Measurement of the Timoshenko Shear Stiffness. I: Effect of Warping
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Composites for Construction
Volume 11, Issue 3
Abstract
Fiber-reinforced polymer (FRP) composite beams are increasingly finding use in construction. Due to their lower stiffness relative to steel sections, the design of FRP structures is usually deflection controlled. Furthermore, shear deformation can be significant in FRP beams, thus, requiring the use of the Timoshenko beam theory to estimate deflections. However, the Timoshenko shear stiffness can be difficult to measure. Part of the measurement error has been attributed to shear warping effects. It has been hypothesized that warping restraints at loading points and supports increase the apparent shear stiffness to a degree that is significant at relatively short spans, e.g., to 15. In this study, the influence of warping on short to moderate length FRP beams under various types of loading and boundary conditions is considered using finite-element analysis. In particular, a commercially available thin-walled FRP beam was investigated. The results suggest that warping has a negligible effect for thin-walled beams at reasonable spans, i.e., . On the contrary, the effective shear stiffness is found to decrease at shorter span lengths. This is the first of two papers in a series.
Get full access to this article
View all available purchase options and get full access to this article.
References
Allen, H. G. (1969). Analysis and design of structural sandwich panels, Pergamon, Oxford.
Bank, L. C. (1987). “Shear coefficients for thin-walled composite beams.” Compos. Struct., 8(1), 47–61.
Bank, L. C. (1989). “Flexural and shear moduli of full-section fiber reinforced plastic (FRP) pultruded beams.” J. Test. Eval., 17(1), 40–45.
Bank, L. C., and Melehan, T. P. (1989). “Shear coefficients for multicelled thin-walled composite beams.” Compos. Struct., 11(4), 259–276.
Barbero, E. J. (1999). Introduction to composite materials design, Taylor and Francis, New York.
Barbero, E. J., Fu, S.-H., and Raftoyiannis, I. (1991). “Ultimate bending strength of composite beams.” J. Mater. Civ. Eng., 3(4), 292–306.
Barbero, E. J., Lopez-Anido, R., and Davalos, J. F. (1993). “On the mechanics of thin-walled laminated composite beams.” J. Compos. Mater., 27(8), 806–829.
Bauchau, O. A. (1985). “A beam theory for anisotropic materials.” J. Appl. Mech., 52, 416–421.
Cosenza, E., Lazzaro, F., and Peece, M. (1996). “Experimental evaluation of bending and torsional deformability of FRP pultruded beams.” Advanced composite materials in bridges and structures, M. M. El-Badry, ed., Canadian Society for Civil Engineering, Montreal.
Cowper, G. R. (1996). “The shear coefficient in Timoshenko’s beam theory.” J. Appl. Mech., 33, 335–340.
Davalos, J. F., Salim, H. A., Qiao, P., and Lopez-Anido, R. (1996). “Analysis and design of pultruded FRP shapes under bending.” Composites, Part B, 27(3–4), 295–305.
Dharmarajan, S., and McCutchen, H. (1973). “Shear coefficients for orthotropic beams.” J. Compos. Mater., 7, 530–535.
Dufort, L., Drapier, S., and Grediac, M. (2001a). “Closed-form solution for the cross-section warping in short beams under three-point bending.” Compos. Struct., 52(2), 233–246.
Dufort, L., Grediac, M., and Surrel, Y. (2001b). “Experimental evidence of the cross-section warping in short composite beams under three point bending.” Compos. Struct., 51(1), 37–47.
Fischer, S., Roman, I., Harel, H., Marom, G., and Wagner, H. D. (1981). “Simultaneous determination of shear and Young’s moduli in composites.” J. Test. Eval., 9(5), 303–307.
Hashin, J., and Rosen, B. W. (1964). “The elastic moduli of fiber-reinforced materials.” J. Appl. Mech., 223–230.
Hayes, M. D. (2003). “Structural analysis of a pultruded composite beam: Shear stiffness determination and strength and fatigue life predictions.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Hayes, M. D., and Lesko, J. J. (2007). “Measurement of the Timoshenko shear stiffness. Part II: Effect of transverse compressibility.” J. Compos. Constr., 11(3), 343–349.
Hjelmstad, K. D. (1987). “Warping effects in transverse bending of thin-walled beams.” J. Eng. Mech., 113(6), 907–924.
Hyer, M. W. (1998). Stress analysis of fiber-reinforced composite materials, McGraw-Hill, Boston.
Jones, R. M. (1975). Mechanics of composite materials, Hemisphere Publishing Corporation, New York.
Lopez-Anido, R., and GangaRao, H. V. S. (1996). “Warping solution for shear lag in thin-walled orthotropic composite beams.” J. Eng. Mech., 122(5), 449–457.
Madabhusi-Raman, P., and Davalos, J. F. (1996). “Static shear correction factor for laminated rectangular beams.” Composites, Part B, 27(3–4), 285–293.
Restrepo, E. S. (2002). “Determination of AASHTO bridge design parameters through field evaluation of the Route 601 Bridge: A bridge utilizing Strongwell’s fiber-reinforced polymer double web beams as the main load carrying members.” Master’s thesis, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Schniepp, T. J. (2002). “Design manual development for a hybrid, FRP double-web beam and characterization of shear stiffness in FRP composite beams.” Master’s thesis, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Sims, G. D., Johnson, A. F., and Hill, R. D. (1987). “Mechanical and structural properties of a GRP pultruded section.” Compos. Struct., 8, 173–187.
Teh, K. K., and Huang, C. C. (1979). “Shear deformation coefficient for generally orthotropic beam.” Fibre Sci. Technol., 12, 73–80.
Timoshenko, S. P. (1921). “On the correction for shear of the differential equation for transverse vibrations of prismatic bars.” Philos. Mag., 41, 744–746.
Timoshenko, S. P. (1922). “On the transverse vibrations of bars of uniform cross section.” Philos. Mag., 43, 125–131.
Tsai, S. W., and Hahn, H. T. (1980). Introduction to composite materials, Technomic, Lancaster, Pennsylvania.
Waldron, C. (2001). “Determination of the design parameters for the Route 601 Bridge: A bridge containing the Strongwell hybrid composite double web beam.” Master’s thesis, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jul 11, 2005
Accepted: May 16, 2006
Published online: Jun 1, 2007
Published in print: Jun 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.