Scale Effect of Strip and Circular Footings Resting on Dense Sand
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 127, Issue 7
Abstract
This paper presents the results of a research program of strip and circular footings resting on dry dense sand. The scale effect on the bearing capacity and the shape factor s;gg of the footings is investigated numerically and experimentally. The footings are analyzed using the method of characteristics. A wedge failure mechanism has been adopted. Triaxial compression tests conducted under confining pressures up to 2,500 kPa show that the friction angle of dense sand decreases with stress level. The stress-dependent friction angle of soil is adopted in the characteristics analysis. The numerical results indicate that the bearing capacity increases exponentially with footing size. With increasing footing size, the bearing capacity factor N;gg is reduced, while the shape factor s;gg is increased. Centrifuge tests of strip and circular footings with dimensions up to the equivalent of 7 m have been conducted. The experimental work verified the numerical analysis through the consistency of results.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Aiban, S. A., and Znidarcic, D. (1995). “Centrifugal modeling of bearing capacity of shallow foundations on sands.”J. Geotech. Engrg., ASCE, 121(10), 704–712.
2.
Bolton, M. D., and Lau, C. K. ( 1993). “Vertical bearing capacity factors for circular and strip footings on Mohr-Coulomb soil.” Can. Geotech. J., Ottawa, 30, 1024–1033.
3.
Caquot, A., and Kerisel, J. ( 1953). “Sur le terme de surface dans le calcul des fondations en milieu pulverulent.” Proc., 3rd Int. Conf. on Soil Mech. and Found. Engrg., Vol. 1, International Society of Soil Mechanics and Foundation Engineering, London, 336–337.
4.
Chen, W. F. ( 1975). Limit analysis and soil plasticity, Elsevier Science, New York.
5.
Clark, J. I. ( 1998). “The settlement and bearing capacity of very large foundations on strong soils: The 1996 R. M. Hardy lecture.” Can. Geotech. J., Ottawa, 35, 131–145.
6.
De Beer, E. E. ( 1965). “Bearing capacity and settlement of shallow foundations on sand.” Proc., Bearing Capacity and Settlement of Found. Symp., Duke University, Durham, 15–34.
7.
De Beer, E. E. ( 1970). “Experimental determination of the shape factors and bearing capacity factors of sand.” Géotechnique, London, 20(4), 387–411.
8.
Graham, J., and Hovan, J. M. ( 1986). “Stress characteristics for bearing capacity in sand using a critical state model.” Can. Geotech. J., Ottawa, 23, 195–202.
9.
Graham, J., and Stuart, J. G. (1971). “Scale and boundary effects in foundation analysis.”J. Soil Mech. and Found. Div., ASCE, 97(11), 1533–1548.
10.
Hansen, J. B. ( 1970). “A revised and extended formula for bearing capacity.” Bull. 28, Danish Geotechnical Institute, Copenhagen, 5–11.
11.
Ho, M. K., and Lopes, R. (1969). “Contact pressure of a rigid circular foundation.”J. Soil Mech. and Found. Div., ASCE, 95(3), 791–802.
12.
Kusakabe, O., Yamaguchi, H., and Morikage, A. ( 1991). “Experiment and analysis on the scale effect of N;gg for circular and rectangular footings.” Proc., Int. Conf. Centrifuge '91, H. Y. Ko and F. G. McLean, eds., Balkema, Rotterdam, The Netherlands, 179–186.
13.
Larkin, L. A. (1968). “Theoretical bearing capacity of very shallow footings.”J. Soil Mech. and Found. Div., ASCE, 94(6), 1347–1357.
14.
Meyerhof, G. G. ( 1950). “The bearing capacity of sand.” PhD thesis, University of London, London.
15.
Meyerhof, G. G. ( 1963). “Some recent research on the bearing capacity of foundations.” Can. Geotech. J., Ottawa, 1, 16–26.
16.
Okamura, M., Takemura, J., and Kimura, T. ( 1997). “Experimental and analytical studies on bearing capacities of rectangular footings on sand.” 3rd Int. Geotech. Engrg. Conf.
17.
Schofield, A. N. ( 1980). “Cambridge geotechnical centrifuge operations.” Géotechnique, London, 30(3), 227–268.
18.
Sokolovskii, V. V. ( 1965). Statics of granular media, Pergamon, New York.
19.
Taylor, R. N. ( 1995). “Centrifuges in modeling: Principles and scale effects.” Chapter 2, Geotechnical centrifuge technology, R. N. Taylor, ed., Blackie Academic & Professional, London, 19–33.
20.
Terzaghi, K. ( 1943). Theoretical soil mechanics, Wiley, New York.
21.
Vesic, A. S. ( 1965). “Ultimate loads and settlements of deep foundation.” Proc., Bearing Capacity and Settlement of Found. Symp., Duke University, Durham, 63–68.
22.
Vesic, A. S. (1973). “Analysis of ultimate loads of shallow foundations.”J. Soil Mech. and Found. Div., ASCE, 99(1), 45–73.
23.
Zhu, F. ( 1998). “Centrifuge modeling and numerical analysis of bearing capacity of ring foundations on sand.” PhD thesis, Memorial University of Newfoundland, St. John's, Canada.
24.
Zhu, F., Clark, J. I., and Phillips, R. ( 1998). “Bearing capacity of ring foundations under vertical load.” Proc., Int. Conf. Centrifuge '98, T. Kimura, O. Kusakabe, and T. Takemura, eds., Balkema, Rotterdam, The Netherlands, 441–446.
Information & Authors
Information
Published In
History
Received: Dec 7, 1999
Published online: Jul 1, 2001
Published in print: Jul 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.