Numerical Model for Reinforced Soil Segmental Walls under Surcharge Loading
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 132, Issue 6
Abstract
The construction and surcharge loading response of four full-scale reinforced-soil segmental retaining walls is simulated using the program FLAC. The numerical model implementation is described and constitutive models for the component materials (i.e., modular block facing units, backfill, and four different reinforcement materials) are presented. The influence of backfill compaction and reinforcement type on end-of-construction and surcharge loading response is investigated. Predicted response features of each test wall are compared against measured boundary loads, wall displacements, and reinforcement strain values. Physical test measurements are unique in the literature because they include a careful estimate of the reliability of measured data. Predictions capture important qualitative features of each of the four walls and in many instances the quantitative predictions are within measurement accuracy. Where predictions are poor, explanations are provided. The comprehensive and high quality physical data reported in this paper and the lessons learned by the writers are of value to researchers engaged in the development of numerical models to extend the limited available database of physical data for reinforced soil wall response.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support for this study was provided by the Natural Sciences and Engineering Research Council (NSERC) of Canada and the following U.S. State Departments of Transportation: Alaska, Arizona, California, Colorado, Idaho, Minnesota, New York, North Dakota, Oregon, Utah, Washington, and Wyoming. The writers are also grateful for the financial support from the Academic Research Program at RMC and operating grants from the Department of National Defence, Canada. The writers also acknowledge the many helpful comments by D. Walters and T. M. Allen during the preparation of this paper and the contribution of P. Burgess and N. Vlachopoulos (former graduate students) who carried out the physical model tests described in the paperNRC.
References
AASHTO. (2002). Standard specifications for highway bridges, 17th Ed., Washington, D.C.
Allen, T. M., and Bathurst, R. J. (2002). “Soil reinforcement loads in geosynthetic walls at working stress conditions.” Geosynthet. Int., 9(5–6), 525–566.
Allen, T. M., Bathurst, R. J., and Berg, R. R. (2002). “Global level of safety and performance of geosynthetic walls: A historical perspective.” Geosynthet. Int., 9(5–6), 395–450.
Allen, T. M., Bathurst, R. J., Holtz, R. D.,Walters, D. L., and Lee, W. F. (2003). “A new working stress method for prediction of reinforcement loads in geosynthetic walls.” Can. Geotech. J., 40(5), 976–994.
ASTM. (1996). “Standard test method for tensile properties of geotextiles by the wide-width strip method.” ASTM D4595, Annual book of ASTM standards, West Conshohocken, Pa., 4.09, 698–708.
Bathurst, R. J. (1993). “Investigation of footing restraint on stability of large-scale reinforced soil wall tests.” Proc., 46th Canadian Geotechnical Conf., Saskatoon, Sask., Canada, 389–398.
Bathurst, R. J., Allen, T. M., and Walters, D. L. (2002). “Short-term strain and deformation behavior of geosynthetic walls at working stress conditions.” Geosynthet. Int., 9(5–6), 451–482.
Bathurst, R. J., Allen, T. M., and Walters, D. L. (2005). “Reinforcement loads in geosynthetic walls and the case for a new working stress design method (Mercer Lecture).” Geotext. Geomembr., 23(4), 287–322.
Bathurst, R. J., Walters, D. L., Hatami, K., and Allen, T. M. (2001). “Full-scale performance testing and numerical modelling of reinforced soil retaining walls.” Proc., Int. Symp. on Earth Reinforcement, IS Kyushu (2001), Fukuoka, Japan, Special plenary lecture, Vol. 2, 777–799.
Bathurst, R. J., Walters, D., Vlachopoulos, N., Burgess, P., and Allen, T. M. (2000). “Full scale testing of geosynthetic reinforced walls.” ASCE Special Publication No. 103, Advances in Transportation and Geoenvironmental Systems using Geosynthetics, Proc., Geo-Denver 2000, Invited keynote paper, 201–217.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Geotechnique, 36(1), 65–78.
Bowles, J. E. (1996). Foundation analysis and design, 5th Ed., McGraw-Hill, New York.
Cazzuffi, D., Picarelli, L., Ricciuti, A., and Rimoldi, P. (1993). “Laboratory investigations on the shear strength of geogrid reinforced soils.” ASTM Special Technical Publication No. 1190, Geosynthetic Soil Reinforcement Testing Procedures, S.C.J. Cheng, ed., West Conshohocken, Pa., 119–137.
Christopher, B. R., Gill, S. A., Giroud, J.-P., Juran, I., Mitchell, J. K., Schlosser, F., and Dunnicliff, J. (1990). “Reinforced soil structures Vol. 1, Design and construction guidelines.” FHWA Rep. No. FHWA-RD-89-043, Federal Highway Administration, Washington, D.C.
Duncan, J. M., Byrne, P., Wong, K. S., and Mabry, P. (1980). “Strength, stress-strain and bulk modulus parameters for finite-element analysis of stresses and movements in soil masses.” Rep. No. UCB/GT/80-01, Dept. of Civil Engineering, Univ. of California, Berkeley, Calif.
Duncan, J. M., Williams, G. W., Sehn, A. L., and Seed, R. B. (1991). “Estimation of earth pressures due to compaction.” J. Geotech. Eng., 117(12), 1833–1847.
Elias, V., Christopher, B. R., and Berg, R. R. (2001). “Mechanically stabilized earth walls and reinforced soil slopes—design and construction guidelines.” FHWA-NHI-00-043, Federal Highway Administration, Washington, D.C.
Gotteland, Ph., Gourc, J. P., and Villard, P. (1997). “Geosynthetic reinforced structures as bridge abutments: full scale experimentation and comparison with modelisations.” Proc., Int. Symp. on Mechanically Stabilized Backfill, J. T. H. Wu, ed., Denver, 25–34.
Hanna, A. (2001). “Determination of plane-strain shear strength of sand from the results of triaxial tests.” Can. Geotech. J., 38(6), 1231–1240.
Hatami, K., and Bathurst, R. J. (2005). “Development and verification of a numerical model for the analysis of geosynthetic reinforced-soil segmental walls.” Can. Geotech. J., 42(4), 1066–1085.
Itasca Consulting Group. (2001). FLAC—fast Lagrangian analysis of continua, Version 4.00, Minneapolis.
Janbu, N. (1963). “Soil compressibility as determined by odometer and triaxial tests.” Proc., European Conf. on Soil Mechanics and Foundation Engineering, Wissbaden, Germany, Vol. 1, 19–25.
Karpurapu, R. G., and Bathurst, R. J. (1995). “Behaviour of geosynthetic reinforced soil retaining walls using the finite element method.” Comput. Geotech., 17(3), 279–299.
Lade, P. V., and Lee, K. L. (1976). “Engineering properties of soils.” Rep. No. UCLA-ENG-7652, Dept. of Civil Engineering, Univ. of California.
Lee, W. F. (2000). “Internal stability analyses of geosynthetic reinforced retaining walls.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Univ. of Washington, Seattle.
Ling, H. I., and Leshchinsky, D. (2003). “Finite element parametric study of the behavior of segmental block reinforced-soil retaining walls.” Geosynthet. Int., 10(3), 77–94.
Marachi, N. D., Duncan, J. M., Chan, C. K., and Seed, H. B. (1981). “Plane strain testing of sand.” Laboratory Shear Strength of Soil, ASTM Special Technical Bulletin 740, R. N. Yong and F. C. Townsend, eds., American Society for Testing and Materials, West Conshohocken, Pa., 294–302.
Rowe, R. K., and Ho, S. K. (1997). “Continuous panel reinforced soil walls on rigid foundations.” J. Geotech. Geoenviron. Eng., 123(10), 912–920.
Rowe, R. K., and Skinner, G. D. (2001). “Numerical analysis of geosynthetic reinforced retaining wall constructed on a layered soil foundation.” Geotext. Geomembr., 19(7), 387–412.
Walters, D. L., Allen, T. M., and Bathurst, R. J. (2002). “Conversion of geosynthetic strain to load using reinforcement stiffness.” Geosynthet. Int.9(5–6), 483–523.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Nov 16, 2004
Accepted: Nov 16, 2005
Published online: Jun 1, 2006
Published in print: Jun 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.