Introduction of a Panelized Brick Veneer Wall System and Its Building Science Evaluation
Publication: Journal of Architectural Engineering
Volume 17, Issue 1
Abstract
This paper introduces a panelized brick veneer over steel stud backup wall system to address some of the shortcomings of conventional systems. Thermal and hygrothermal analyses of the proposed wall system with different stud gauges and arrangements are discussed. The movement joint design aspects, a pressure moderation performance evaluation, the simulated wind-driven water penetration results, and an example cost analysis are also presented. This study provides information about some of the attributes of the proposed system such as crack resistance and water penetration potential as well as the pressure moderation aspect. Some of the issues that need consideration for the practical application of the system are also described.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The study presented was partially supported by the General Services Administration. The support of the General Services Administration is gratefully acknowledged. The views expressed in this paper are those of the writers and do not necessarily represent those of the General Services Administration.
References
ASTM. (2000). “Standard test method for structural performance of exterior windows, curtain walls, and doors by cyclic static air pressure differential.” E 1233-00, West Conshohocken, PA.
ASTM. (2002). “Standard test method for structural performance of exterior windows, doors, skylights, and curtain walls by uniform static air pressure difference.” E 330-02, West Conshohocken, PA.
ASTM. (2005). “Standard test method for water penetration and leakage through masonry.” E 514-03c, West Conshohocken, PA.
American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE). (2004). “Energy standard for buildings except low-rise residential buildings.” 90.1-2004, Atlanta.
ASHRAE. (2005). ASHREA handbook fundamentals, Atlanta.
Anderson, J. P. (1996). “Precast framed curtainwall: A different way to clad.” Constr. Specifier, 49(2), 42–46.
Bombino, R. (1999). “Hygrothermal design issues with steel-framed enclosure wall systems.”M.S. thesis, Pennsylvania State University, University Park, PA.
Brick Industry Association (BIA). (1999). Brick veneer/steel stud walls, technical notes on brick construction, Reston, VA.
Brock, L. (1996). “Designed for durability: Case study of anchored brick veneer that meets technical and aesthetic requirements.” Proc., 7th North American Masonry Conf., The Masonry Society, Boulder, CO, 117–128.
Chen, H., and Trestain, T. (2004). “Steel stud brick veneer wall design.” Struct. Mag., December, 37–39.
Choi, Y.-H., and LaFave, J. M. (2004). “Performance of corrugated metal ties for brick veneer wall systems.” J. Mater. Civ. Eng., 16(3), 202–211.
Cowie, J. W. (1990). “Failure of steel studs.” Mag. Masonry Constr., 3(2), 82–84.
Devalapura, R. K., Krause, G. L., and Tadros, M. K. (1996). “Development and testing of prestressed clay brick walls.” Masonry Soc. J., 14(2), 99–112.
Drysdale, R. G., and Hamid, A. A. (2008). Masonry structures: Behavior and design, 3rd Ed., The Masonry Society, Boulder, CO.
Drysdale, R. G., and Suter, G. T. (1991). Exterior wall construction in high-rise buildings–brick veneer on concrete masonry or steel stud wall systems, Canada Mortgage and Housing Corporation (CMHC), Ottawa, Canada.
Earthquake Engineering Research Institute (EERI). (1990). “Loma Prieta earthquake reconnaissance report.” Earthquake Spectra, Supplement to Volume 6, Oakland, CA.
EERI. (1995). “Northridge Earthquake Reconnaissance Report, Vol. 1.” Earthquake Spectra, Supplement to Volume 11, Oakland, CA.
EERI. (2001). “The Nisqually, Washington, earthquake February 28, 2001.” Preliminary Reconnaissance Report 2001-01, Oakland, CA.
FERO Corporation. (2009). “Stud Shear Connector.” 〈http://www.ferocorp.com/pages/stud_shear/stud_shear.htm〉 (Dec. 28, 2009).
Gonchar, J. (2001). “Investigators search for cause of deadly scaffold collapse.” Eng. News-Rec., November 5, 15.
Grimm, C. T. (1992). “What is wrong with brick masonry veneer over steel studs?” Masonry Soc. J., 10(2), 9–14.
Grimm, C. T. (1993). “Masonry veneer anchors and cavity wall ties.”Masonry Soc. J., 12(1), 6–16.
Hagel, M. D., Lissel, S. L., and Sturgeon, G. R. (2007). “Comparison of theoretical and empirically determined service lives for wall ties in brick veneer steel stud wall systems.” Can. J. Civ. Eng., 34(11), 1424–1432.
Hamid, A. A., Becica, I. J., and Harris, H. G. (1985). “Performance of brick masonry veneers.” Proc., 7th Int. Brick Masonry Conf., University of Melbourne, Melbourne, Australia, 321–331.
Hatzinikolas, M. A., Longworth, J., and Warwaruk, J. (1985). “Brick veneer tie support.” Proc., 3rd North American Masonry Conf., The Masonry Society, Boulder, CO, 1–13.
Jalil, I., Kelm, W., and Klingner, R. E. (1993). “Performance of masonry and masonry veneer buildings in the 1989 Loma Prieta earthquake.” Proc., 6th North American Masonry Conf., The Masonry Society, Boulder, CO, 681–692.
Kelly, T., Goodson, M., Mayes, R., and Asher, J. (1990). “Analysis of the behavior of anchored brick veneer on metal stud systems subjected to wind and earthquake forces.” Proc., 5th North American Masonry Conf., The Masonry Society, Boulder, CO, 1359–1370.
KPFF Consulting Engineers. (1998). “Design guide for structural brick veneer.” Technical. Rep. Prepared for Western States Clay Products Association, Los Angeles.
Kroger, S. A. (2005). “Architecture built to last: Timelessness of brick.” M.S. thesis, Univ. of Cincinnati, Cincinnati.
LaBelle, J. C. (2004). “Façade repair examples in the Midwest: Cracking, twisting and falling.” Building façade maintenance, repair and inspection, ASTM STP 1444, ASTM, West Conshohocken, PA.
Laursen, P. T., and Ingham, J. M. (2000). “In-plane response of post-tensioned concrete masonry.” Proc., 12th Int. Brick/Block Masonry Conf., Spanish Ministry of Public Works, Madrid, Spain, 905–919.
Liang, J. (2006). “Development of a multihazard resistant panelized brick veneer wall system.”Ph.D. thesis, Pennsylvania State University, University Park, PA.
Lindow, E. S., and Jasinski, L. F. (2003). “Panelized wall construction: Design, testing, and construction procedures.” Performance of exterior building walls, STP 1422, P. G. Johnson, ed., ASTM, West Conshohocken, PA, 231–241.
Louis, M. J. (1999). “Prefabricated brick wall panels: Economy or nightmare?” Water problems in building exterior walls: Evaluation, prevention, and repair, STP 1352, J. Boyd and M. M. J. Sheffler, eds., ASTM, West Conshohocken, PA, 215–226.
The Masonry Standards Joint Committee (MSJC). (2002). “Building code requirements for masonry structures.” ACI 530-02/ASCE 5-02/TMS 402-02, Boulder, CO.
McCann, R. A. (1995). “Architectural precast concrete cladding connections in high seismic areas.” Prestressed Concrete Manufacturers Association of California (PCMAC) technical update, Glendale, CA.
McGinley, W. M. (2000). “An alternative design for brick veneer steel stud walls.” Masonry Soc. J., 18(2), 9–22.
McGinley, W. M., and Ernest, C. L. (2004). “Façade inspections, a must for both new and old buildings—A case study on two high rise buildings.” J. ASTM Int., 1(3).
Memari, A. M., Aliaari, M., and Hamid, A. A. (2002a). “Evaluation of seismic performance of anchored brick veneer walls.” Performance of exterior building walls, STP 1422, P. G. Johnson, ed., ASTM, West Conshohocken, PA, 115–131.
Memari, A. M., Burnett, E. F. P., and Kozy, B. M. (2002b). “Seismic performance of masonry ties used in brick veneer walls.” Constr. Build. Mater., 16(7), 397–407.
Palmer, W. D. (1999). “The power of prefabricated brick panels: Their advantages over laid-in-place brick.” Masonry Constr., 12(3), 22–34.
Peterson, J. E., and Shelton, T. (2009). “Evaluation and repair of a distressed masonry veneer façade: A case study of the Litton Reaves repair project.” Proc., 5th Congress on Forensic Engineering, ASCE, Reston, VA.
RS Means. (2005). Building construction cost data, PB 2005, Kingston, MA.
Schindler, G. (2004). “Design of brick veneer over steel studs.” Struct. Mag., December, 21–24.
Schulatz, A. E., Porter, M., Bigelow, O., and Stehly, R. (1999). “Masonry building performance during the March 29, 1998 southern Minnesota tornadoes.” Proc., 8th North American Masonry Conf., The Masonry Society, Boulder, CO, 797–808.
Straube, J., and Burnett, E. (2005). Building science for building enclosures, Building Science Press, Westford, MA.
Suter, G. T., Drysdale, R. G., and Keller, H. (1990). “Canadian research on the brick veneer/steel stud wall system.” Proc., 5th North American Masonry Conf., The Masonry Society, Boulder, CO, 1287–1301.
Tawresey, J. G. (2004). “Structural brick masonry walls.” Struct. Mag., December, 33–36.
Information & Authors
Information
Published In
Journal of Architectural Engineering
Volume 17 • Issue 1 • March 2011
Pages: 1 - 14
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Oct 19, 2008
Accepted: Jun 17, 2010
Published online: Feb 15, 2011
Published in print: Mar 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.