Design of a Test Specimen to Assess the Effective Bond Length of Carbon Fiber-Reinforced Polymer Strips Bonded to Fatigued Steel Bridge Girders
Publication: Journal of Composites for Construction
Volume 9, Issue 4
Abstract
Single-lap and double-lap specimens have been widely used to determine the shear strength of epoxy adhesives for many applications, including mechanical joints and retrofit of wing skins. Although it has been known that the stress state in the adhesive is not uniform in shear, but rather a combined stress state of peeling stress and shear stress, these specimens are useful to determine the bond strength if the application of the adhesive is similar in shape and material properties to the test setup. However, when the application does not have a shape similar to the single-lap or double-lap specimens, the test results of the lap specimens may not be applicable to the practical application. This is often the case for the use of epoxy adhesives in structural engineering applications. In this paper, one example of an application in which a single-lap or double-lap specimen is not appropriate for determination of the bond strength of the epoxy adhesive will be presented. The application of the epoxy adhesive discussed herein involves rehabilitation with bonded carbon fiber-reinforced polymer (CFRP) strips of the tension flanges of fatigued steel I-griders used in bridges. This application provides a cost-effective means of repairing these bridge girders, so long as the effective bond strength of the CFRP and adhesive are sufficient. In this work, the stress distribution in the adhesive layer is analyzed and compared between a prototype repaired bridge girder and various specimen models to determine an appropriate specimen and test setup for assessing the effective bond length of the adhesive. This study points out the strengths and weaknesses of standard single-lap and double-lap specimens and proposes that the new test setup is a suitable alternative for a wide range of applications in which the adherend is subjected to tension plus flexure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for this research was provided by the Minnesota Department of Transportation, the Center for Transportation Studies, and the University of Minnesota. Supercomputing resources were provided by the Minnesota Supercomputer Institute. The writers gratefully acknowledge the advice and contributions to this research from Paul M. Bergson, Eray Baran, and Yuying Hu of the University of Minnesota.
References
ABAQUS/standard manual, version 5.4. (1994). Hibbitt, Karlsson, and Sorensen, Inc., Pawtucket, R.I.
Adams, R. D., and Wake, W. C. (1984). Structural adhesive joints in engineering, Elsevier, New York.
ASTM. (1995). “Standard guide for use of adhesive-bonded single lap-joint specimen test results.” ASTM D 4896-95, West Conshohocken, Pa.
Baker, A. A., and Chester, R. J. (1993). “Recent advances in bonded composite repair technology for metallic aircraft components.” Proc., Advanced Composite ’93: Int. Conf. on Advanced Composite Materials, Minerals, Metals, and Materials Society, Warrendale, Pa., 45–49.
Baker, A. A., and Jones, R. (1987). Bonded repair of aircraft structures, Martinus Nijhoff, Dordrecht, The Netherlands.
Baker, A. A., Rose, L. R. F., and Walker, K. F. (1999). “Repair substantiation for a bonded composite repair to F111 lower wing skin.” Appl. Compos. Mater., 6, 251–267.
Dorn, L., and Liu, W. (1992). “The stress state and failure properties of adhesive-bonded plastic/metal joint.” Int. J. Adhes. Adhes., 13(1), 21–31.
Fredell, R., Guijt, C., and Mazza, J. (1999). “An integrated bonded repair system: A reliable means of giving new life to aging airframes.” Appl. Compos. Mater., 6, 269–277.
Harris, J. A., and Adams, R. D. (1984). “Strength prediction of bonded single lap joints by non-linear finite element method.” Int. J. Adhes. Adhes., 4(2), 65–78.
Ikegami, K., et al. (1996). “Benchmark tests on adhesive strength in butt, single, and double lap joints and double-cantilever beams.” Int. J. Adhes. Adhes., 16(4), 219–226.
Nozaka, K., Shield, C. K., and Hajjar, J. F. (2001). “Repair of fatigued steel bridge girders with carbon fiber strips.” Proc., 5th National Science Foundation Workshop on Bridge Research in Progress, National Science Foundation, Arlington, Va., 271–276.
Nozaka, K., Shield, C. K., and Hajjar, J. F. (2003). “Repair and retrofit of steel bridge girders with carbon fiber strips: Final report.” Rep. No. Mn/DOT 2004-02, Minnesota Department of Transportation, St. Paul, Minn.
Nozaka, K., Shield, C. K., and Hajjar, J. F. (2004). “Effective bond length of carbon-fiber-reinforced polymer strips bonded to fatigued steel bridge I-girders.” J. Bridge Eng., 10(2), 195–205.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Jan 2, 2003
Accepted: Feb 7, 2005
Published online: Aug 1, 2005
Published in print: Aug 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.