Interaction of Foundry Sands with Geosynthetics
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 127, Issue 4
Abstract
Excess foundry sands from gray-iron casting are a mixture of sand, bentonite, and additives that can have properties desirable for structural fills and hydraulic barriers, depending on their bentonite content. To facilitate beneficial reuse of foundry sands, typical strength parameters need to be available so that designers can make comparisons with designs employing virgin earthen materials. To provide typical design parameters, a testing program was conducted to characterize the strength of foundry sands and their interaction with geosynthetics. Small-scale direct shear tests, large-scale multistage interface shear tests, and pullout tests were conducted using foundry sands with bentonite contents representing the range normally found in the casting industry and three geosynthetics (geotextile, geogrid, and geomembrane). The results indicate that foundry sands can be used effectively in geotechnical construction. Friction angles of the as-compacted foundry sands generally ranged between 39° and 43°, and the as-compacted cohesions ranged between 17 and 28 kPa. Drained friction angles were similar to as-compacted friction angles except at high bentonite content. Typical interface friction angles ranged between 25° and 35°, with efficiencies ranging between 0.5 and 0.9. Interaction coefficients from the pullout tests ranged between 0.2 and 1.7.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Abichou, T., Benson, C., and Edil, T. (2000). “Foundry green sands as hydraulic barriers: Laboratory study.”J. Geotech. and Geoenvir. Engrg., ASCE, 126(12), 1174–1183.
2.
Abichou, T., Benson, C., and Edil, T. B. ( 1998a). “Database on beneficial reuse of foundry by-products.” Recycled materials in geotechnical applications, Geotech. Spec. Publ. No. 79, C. Vipulanandan and D. Elton, eds., ASCE, Reston, Va., 210–223.
3.
Abichou, T., Benson, C., Edil, T. B., and Freber, B. W. ( 1998b). “Using waste foundry sand for hydraulic barriers.” Recycled materials in geotechnical applications, Geotech. Spec. Publ. No. 79, C. Vipulanandan and D. Elton, eds., ASCE, Reston, Va., 86–99.
4.
Bemben, S. M., and Shulze, D. A. ( 1993). “The influence of selected testing procedures on soil/geomembrane shear strength measurements.” Proc., Geosynthetics '93, Industrial Fabrics Association International, St. Paul, Minn., 619–631.
5.
Bemben, S. M., and Shulze, D. A. ( 1995). “The influence of testing procedures on clay/geomembrane shear strength measurements.” Proc., Geosynthetics '95, IFAI, St. Paul, Minn., 1043–1056.
6.
Chapter NR 358, Wisconsin Administrative Code, 164-1–164-13.
7.
Bergado, D. T., and Chai, J. C. ( 1994). “Pull-out force/displacement relationship of extensible grid reinforcements.” Geotextiles and Geomembranes, 13, 295–316.
8.
Edil, T., and Benson, C. ( 1998). “Geotechnics of industrial byproducts.” Recycled materials in geotechnical applications, Geotech. Spec. Publ. No. 79, C. Vipulanandan and D. Elton, eds., ASCE, Reston, Va., 1–18.
9.
Freber, B. W. ( 1996). “Beneficial reuse of selected foundry waste material.” Proc., 19th Int. Madison Waste Conf., Dept. of Prof. Devel., University of Wisconsin, Madison, Wis., 246–257.
10.
Fredlund, D. G., Morgenstern, N. R., and Widger, R. A. ( 1978). “Shear strength of unsaturated soils.” Can. Geotech. J., Ottawa, 15(3), 313–321.
11.
Fredlund, D. G., and Rahardjo, H. ( 1993). Soil Mechanics for unsaturated soils, Wiley, New York.
12.
Fredlund, D. G., Xing, A., Fredlund, M. D., and Barbour, S. L. ( 1995). “The relationship of the unsaturated soil shear strength to the soil-water characteristic curve.” Can. Geotech. J., Ottawa, 32, 440–448.
13.
Goodhue, M. ( 1998). “Reuse of foundry sands in reinforced earth structures.” MS thesis, University of Wisconsin, Madison, Wis.
14.
Javed, S., and Lovell, C. W. ( 1994a). “Use of waste foundry sand in highway construction.” Rep. JHRP/INDOT/FHWA-94/2J, Final Rep., Purdue School of Engineering, West Lafayette, Ind.
15.
Javed, S., and Lovell, C. W. ( 1994b). “Use of waste foundry sand in civil engineering.” Transp. Res. Rec. 1486, Transportation Research Board, Washington, D.C., 109–113.
16.
Kleven, J. R., Edil, T. B., and Benson, C. H. ( 2000). “Evaluation of excess foundry system sands for use as subbase material.” Transp. Res. Rec. 1714, Transportation Research Board, Washington, D.C., 40–48.
17.
Krumbein, W. C. ( 1941). “Measurement and geological significance of shape and roundness of sedimentary particles.” J. Sedimentary Petrology, 11, 64–72.
18.
Lovejoy, M., Ham, R., Traeger, P., Hippe, J., and Boyle, W. ( 1996). “Evaluation of selected foundry wastes for highway construction.” Proc., 19th Int. Madison Waste Conf., Dept. of Prof. Devel., University of Wisconsin, Madison, Wis.
19.
Lupini, J. F., Skinner, A. E., and Vaughan, P. R. ( 1981). “The drained residual strength of cohesive soils.” Géotechnique, London, 31(2), 181–213.
20.
Mast, D. G. ( 1997). “Field demonstration of a highway embankment using waste foundry sand.” MS thesis, Purdue University, West Lafayette, Ind.
21.
Mitchell, J. K. ( 1993). Fundamentals of soil behavior, Wiley, New York.
22.
Race, R. J. ( 1995). Keystone design and operation manual, Keystone Retaining Wall Systems, Inc., Minneapolis.
23.
Simac, M. R. ( 1990). Design methodology for miragrid reinforced retaining walls, Mirafi, Inc., Charlotte, N.C.
24.
Stark, T., and Eid, H. (1994). “Drained residual strength of cohesive soils.”J. Geotech. Engrg., ASCE, 120(5), 856–871.
25.
Takasumi, D. L., Green, K. R., and Holtz, R. D. ( 1991). “Soil-geosynthetics interface strength characteristics: A review of state-of-the-art testing procedures.” Proc., Geosynthetics '91, Industrial Fabrics Association International, St. Paul, Minn., 87–100.
26.
Tatlisoz, N., Edil, T. B., and Benson, C. H. (1998). “Interaction between reinforcing geosynthetics and soil-tire chip mixtures.”J. Geotech. and Geoenvir. Engrg., ASCE, 124(11), 1109–1119.
27.
Vanapalli, S. K., Fredlund, D. G., and Pufahl, D. E. ( 1996a). “The relationship between the soil-water characteristic curve and the unsaturated shear strength of a compacted glacial till.” Geotech. Testing J., 19(3), 259–268.
28.
Vanapalli, S. K., Fredlund, D. G., Pufahl, D. E., and Clifton, A. W. ( 1996b). “Model for the prediction of shear strength with respect to soil suction.” Can. Geotech. J., Ottawa, 33, 379–392.
Information & Authors
Information
Published In
History
Received: May 19, 1999
Published online: Apr 1, 2001
Published in print: Apr 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.