Evolution of Sand Microstructure during Shear
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 126, Issue 2
Abstract
Quantitative measurements of the local void ratio distribution are used to demonstrate how the microstructure throughout dilatant triaxial specimens of uniform fine quartz sand evolves during drained axial compression loading. Shear-induced increases in the mean of the local void ratio distribution initiate at the center of the specimen and migrate toward the ends of the specimen as axial strain increases. At any given strain, the mean of the local void ratio distribution is largest near the center of the specimen, reflecting the influence of end platen and membrane restraining effects. The results provide direct quantitative microstructure-based evidence that global or macro response, as conventionally used in interpreting specimen behavior, can be misleading as to the true material response. Implications of the test results on practical issues such as the location of local strain measurement systems are noted.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bhatia, S. K., and Soliman, A. F. (1990). “Frequency distribution of void ratio of granular materials determined by an image analyzer.” Soils and Found., Tokyo, 30(1), 1–16.
2.
Desrues, J., Chambon, R., Mokni, M., and Mazerolle, F. (1996). “Void ratio evolution inside shear bands in triaxial sand specimens studied by computed tomography.” Géotechnique, London, 46(2), 529–546.
3.
Frost, J. D., and Kuo, C.-Y. (1996). “Automated determination of the distribution of local void ratio from digital images.” ASTM Geotech. Testing J., 19(2), 107–117.
4.
Frost, J. D., Lee, S. W., and Cargill, P. E. (1999). “The evolution of sand structure adjacent to geomembranes,” Proc., Geosynthetics '99 Conf., Vol. 1, Industrial Fabrics Association International, Roseville, Minn., 559–573.
5.
Gilbert, P. A. (1984). “Investigation of density variation in triaxial test specimen of cohesionless soil subjected to cyclic and monotonic loading.” Tech. Rep. GL-84-10, U.S. Army Engineers Waterways Experiment Station, Vicksburg, Miss.
6.
Hilliard, J. E. ( 1968). “Measurement of volume in volume.” Quantitative Microscopy, R. T. DeHoff and F. N. Rhines, eds., McGraw-Hill, New York.
7.
Ibrahim, A. A., and Kagawa, T. (1991). “Microscopic measurement of sand fabric from cyclic tests causing liquefaction.” ASTM Geotech. Testing J., 14(4), 371–382.
8.
Jang, D. J. ( 1997). “Quantification of sand structure and its evolution during shearing using image analysis,” PhD thesis, Georgia Institute of Technology, Atlanta.
9.
Jang, D. J., and Frost, J. D. (1998). “Sand structure differences resulting from specimen preparation procedures.” Proc., ASCE Specialty Conf. on Geotech. Earthquake Engrg. and Soil Dyn. III, GSP No. 75, Vol. 1, ASCE, Reston, VA., 234–245.
10.
Jang, D. J., Frost, J. D., and Park, J. Y. (1999). “Preparation of epoxy impregnated sand coupons for image analysis.” ASTM Geotech. Testing J., 22(2), 153–164.
11.
Kuo, C.-Y., and Frost, J. D. (1996). “Uniformity evaluation of cohesionless specimens using image analysis.”J. Geotech. Engrg., ASCE, 122(5), 390–396.
12.
Ladd, R. S. (1974). “Specimen preparation and liquefaction of sands.”J. Geotech. Engrg. Div., ASCE, 100(10), 1180–1184.
13.
Ladd, R. S. (1978). “Preparing test specimens using undercompaction.” ASTM Geotech. Testing J., 1(1), 16–23.
14.
Lee, S. W. ( 1998). “Influence of surface topography on interface strength and counterface soil structure,” PhD thesis, Georgia Institute of Technology, Atlanta.
15.
Miura, S., and Toki, S. (1982). “A sample preparation method and its effect on static and cyclic deformation strength properties of sand.” Soils and Found., Tokyo, 22(1), 61–77.
16.
Oda, M. (1972a). “Deformation mechanism of sand in triaxial compression tests.” Soils and Found., Tokyo, 12(4), 45–63.
17.
Oda, M. (1972b). “Initial fabrics and their relations to mechanical properties of granular material.” Soils and Found., Tokyo, 12(1), 17–36.
18.
Oda, M. (1972c). “The mechanism of fabric changes during compressional deformation of sand.” Soils and Found., Tokyo, 12(2), 1–18.
19.
Oda, M. ( 1976). “Fabrics and their effects on the deformation behavior of sand.” Special Issue, Dept. of Found. Engrg., Fac. of Engrg., Saitama University, Japan.
20.
Shi, D., and Winslow, D. N. (1991). “Accuracy of a volume fraction measurement using areal image analysis.” ASTM J. Testing and Evaluation, 19(3), 210–213.
21.
Scholey, G. K., Frost, J. D., Lo Presti, D. C. F., and Jamiolkowski, M. (1995). “Instrumentation for Measuring Local Strains during Triaxial Testing of Small Specimens,” ASTM Geotech. Testing J., 18(2), 137–156.
22.
Shockley, W. G., and Ahlvin, R. G. (1960). “Non-uniform conditions in triaxial test specimens.” Res. Conf., Shear Strength of Cohesive Soils, ASCE, New York, 341–357.
Information & Authors
Information
Published In
History
Received: Aug 5, 1998
Published online: Feb 1, 2000
Published in print: Feb 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.