Rotational Restraint of Pile Caps during Lateral Loading
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 129, Issue 9
Abstract
A pure fixed-head (zero-rotation) condition at the top of a group of laterally loaded piles is seldom achievable in the field, even when piles are installed in a group that is “rigidly” constrained by a stiff concrete pile cap. Assuming complete fixity during design (zero rotation at the pile head) can result in underestimated values of pile-head deflection, and incorrect estimates of the magnitude and the location of maximum bending moments. A simple and practical approach is presented for estimating the moment restraint that is provided by the pile cap at the top of a pile group. The moment restraint, represented by the rotational restraint coefficient serves as a boundary condition for analyzing groups of laterally loaded piles. Full-scale field tests performed on two pile groups with concrete pile caps show that the proposed method for estimating rotational restraint provides results that are in good agreement with measured field performance.
Get full access to this article
View all available purchase options and get full access to this article.
References
Altaee, A., Evgin, E., and Fellenius, B. H.(1992). “Axial load transfer for piles in sand. I: Tests on an instrumented precast pile.” Can. Geotech. J., 29(1), 11–20.
American Association of State and Highway Transportation Officials (AASHTO). (1994). “LRFD bridge design specifications.” American Association of State Highway and Transportation Officials, Washington, D.C.
Banerjee, P. K., and Davies, T. G. (1977). “Analysis of pile groups embedded in Gibson soil.” Proc., 9th Int. Conf. on Soil Mechanics and Found. Eng., Tokyo, Vol. 1, 381–386.
Brown, D. A., and Reese, L. C. (1985). “Behavior of a large-scale pile group subjected to cyclic lateral loading.” Report to the Minerals Management Services, U.S. Dept. of Interior, Reston, Va; Dept. of Research, Federal Highway Administration, Washington, D.C.; and U.S. Army Engineer Waterways Experiment Station, Vicksburg, Miss.
Brown, D. A., and Shie, C. F.(1991). “Modification of curves to account for group effects on laterally loaded piles.” Geotechn. Eng. Congress, 1(GSP 27), 479–490.
Burland, J.(1973). “Shaft friction of piles in clay—A simple fundamental approach.” Ground Eng., 6(3), 30–42.
Concrete Reinforcing Steel Institute (CRSI). (1992). CRSI handbook, Schaumburg, Ill.
Cox, W. R., Dixon, D. A., and Murphy, B. S. (1984). “Lateral-load tests on 25.4-mm-diameter piles in very soft clay in side-by-side and in-line groups.” Laterally loaded deep foundations: Analysis and performance, ASTM, STP 835, 122–139.
Davisson, M. T. (1975). “Pile load capacity.” Design construction and performance of deep foundations, ASCE, Univ. of Calif., Berkeley, Calif., 1–49.
Ensoft. (1997). “LPILE Plus 3.0: A program for analysis of piles and drilled shafts under lateral loads.” Ensoft, Inc., Austin, Tex.
Ensoft. (2000). “GROUP 5.0: A program for the analysis of a group of piles subjected to axial and lateral loading.” Ensoft, Inc., Austin, Tex.
Esrig, M. E., and Kirby, R. C. (1979). “Advances in general effective stress method for the prediction of axial capacity for driven piles in clay.” Proc., 11th Annual Offshore Technology Conf., Houston, Texas, 437–449.
Gardner, W. S. (1975). “Considerations in the design of drilled piers.” Design construction and performance of deep foundations, San Francisco, 1–32.
Guo, W. D.(2000). “Vertically loaded single piles in Gibson soil.” J. Geotech. Geoenviron. Eng., 126(2), 189–193.
Guo, W. D., and Randolph, M. F.(1997). “Vertically loaded piles in nonhomogeneous media.” Int. J. Numer. Analyt. Meth. Geomech., 21(8), 507–532.
Hansen, B. (1961). “The ultimate resistance of rigid piles against transversal forces.” Bull. No. 12, Danish Geotechnical Institute, Copenhagen, Denmark.
Hoit, M., Hays, C., and McVay, M. (1997). “Florida pier. Methods and models for pier analysis and design.” Transp. Research Board, 76th Meeting, TRB No. 97-0554.
Kim, J. B. (1984). “Pile caps subjected to lateral loads.” Analysis and Design of Pile Foundations, ASCE Symp. Proc. Geotechnical Engineering Division, ASCE, New York.
Kulhawy, F. H. (1984). “Limiting tip and side resistance.” Analysis and Design of Pile Foundations, ASCE National Convention, ASCE, New York, 80–98.
Lieng, J. T. (1989). “A model for group behavior of laterally loaded piles.” Proc., Offshore Technology Conf., Houston, 377–394.
Matlock, H., and Reese, L. C. (1961). “Foundation analysis of offshore pile supported structures.” Proc., 5th Int. Conf. on Soil Mechanics and Foundation Engineering, Paris, Vol. 2, 91–97.
McVay, M., Casper, R., and Shang, T.(1995). “Lateral response of three-row groups in loose to dense sands at 3D and 5D pile spacing.” J. Geotech. Geoenviron. Eng., 121(5), 436–441.
McVay, M., Zhang, L., Molnit, T., and Lai, P.(1998). “Centrifuge testing of large laterally loaded pile groups in sands.” J. Geotech. Geoenviron. Eng., 124(10), 1016–1026.
Meimon, Y., Baguelin, F., and Jezequel, J. F. (1986). “Pile group behavior under long time lateral monotonic and cyclic loading.” Proc., 3rd Int. Conf. on Numerical Methods on Offshore Piling, Institute Francais Du Petrole, Nantes, France, 285–302.
Meyerhof, G. G.(1976). “Bearing capacity and settlement of pile foundations.” J. Geotech. Eng. Div., Am. Soc. Civ. Eng., 102(3), 195–228.
Mokwa, R. L., and Duncan, J. M. (1999). “Investigation of the resistance of pile caps to lateral loading.” A Report of Research Performed Under Sponsorship of the VA Transportation Research Council, VTRC 99-CR.
Mokwa, R. L., and Duncan, J. M. (2000). “Development of curves for partly saturated silts and clays with both cohesion and friction.” ASCE Geotechnical Special Publication (GSP No. 100), New Technological and Design Developments in Deep Foundations, GEO-Denver 2000, 224–239.
Mokwa, R. L., and Duncan, J. M.(2001). “Experimental evaluation of lateral-load resistance of pile caps.” J. Geotech. Geoenviron. Eng., 127(2), 185–192.
Morrison, C., and Reese, L. C. (1986). “A lateral load test of full-scale pile group in sand.” Rep. No. GR86-1, Federal Highway Administration, Washington, D.C.
Nicola, A., and Randolph, M. F.(1999). “Centrifuge modeling of pipe piles in sand under axial loads.” Geotechnique, 49(3), 295–318.
Nottingham, L., and Schmertmann, J. (1975). “An investigation of pile capacity design procedures.” Final Rep. No. D629 to Federal Dept. of Transportation from the Dept. of Civil Engineering, Univ. of Florida, September.
Poulos, H. G.(1987). “Analysis of residual stress effects in piles.” J. Geotech. Eng., 113(3), 216–229.
Poulos, H. G., and Davis, E. H. (1980). Pile foundation analysis and design, Wiley, New York.
Poulos, H. G., and Randolph, M. F.(1983). “Pile group analysis: A study of two methods.” J. Geotech. Eng., 109(3), 355–372.
Rollins, K. P., Peterson, K. T., and Weaver, T. J.(1998). “Lateral load behavior of full-scale pile group in clay.” J. Geotech. Geoenviron. Eng., 124(6), 468–478.
Ruesta, P. F., and Townsend, F. C.(1997). “Evaluation of laterally loaded pile group at Roosevelt Bridge.” J. Geotech. Geoenviron. Eng., 123(12), 1153–1161.
Sowa, V. A.(1970). “Pulling capacity of concrete cast in situ bored piles.” Can. Geotech. J., 7, 482–493.
Tomlinson, M. J. (1987). Pile design and construction, Viewpoint Publication, 3rd Ed., Palladian Publications, London.
Vijayvergiya, V. N., and Focht, J. A. (1972). “A new way to predict the capacity of piles in clay.” Proc., 4th Annual Offshore Technology Conf., Houston, Texas, Vol. 2, 865–874.
Wang, S. T., and Reese, L. C. (1993). “COM624P-Laterally loaded pile analysis program for the microcomputer.” Federal Highway Administration Publ. No. FHWA-SA-91-048, August.
Information & Authors
Information
Published In
Copyright
Copyright © 2003 American Society of Civil Engineers.
History
Received: Aug 31, 2000
Accepted: Nov 22, 2002
Published online: Aug 15, 2003
Published in print: Sep 2003
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.