Flow past Bench-Scale Vertical Ground-Water Cutoff Walls
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 126, Issue 6
Abstract
An experimental study was conducted to evaluate factors affecting flow rates past soil-bentonite (SB), geomembrane (GM), and composite geomembrane-soil (CGS) vertical cutoff walls. Intact walls and walls containing defects (inadequate keys, windows, and poor joint seals) were studied. For intact cutoff walls, CGS walls had the lowest flow rate, followed by SB and GM walls. CGS walls typically had flow rates as much as 100 times lower than comparable GM walls. Flow rates increased by a factor of 2–160 when the GM walls contained defective joints or the SB walls contained permeable windows. For all wall types, an effective key was required to achieve low flow rate past the wall. For GM walls, under seepage was not effectively controlled when the GM was placed in direct contact with the aquitard. Flow rates for GM walls placed in direct contact with the aquitard were nearly equal to the aquifer flow rate without a wall. Better control of underseepage was possible with SB and CGS walls placed in direct contact with the aquitard because the soft bentonitic backfill conformed to the surface of the aquitard. Hydraulic conductivity of unsealed joints in GM walls was estimated from flow rates past GM walls where a portion of the joint was unsealed. These hydraulic conductivities ranged between 1.8 × 10−4 and 5.6 × 10−3 cm/s.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bocchino, W., and Burson, B. (1997). “Installing a HDPE vertical containment and collection system in one pass utilizing a deep trencher.” Proc., Int. Containment Technol. Conf., U.S. DOE, U.S. EPA, and DuPont Co., 193–199.
2.
Boynton, S., and Daniel, D. (1985). “Hydraulic conductivity tests on compacted clay.”J. Geotech. Engrg., ASCE, 111(4), 465–478.
3.
Carlson, R., and Khan, F. (1997). “Cut-off wall system for subsurface liquid containment.” Proc., Int. Containment Technol. Conf., U.S. DOE, U.S. EPA, and DuPont Co., 104–110.
4.
Cavalli, N. ( 1992). “Composite barrier slurry wall.” Slurry walls: Design, construction, and quality control, STP 1129, D. B. Pual, R. R. Davidson, and N. J. Cavalli, eds., ASTM, West Conshohocken, Pa., 78–85.
5.
Dachler, R. (1936). Grundwasserstromung. Springer, Vienna.
6.
Daniel, D., and Koerner, R. (1995). Waste containment facilities: Guidance for construction, quality assurance and quality control of liner and cover systems, ASCE, New York.
7.
D'Appolonia, D. J. (1980). “Soil-bentonite slurry trench cutoffs.”J. Geotech. Engrg. Div., ASCE, 106(4), 399–417.
8.
Day, S. ( 1994). “The compatibility of slurry cutoff wall materials with contaminated groundwater.” Hydraulic conductivity and waste contaminant transport in soil, STP 1142, D. Daniel and S. Trautwein, eds., West Conshohocken, Pa., 284–300.
9.
Evans, J. ( 1991). “Geotechnics of hazardous waste control systems.” Foundation engineering handbook, 2nd Ed., H. Y. Fang, ed., Van Nostrand Reinhold, New York, 750–777.
10.
Evans, J. ( 1993). “Vertical cutoff walls.” Geotechnical practice for waste disposal, D. Daniel, ed., Chapman & Hall, London, 430–454.
11.
Evans, J. ( 1994). “Hydraulic conductivity of vertical cutoff walls.” Hydraulic conductivity and waste contaminant transport in soil, STP 1142, D. Daniel and S. Trautwein, eds., ASTM, West Conshohocken, Pa., 79–94.
12.
Filz, G., and Mitchell, J. ( 1995). “Design, construction, and performance of soil- and cement-based vertical barriers.” Assessment of barrier containment technologies: A comprehensive treatment for environmental remediation applications, R. Rumer and J. Mitchell, eds., Wiley, New York, 45–75.
13.
GeoSyntec. ( 1993). “Laboratory test results of Gundwall locking section with Hydrotite-leakage potential testing.” Proj. No. GL3398, Gundle Lining Systems.
14.
Giroud, J., and Bonaparte, R. (1989). “Leakage through liners constructed with geomembranes: Parts I and II.” J. Geotextiles and Geomembranes, 8, 27–107.
15.
Heath, R. ( 1984). “Ground-water regions of the United States.” Geological Survey Water Supply Paper No. 2242, U.S. Geological Survey, Reston, Va.
16.
Heslin, G., Filz, G., Baxter, D., and Davidson, R. (1997). “An improved method for interpreting API filter press hydraulic conductivity test results. Proc., Int. Containment Technol. Conf., U.S. DOE, U.S. EPA, and DuPont Co., 71–77.
17.
Khoury, M., Fayad, P., and Ladd, R. ( 1992). “Design, construction and performance of a soil-bentonite cutoff wall constructed in two stages.” Slurry walls: Design, construction, and quality control, STP 1129, D. B. Pual, R. R. Davidson, and N. J. Cavalli, eds., ASTM, West Conshohocken, Pa., 289–308.
18.
Koerner, R., and Guglielmetti, J. ( 1995). “Vertical barriers: Geomembranes.” Assessment of barrier containment technologies: A comprehensive treatment for environmental remediation applications, R. Rumer and J. Mitchell, eds., Wiley, New York, 95–118.
19.
Kraus, J. F., Benson, C. H., Erickson, A. E., and Chamberlain, E. J. (1997). “Freeze-thaw cycling and hydraulic conductivity of bentonitic barriers.”J. Geotech. and Geoenvir. Engrg., ASCE, 123(3), 229–238.
20.
Lee, T. ( 1998). “Physical modeling of groundwater cut-off walls.” MS thesis, University of Wisconsin-Madison, Madison, Wis.
21.
Manassero, M., Fratalocchi, E., Spanna, C., and Verga, F. ( 1995). “Containment with vertical cutoff walls.” Geoenvironment 2000, Geotech. Spec. Publ. No. 46, Y. Acar, ed., ASCE, New York, 1142–1167.
22.
Manassero, M., and Viola, C. ( 1992). “Innovative aspects of leachate containment with composite slurry walls: A case history.” Slurry walls: Design, construction, and quality control, STP 1129, D. B. Pual, R. R. Davidson, and N. J. Cavalli, eds., ASTM, West Conshohocken, Pa., 42–67.
23.
Millet, R. A., and Perez, J.-Y. (1981). “Current USA practices: Slurry wall specifications.”J. Geotech. Engrg. Div., ASCE, 107(8), 1041–1056.
24.
Millett, R., Perez, J., and Davidson, R. ( 1992). “USA practice-slurry wall specifications 10 years later.” Slurry walls: Design, construction, and quality control, STP 1129, D. B. Pual, R. R. Davidson, and N. J. Cavalli, eds., ASTM, West Conshohocken, Pa., 42–67.
25.
O'Sadnick, D., Simpson, B., and Kasel, G. ( 1995). “Evaluation and performance of a soil/bentonite liner.” Geoenvironment 2000, Geotech. Spec. Publ. No. 46, Y. Acar, ed., ASCE, New York, 688–701.
26.
Poletto, R., and Good, D. (1997). “Slurry walls and slurry trenches—Construction quality control.” Proc., Int. Containment Technol. Conf., U.S. DOE, U.S. EPA, and DuPont Co., 45–51.
27.
Ryan, C. ( 1987). “Vertical barriers in soil for pollution containment.” Geotechnical practice for waste disposal '87, 13, R. Woods, ed., ASCE, New York, 182–204.
28.
Schindler, R., and Maltese, P. (1997). “Installation of a HDPE curtain wall with sheetpile tie-in on both ends.” Proc., Int. Containment Technol. Conf., U.S. DOE, U.S. EPA, and DuPont Co., 229–234.
29.
Tachavises, C. ( 1998). “Flow rates past vertical groundwater cut-off walls: Influential factors and their impact on wall selection.” PhD dissertation, University of Wisconsin-Madison, Madison, Wis.
30.
Tachavises, C., and Benson, C. ( 1997). “Hydraulic importance of defects in vertical goundwater cut-off walls.” In situ remediation of the geoenvironment '97, Geotech. Spec. Publ. No. 71, J. Evans, ed., ASCE, New York, 168–180.
31.
Xanthakos, P. (1979). Slurry walls. Academic, San Diego, and McGraw-Hill, New York.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 126 • Issue 6 • June 2000
Pages: 511 - 520
History
Received: Mar 12, 1999
Published online: Jun 1, 2000
Published in print: Jun 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.