Determination of Pile Base Resistance in Sands
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 125, Issue 8
Abstract
Advances in the design of axially loaded piles are desirable because significant cost savings may result. Well-designed piles settle by amounts that are well tolerated by the superstructure and induce strains around the pile base that are far removed from failure. To investigate the development of base resistance for a given soil condition and increasing settlements, piles embedded in sand are modeled using the finite-element method with a nonlinear elastic-plastic model. Based on the load-settlement response obtained from the finite-element analysis and cone penetration resistance obtained from cavity expansion and stress rotation analyses, values of normalized base resistance, defined as base resistance divided by cone penetration resistance, are obtained. The relationship between base resistance and cone resistance is useful in the design of deep foundation using cone penetration test results. The effect of the initial coefficient of earth pressure at rest K0 on normalized base resistance values is also investigated. Several case histories, including both nondisplacement and displacement piles, are used for comparison with the theoretical results.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Albiero, J. H., Sacilotto, A. C., De Mantilla, J. N. R., Teixeira, C. Z., and Carvalho, D. (1995). “Successive load tests on bored piles.” Proc., 10th Pan-Am. Conf. of Soil Mech. and Found. Engrg., Guadalajara, Vol. 2, 991–1002.
2.
Bandini, P., and Salgado, R. (1998). “Methods of pile design based on CPT and SPT results.” Proc., 1st Int. Conf. on Site Characterization, P. Robertson and P. Mayne, eds., Balkema, Rotterdam, The Netherlands, 967–976.
3.
Bellotti, R., Jamiolkowski, M., Lo Presti, D. C. F., and O'Neill, D. A. (1996). “Anisotropy of small strain stiffness in Ticino sand.” Géotechnique, London, 46(1), 115–131.
4.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Géotechnique, London, 36(1), 65–78.
5.
Borja, R. I., Lee, S. R., and Seed, R. B. (1989). “Numerical simulation of excavation in elastoplastic soils.” Int. J. Numer. and Analytical Methods in Geomech., 13(3), 231–249.
6.
Chen, W. F., and Baladi, G. Y. (1985). Soil plasticity: Theory and implementation. Elsevier Science, New York.
7.
De Beer, E. (1984). “Different behavior of bored and driven piles.” Proc., 6th Conf. on Soil Mech. and Found. Engrg., G. Petrasovits, ed., Budapest, 307–318.
8.
De Beer, E. (1988). “Different behavior of bored and driven piles.” Proc., Deep Found. on Bored and Auger Piles, Van Impe, ed., Balkema, Rotterdam, 47–82.
9.
De Mello, V. F. B., and Aoki, N. (1993). “Updating realism on large-diameter bored piles.” Proc., 2nd Int. Geotech. Seminar on Deep Found. on Bored and Auger Piles, Van Impe, ed., Balkema, Rotterdam, The Netherlands, 35–42.
10.
Desai C. S., and Christian, J. T. (1977). Numerical methods in geotechnical engineering. McGraw-Hill, New York.
11.
Desai C. S., and Siriwarden, H. J. (1984). Constitutive laws for engineering materials with emphasis on geologic materials. Prentice-Hall, Englewood Cliffs, N.J.
12.
Duncan, J. M., and Chang, C. Y. (1970). “Nonlinear analysis of stress-strain in soils.”J. of Soil Mech. and Found. Div., ASCE, 96(5), 1629–1653.
13.
Fahey, M., and Carter, J. P. (1993). “A fine element study of the pressuremeter test in sand using non-linear elastic plastic model.” Can. Geotech. J., Ottawa, 30(2), 348–361.
14.
Fioravante, V., Ghionna, V. N., Jamiolkowski, M., and Pedroni, S. (1995). “Load carrying capacity of large-diameter bored piles in sand and gravel.” Proc., 10th Asian Regional Conf. in Soil Mech. and Found. Engrg., 1–13.
15.
Franke, E. (1989). “Co-report to discussion, session 13, on large diameter piles.” Proc., 12th Int. Conf. on Soil Mech. and Found. Engrg.
16.
Franke, E. (1993). “Design of bored piles, including negative skin friction and horizontal loading.”Proc., 2nd Int. Geotech. Seminar on Deep Found. on Bored and Auger Piles, Van Impe, ed., Balkema, Rotterdam, The Netherlands, 43–57.
17.
Ghionna, V. N., Jamiolkowsi, M., Lancellotta, R. and Pedroni, S. (1993). “Base capacity of bored piles in sands from in-situ tests.” Proc., 2nd Int. Geotech. Seminar on Deep Found. on Bored and Auger Piles, Van Impe, ed., Balkema, Rotterdam, The Netherlands, 67–74.
18.
Ghionna, V. N., Jamiolkowsi, M., Pedroni, S., and Salgado, R. (1994). “The tip displacement of drilled shafts in sands.” Proc., Settlement '94, A. Yeung and T. Felio, eds., Vol. 2, Geotech. Engrg. Div., ASCE, Reston, Va., 1039–1057.
19.
Giuseppe, B. ( 1991). “Modellazione numerica delle prove pressiometriche in camera di calibrazione per la sabbia del ticino,” MS thesis, Dipartimento Di Ingegneria Strutturale, Politecnico Di Torino, Italy.
20.
Goble, G. G., Kovacs, A. M., and Rausche, F. (1972). “Field demonstration: Response of instrumented piles to driving and load testing.” Proc., Specialty Conf. on Perf. of Earth and Earth-Supported Struct., Vol. 3, ASCE, Reston, Va., 3–38.
21.
Gregersen, O. S., Aas, G., and Dibiagio, E. ( 1973). “Load tests on friction piles in loose sand.” Proc., 8th Int. Conf. on Soil Mech. and Found. Engrg., Vol. 2, 109–117.
22.
Hardin, B. O., and Black, W. L. (1966). “Sand stiffness under various triaxial stresses.”J. Soil Mech. and Found. Div., ASCE, 92(2), 27–42.
23.
Hardin, B. O., and Drnevich, V. P. (1972). “Shear modulus and damping in soils; design equations and curves.”J. Soil Mech. and Found. Div., ASCE, 98(7), 667–692.
24.
Harris, D. E., and Mayne, P. W. (1994). “Axial compression behavior of two drilled shafts in Piedmont residual soils.” Proc., Int. Conf. Des. and Constr. of Deep Found., Vol. 2, 352–367.
25.
Harrop-Williams, K. (1989). “Risk correction factors for bearing capacity analysis.” Proc., Congr. on Found. Engrs., H. Kulhawy, ed., Vol. 2, ASCE, Reston, Va., 848–856.
26.
Hirany, A., and Kulhawy, F. H. (1989). “Interpretation of load tests on drilled shafts part 1: Axial compression.” Proc., Congr. on Found. Engrg., H. Kulhawy, ed., Vol. 2, ASCE, Reston, Va., 1132–1149.
27.
Jamiolkowski, M., and Lancellotta, R. (1988). “Relevance of in-situ test results for evaluation of allowable base resistance of bored piles in sands.” Proc., 1st Int. Geotech. Seminar on Deep Found. on Bored and Auger Piles, Van Impe, ed., Balkema, Rotterdam, 107–120.
28.
Kondner, R. L. (1963). “Hyperbolic stress-strain response: Cohesive soil.”J. Soil Mech. and Found. Div., ASCE, 189(1), 115–143.
29.
Lee, C. Y., Allman, M. A., and Poulos, H. G. (1989). “Static behavior of piles in cemented calcareous sands.” Proc., 1989 Found. Engrg. Congr., Vol. 1, ASCE, Reston, Va., 485–499.
30.
Lee, J. H. ( 1999). “Design of foundations bearing in sand based on CPT results,” PhD thesis, School of Civil Engrg., Purdue University, West Lafayette, Ind.
31.
Lee, J. H., and Salgado, R. (1999). “Analysis of calibration chamber plate load tests.” Can. Geotech. J., Ottawa, December.
32.
Mayne, P. W., and Harris, D. E. (1993). “Axial load-displacement behavior of drilled shaft foundation in Piedmont residium.” Tech. Rep. No. 41-30-2175, Federal Highway Administration, Washington, D.C.
33.
Naylor, D. J., Pande, G. N., Simpson, B., and Tabb, R. (1981). Finite elements in geotechnical engineering. Pineridge, Swansea, U.K.
34.
Poulos, H. G. (1989). “Developments in the analysis of static and cyclic lateral response of piles.” Proc., 4th Int. Conf. on Numer. Methods in Geomechanics, Vol. 3, Rotterdam, Balkema, The Netherlands, 1117–1135.
35.
Reese, L. C., and O'Neill, M. W. (1988). “Drilled shafts; construction procedures and design methods.” Rep. No. FHWA-HI-88-42, U.S. Dept. of Transp., Federal Highway Administration, Washington, D.C.
36.
Robertson, P. K., and Campanella, M. (1983). “SPT-CPT correlation.”J. Geotech. Engrg., ASCE, 109(11), 1449–1459.
37.
Salgado, R. ( 1993). “Analysis of penetration resistance in sand,” PhD thesis, Dept. of Civil Engrg., University of California, Berkeley, Calif.
38.
Salgado, R. (1995). “Design of piles in sands based on CPT results.” Proc., 10th Pan-Am. Conf. of Soil Mech. and Found. Engrg., Guadalajara, Vol. 3, 1261–1274.
39.
Salgado, R., Bandini, P., and Karim, A. (1999). “Stiffness and strength of silty sand.”J. Geotech. and Geoenvir. Engrg., ASCE, accepted for publication.
40.
Salgado, R., Boulanger, R. W., and Mitchell, J. K. (1997a). “Lateral stress effects on CPT liquefaction resistance correlations.”J. Geotech. and Geoenvir. Engrg., ASCE, 123(8), 726–735.
41.
Salgado, R., Mitchell, J. K., and Jamiolkowski, M. (1997b). “Cavity expansion and penetration resistance in sands.”J. Geotech. and Geoenvir. Engrg., ASCE, 123(4), 344–354.
42.
Salgado, R., Mitchell, J. K., and Jamiolkowski, M. (1998). “Calibration chamber size effects on penetration resistance in sand.”J. Geotech. and Geoenvir. Engrg., ASCE, 124(9), 878–888.
43.
Simonini, P. (1996). “Analysis of behavior of sand surrounding pile tips.”J. Geotech. Engrg., ASCE, 122(11), 897–905.
44.
Tatsuoka, F., Siddiquee, M. S. A., Park, C., Sakamoto, M., and Abe, F. (1993). “Modelling stress-strain relations in sand.” Soils and Found., Tokyo, 33(2), 60–81.
45.
Teixeira, C. Z., and Albiero, J. H. (1994). “A da de ponta de estacas escavadas submetidas a sucessivas provas de carga.” Proc., 10th Brazilian Conf. on Soil Mech. and Found. Engrg., Foz Do Iguacu, Vol. 1, 3–9.
46.
Trochanis, A. M., Bielak, J., and Christiano, P. (1991). “Three-dimensional nonlinear study of piles.”J. Geotech. Engrg., ASCE, 117(3), 429–447.
47.
Vecchia, G. ( 1991). “Modellazione con Il metodo degli elementi finiti delle prove triassiali E pressiometriche utilizzando la legge constitutiva di lade,” MS thesis, Dipartimeno Di Ingegneria Strutturale, Politecnico di Torino, Italy.
48.
Vilar ( 1979). “Estudo da unidirecional do sedimento moderno (solo superficial) da cidade de Carlos,” MS thesis, School of Engrg., University of Paulo, Carlos, Paulo.
Information & Authors
Information
Published In
History
Published online: Aug 1, 1999
Published in print: Aug 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.