Impact Factors for Horizontally Curved Composite Box Girder Bridges
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Bridge Engineering
Volume 9, Issue 6
Abstract
This paper presents a method for determining the dynamic impact factors for horizontally curved composite single- or multicell box girder bridges under AASHTO truck loading. The bridges are modeled as three-dimensional structures using commercially available software. The vehicle is idealized as a pair of concentrated forces, with no mass, traveling in two circumferential paths parallel to the curved centerline of bridges. An extensive parametric study is conducted, in which over 215 curved composite box girder bridge prototypes are analyzed. The key parameters considered in this study are: Number of cells, number of lanes, degree of curvature, arc span length, slope of the outer steel webs, number and area of bracing and top chord systems, and truck(s) speed and truck(s) positioning. Based on the data generated from the parametric study, expressions for dynamic impact factors for longitudinal moment, reaction, and deflection are proposed as function of the ratio of the arc span length to the radius of curvature. The results from this study would enable bridge engineers to design horizontally curved composite box girder bridges more reliably and economically. Furthermore, the results can be used to potentially increase the live-load capacity of existing bridges to prevent posting or closing of the bridge.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Akoussah, K. E., Fafard, M., Talbot, M., and Beaulieu, D. (1997). “Parametric study of dynamic load amplification factor for simply-supported reinforced concrete bridges.” Can. J. Civ. Eng., 24(2), 313–322 (in French).
2.
American Association of State Highway and Transportation Officials (AASHTO). ( 1980). Guide specifications for horizontally curved highway bridge, AASHTO, Washington, D.C.
3.
American Association of State Highway and Transportation Officials (AASHTO). ( 1993). Guide specifications for horizontally curved highway bridges, AASHTO, Washington, D.C.
4.
American Association of State Highway and Transportation Officials (AASHTO). ( 2000a). Guide specifications for horizontally curved highway bridges, AASHTO, Washington, D.C.
5.
American Association of State Highway and Transportation Officials (AASHTO). ( 2000b). “Standard specifications for highway bridges.” HS20-44, AASHTO, Washington, D.C.
6.
Galdos, N.H. ( 1988). “A theoretical investigation of the dynamic behaviour of horizontally curved steel box girder bridges under truck loadings.” Thesis, Univ. of Maryland, Collage Park, Md.
7.
Heins, C.P. ( 1978). “Box-girder bridge design state of the art.” AISC Eng. J., 2, 126–142.
8.
Hibbitt, H.D., Karlson, B.I., and Sorenson, E.P. ( 2000). ABAQUS, version 6.1, finite-element program, Hibbitt, Karlson & Sorenson, Providence, R.I.
9.
Hilber, H. M., Hughes, T. J. R., and Taylor, R. L. (1978). “Collocation, dissipation and “overshoot” for time integration schemes in structural dynamics.” Earthquake Eng. Struct. Dyn., 6, 99–117.
10.
Huang, D., Wang, T., and Shahawy, M. (1995). “Dynamic behaviour of horizontally curved I-girder bridges.” Comput. Struct., 57(4), 703–714.
11.
Huang, D. (2001). “Dynamic analysis of steel curved box-girder bridges.” J. Bridge Eng., 6(6), 506–513.
12.
Kim, S., and Nowak, A. S. (1997). “Load distribution and impact factors for I-girder bridges.” J. Bridge Eng., 2(3), 97–104.
13.
Laman, J. A., Pechar, J. S., and Boothby, T. E. (1999). “Dynamic load allowance for through-truss bridges.” J. Bridge Eng., 4(4), 231–241.
14.
Nassif, H. H., and Nowak, A. S. ( 1995). “Dynamic load spectra for girder bridges.” Transportation Research Record. 1476, TRA, National Research Council, Washington, D.C., 69–83.
15.
Newmark, N.M. ( 1959). “A method of computation for structural dynamics.” Proc., Am. Soc. Civ. Eng., 85(3), 67–94.
16.
Okeil, A. M., El-Tawil, S., and Chaphalkhar, M. ( 2000). “New hatches in existing curved box-girder bridges: A study based on practical and structural considerations.” Final Rep. to the Florida Department of Transportation (FDOT), Project No. WPI 0510839, FDOT, Tallahassee, Fla.
17.
Ontario Ministry of Transportation and Communications (OMTC). ( 1985). Geometric design standards for Ontario highways, Ontario Ministry of Transportation and Communications, Downsview, Ont., Canada.
18.
Ontario Ministry of Transportation and Communications (OMTC). ( 2000). Canadian highway bridge design code, Ontario Ministry of Transportation and Communications, Downsview, Ont., Canada.
19.
Rabizadeh, R. O., and Shore, S. (1975). “Dynamic analysis of curved box-girder bridges.” J. Struct. Div. ASCE, 101(9), 1899–1912.
20.
Samaan, M., Sennah, K.M., and Kennedy, J.B. ( 2001). “Comparative structural behavior of multicell and multiple-spine box-girder bridges.” Proc., Int. Conf. on Structural Engineering, Elsevier Science, Vol. 1, New York, 582–590.
21.
Schelling, D. R., Galdos, N. H., and Sahin, M. A. (1992). “Evaluation of impact factors for horizontally curved steel box bridges.” J. Struct. Eng., 118(11), 3203–3221.
22.
Sennah, K. M., and Kennedy, J. B. (1997). “Dynamic characteristics of simply supported curved composite multicell bridges.” Can. J. Civ. Eng., 24, 621–636.
23.
Sennah, K. M., and Kennedy, J. B. (1998a). “Vibrations of horizontally curved continuous composite cellular bridges.” Can. J. Civ. Eng., 25, 139–150.
24.
Sennah, K. M., and Kennedy, J. B. (1998b). “Shear distribution in simply supported curved composite cellular bridges.” J. Bridge Eng., 3(2), 47–55.
25.
Sennah, K. M., and Kennedy, J. B. (1999). “Simply supported curved composite cellular bridges: Simplified design method.” J. Bridge Eng., 4(2), 85–94.
26.
Sennah, K. M., and Kennedy, J. B. (2001). “State-of-the-art in design of curved box-girder bridges.” J. Bridge Eng., 6(3), 159–167.
27.
Senthilvasan, J., Brameld, G. H., and Thambiratnam, D. P. (1997). “Bridge-vehicle interaction in curved box girder bridges.” Microcomput. Civ. Eng., 12(3), 171–181.
28.
Tan, C. P., and Shore, S. (1968). “Dynamic response of a horizontally curved bridge.” J. Struct. Div. ASCE, 94(3), 761–781.
29.
Zhang, X. ( 2001). “Evaluation of impact factors of straight and horizontally curved composite concrete deck-steel cellular bridges.” MASc thesis, Dept. of Civil and Environmental Engineering, Univ. of Windsor, Windsor, Ont., Canada.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 ASCE.
History
Published online: Oct 15, 2004
Published in print: Nov 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.