Plasticity Model for Sand under Small and Large Cyclic Strains
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 127, Issue 11
Abstract
A plasticity constitutive model for sands is proposed, which combines a bounding surface framework for large cyclic strains with a Ramberg-Osgood-type hysteretic formulation for relatively smaller strains. The distinction between small and large cyclic strains is based on the volumetric threshold cyclic shear strain γtv, a well-established geotechnical parameter. The state parameter ψ is used explicitly to interrelate the critical, peak, and dilatancy deviatoric stress ratios. The plastic modulus is expressed as a particular function of accumulated plastic volumetric strain, which simulates empirically the effect of fabric evolution during shearing. Extensive comparisons with experiments show accurate simulation of the basic aspects of cyclic behavior for a wide range of cyclic strain amplitudes, specifically, (1) the degradation of shear modulus and increase of hysteretic damping with cyclic shear strain amplitude; (2) the evolving rates of shear strain and excess pore pressure (or volumetric strain) accumulation with number of cycles; and (3) the resistance to liquefaction. The 14 model parameters are proven independent of initial and drainage conditions, as well as the cyclic shear strain amplitude. The simulation of monotonic shearing is equally accurate.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Arthur, J. R. F., Bekenstein, S., Germaine, J. T., and Ladd, C. C. ( 1981). “Stress path tests with controlled rotation of principal stress directions.” Laboratory shear strength of soil, ASTM STP 740, ASTM, West Conshohocken, Pa.
2.
Arulmoli, K., Muraleetharan, K. K., Hossain, M. M., and Fruth, L. S. ( 1992). “VELACS: Verification of liquefaction analyses by centrifuge studies; laboratory testing program—Soil data report.” Res. Rep., The Earth Technology Corp.
3.
Been, K., and Jefferies, M. G. ( 1985). “A state parameter for sands.” Géotechnique, London, 35(2), 99–112.
4.
Chen, Y.-C., Ishibashi, I., and Jenkins, J. T. ( 1988). “Dynamic shear modulus and fabric: Part I, Depositional and induced anisotropy.” Géotechnique, London, 38(1), 25–32.
5.
Dafalias, Y. F., and Popov, E. P. ( 1975). “A model of nonlinearly hardening materials for complex loadings.” Acta Mechanica, 21, 173–192.
6.
Egglezos, D. N., and Bouckovalas, G. D. ( 1999). “Permanent strain and pore pressure relations for cyclic loading of sand.” Proc., 2nd Int. Conf. on Earthquake Geotech. Engrg., Vol. 1, 131–136.
7.
Gajo, A., and Wood, D. M. ( 1999). “A kinematic hardening constitutive model for sands: The multiaxial formulation.” Int. J. Numer. and Analytical Methods in Geomech., 23, 925–965.
8.
Hardin, B. O. ( 1978). “The nature of stress-strain behavior for soils.” Proc., ASCE Spec. Conf. on Earthquake Engrg. and Soil Dyn., State-of-the-art Rep., ASCE, New York, 3–90.
9.
Hueckel, T., and Nova, R. ( 1979). “Some hysteresis effects of the behavior of geological media.” Int. J. Solids and Struct., 15, 625–642.
10.
Ishihara, K., Tatsuoka, F., and Yasuda, S. ( 1975). “Undrained deformation and liquefaction of sand under cyclic stresses.” Soils and Found., Tokyo, 15(1), 29–44.
11.
Jefferies, M. G. ( 1993). “Nor-Sand: A simple critical state model for sand.” Géotechnique, London, 43(1), 91–103.
12.
Jefferies, M. G., and Been, K. ( 1987). “Use of critical state representations of sand in the method of characteristics.” Can. Geotech. J., Ottawa, 24(3), 441–446.
13.
Ladd, C. C., Foott, R., Ishihara, K., Schlosser, F., and Poulos, H. G. ( 1977). “Stress-deformation and strength characteristics.” Proc., 9th Int. Conf. on Soil Mech. and Found. Engrg., State-of-the-art rep., Vol. 2, 421–494.
14.
Li, X. S., and Dafalias, Y. F. ( 2000). “Dilatancy for cohesionless soils.” Géotechnique, London, 50(4), 449–460.
15.
Li, X. S., Dafalias, Y. F., and Wang, Z. L. ( 1999). “State-dependent dilatancy in critical-state constitutive modelling of sand.” Can. Geotech. J., Ottawa, 36(4), 599–611.
16.
Manzari, M. T., and Dafalias, Y. F. ( 1997). “A critical state two-surface plasticity model for sands.” Géotechnique, London, 47(2), 255–272.
17.
Massachusetts Institute of Technology (MIT). ( 1979). “Cyclic triaxial tests on Oosterschelde sands.” Res. Rep. R79-24, Soils Publ. No. 646, Department of Civil Engineering, Cambridge, Mass.
18.
Oda, M., Nemat-Nasser, S., and Konishi, J. ( 1985). “Stress-induced anisotropy in granular materials.” Soils and Found., Tokyo, 25(3), 85–97.
19.
Papadimitriou, A. G. ( 1999). “Elastoplastic modeling of monotonic and dynamic behavior of soils.” Doctorate thesis, Geotech. Div., National Technical University of Athens, Athens, Greece (in Greek).
20.
Papadimitriou, A. G., Bouckovalas, G. D., and Dafalias, Y. F. ( 1999). “Use of elastoplasticity to simulate cyclic sand behavior.” Proc., 2nd Int. Conf. on Earthquake Geotech. Engrg., Vol. 1, 125–130.
21.
Popescu, R., and Prevost, J. H. ( 1995). “Comparison between VELACS numerical `Class A' simulations and centrifuge experimental soil test results.” Soil Dyn. and Earthquake Engrg., 14(2), 79–92.
22.
Ramberg, W., and Osgood, W. R. ( 1943). “Description of stress-strain curve by three parameters.” Technical Note 902, National Advisory Committee for Aeronautics, Washington, D.C.
23.
Schofield, A. N., and Wroth, C. P. ( 1968). Critical state soil mechanics, McGraw-Hill, London.
24.
Seed, H. B., and Booker, J. R. (1977). “Stabilization of potentially liquefiable sand deposits.”J. Geotech. Engrg. Div., ASCE, 103(7), 757–768.
25.
Tatsuoka, F., and Ishihara, K. ( 1974). “Drained deformation under cyclic stresses reversing direction.” Soils and Found., Tokyo, 14(3), 51–65.
26.
Vucetic, M. (1994). “Cyclic threshold shear strains in soils.”J. Geotech. Engrg., ASCE, 120(12), 2208–2228.
27.
Vucetic, M., and Dobry, R. (1991). “Effect of soil plasticity on cyclic response.”J. Geotech. Engrg., ASCE, 117(1), 89–107.
28.
Wood, D. M., Belkheir, K., and Liu, D. F. ( 1994). “Strain softening and state parameter for sand modelling.” Géotechnique, London, 44(2), 335–339.
Information & Authors
Information
Published In
History
Received: Feb 22, 2000
Published online: Nov 1, 2001
Published in print: Nov 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.