficients on the components and cladding of low-rise buildings using recent wind tunnel testing data.” In Proc., 6th Int. Conf. on Advances in Experimental Structural Engineering, and 11th Int. Workshop on Advanced Smart Materials and Smart Structural Technology. Urbana, IL: Univ. of Illinois.
Green, D. W., and J. W. Evans. 1987a. Mechanical properties of visually graded lumber: Volume 1, a summary. Madison, WI: United States Dept. of Agriculture, Forest Service, Forest Products Laboratory.
Green, D. W., and J. W. Evans. 1987b. Mechanical properties of visually graded lumber: Volume 4. Southern pine. Madison, WI: United States Dept. of Agriculture, Forest Service, Forest Products Laboratory.
Gupta, R., K. G. Gebremedhin, and J. R. Cooke. 1992. “Analysis of metal-plate-connected wood trusses with semi-rigid joints.” Trans. ASAE 35 (3): 1011–1018. https://doi.org/10.13031/2013.28695.
Gupta, R., and P. Limkatanyoo. 2008. “Practical approach to designing wood roof truss assemblies.” Pract. Period. Struct. Des. Constr. 13 (3): 135–146. https://doi.org/10.1061/(ASCE)1084-0680(2008)13:3(135).
He, J., F. Pan, and C. S. Cai. 2017. “A review of wood-frame low-rise building performance study under hurricane winds.” Eng. Struct. 141: 512–529. https://doi.org/10.1016/j.engstruct.2017.03.036.
He, J., F. Pan, and C. S. Cai. 2018a. “Assessment of ASCE 7-10 for wind effects on low-rise wood frame buildings with database-assisted design methodology.” Wind Struct. 27 (3): 163–173.
He, J., F. Pan, C. S. Cai, F. Habte, and A. Chowdhury. 2018b. “Finite-element modeling framework for predicting realistic responses of light-frame low-rise buildings under wind loads.” Eng. Struct. 164: 53–69. https://doi.org/10.1016/j.engstruct.2018.01.034.
Hoover, C. C., Jr., and J. R. McDonald. 1997. “Wind loading for roof trusses using ASCE standard.” Pract. Period. Struct. Des. Constr. 2 (2): 73–82. https://doi.org/10.1061/(ASCE)1084-0680(1997)2:2(73).
Hoq, S. M. A., and J. P. Judd. 2018. Comparison of wind design procedures for wood roof trusses. Structural Engineering and Materials Research Rep. No. 17/02. Laramie, WY: Dept. of Civil and Architectural Engineering, Univ. of Wyoming.
Kopp, G. A., and M. J. Morrison. 2018. “Component and cladding wind loads for low-slope roofs on low-rise buildings.” J. Struct. Eng. 144 (4): 04018019.
Li, Z., R. Gupta, and T. H. Miller. 1998. “Practical approach to modeling of wood truss roof assemblies.” Pract. Period. Struct. Des. Constr. 3 (3): 119–124. https://doi.org/10.1061/(ASCE)1084-0680(1998)3:3(119).
Limkatanyoo, P. 2003. “System behavior of three-dimensional wood truss assemblies.” M.S. thesis, Dept. of Wood Science and Engineering, Oregon State Univ.
Liu, W.-F., and W. M. Bulleit. 1995. “Overload behavior of sheathed lumber systems.” J. Struct. Eng. 121 (7): 1110–1118. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:7(1110).
Liu, X., and F. Lam. 2017. “Reliability analysis of lateral bracing forces in metal-plated wood trusses.” J. Struct. Eng. 143 (12): 04017171. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001908.
Martin, K. G., R. Gupta, D. O. Prevatt, P. L. Datin, and J. W. van de Lindt. 2011. “Modeling system effects and structural load paths in a wood-framed structure.” J. Archit. Eng. 17 (4): 134–143. https://doi.org/10.1061/(ASCE)AE.1943-5568.0000045.
Mehta, K. C., and R. D. Marshall. 1998. Guide to the use of the wind load provisions of ASCE 7-95. Reston, VA: ASCE.
Mohamadzadeh, M. 2014. “Analysis of metal plate connected wood truss assemblies under out-of-plane loads.” M.S. thesis, Dept. of Sustainable Biomaterials, Virginia Polytechnic Institute and State University.
Mohamadzadeh, M., D. P. Hindman, and A. G. Whaley. 2019. “Rotational stiffness of wood truss joints in lateral and diagonal bracing and truss–wall connections.” J. Archit. Eng. 25 (1): 04019003. https://doi.org/10.1061/(ASCE)AE.1943-5568.0000349.
Morris, J. C., D. P. Hindman, M. Mohamadzadeh, and T. Smith-Jackson. 2017. “Effect of bracing and anchor choice on the strength of metal plate–connected wood-truss assemblies carrying fall-arrest loads.” J. Archit. Eng. 23 (3): B4017001. https://doi.org/10.1061/(ASCE)AE.1943-5568.0000247.
Nowak, A. S., and K. R. Collins. 2012. Reliability of structures. Boca Raton, FL: CRC Press.
Pfretzschner, K. S., R. Gupta, and T. H. Miller. 2014. “Practical modeling for wind load paths in a realistic light-frame wood house.” J. Perform. Constr. Facil. 28 (3): 430–439. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000448.
Pierre, L. M. St., G. A. Kopp, D. Surry, and T. C. E. Ho. 2005. “The UWO contribution to the NIST aerodynamic database for wind loads on low buildings: Part 2. Comparison of data with wind load provisions.” J. Wind Eng. Ind. Aerodyn. 93 (1): 31–59. https://doi.org/10.1016/j.jweia.2004.07.007.
Rosowsky, D. V., and N. Cheng. 1999. “Reliability of light-frame roofs in high-wind regions. II: Reliability analysis.” J. Struct. Eng. 125 (7): 734–739. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:7(734).
SBCA (Structural Building Components Association). 2016. Guide to good practice for specifying and applying loads to structural building components. SBCA Load Guide v2.02. Madison, WI: SBCA Engineering and Technology Committee in cooperation with the Truss Plate Institute Technical Advisory Committee.
Song, X., and F. Lam. 2012. “Stability analysis of metal-plate-connected wood truss assemblies.” J. Struct. Eng. 138 (9): 1110–1119. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000502.
TPI (Truss Plate Institute). 2014. National design standard for metal plate connected wood truss construction. ANSI/TPI 1-2014. Alexandria, VA: TPI.
UFP Mid Atlantic, LLC. 2017. Truss design package for Job No. 17031755, dated March 27. Burlington, NC: UFP Mid Atlantic.
Wainright, L., R. Dexter, J. Vogt, and K. Grundahl. 2012. “Structural building components.” SBC Magazine, May 2012. https://www.sbcmag.info/issue/2012-may.
Wood, L. W. 1960. Variation of strength properties in woods used for structural purposes. Rep. No. R1780. Madison, WI: Forest Service, Forest Products Laboratory.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jul 19, 2019
Accepted: Apr 2, 2020
Published online: Jun 16, 2020
Published in print: Sep 1, 2020
Discussion open until: Nov 16, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.