Shear and Reaction Distributions in Continuous Skew Composite Bridges
This article has been corrected.
VIEW CORRECTIONThis article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Bridge Engineering
Volume 1, Issue 4
Abstract
Continuous composite steel-concrete bridges remain one of the most common types built. The proper design of new bridges and evaluation of existing ones require accurate prediction of their structural response to truck loads. North American codes of practice contain guidance for the design of right simply supported composite bridges. To design a continuous composite bridge properly, it is important to determine the maximum reactions and shears. When the bridge is skewed, the distribution of reactions and shears becomes more complicated. In this paper, the influence of skew, as well as other design parameters, on the shear and reaction distribution factors of continuous two-span composite steel-concrete bridges are investigated. Results from tests on three continuous composite steel-concrete bridge models verify the finite-element analysis for such bridges. From a parametric study, expressions for both shear and reaction distribution factors for American Association of State Highway and Transportation Officials (AASHTO) truck loading as well as for dead load are deduced. An illustrative design example is presented.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bishara, A. G., Liu, M. C., and El-Ali, N. D.(1993). “Wheel load distribution on simply supported skew I-beam composite bridges.”J. Struct. Engrg., ASCE, 119(2), 399–419.
2.
Ebeido, T., and Kennedy, J. B.(1995). “Shear distribution in simply supported skew composite bridges.”Can. J. Civ. Engrg., Ottawa, Canada, 22(6), 1143–1154.
3.
Ebeido, T., and Kennedy, J. B.(1996a). “Girder moments in simply supported skew composite bridges.”Can. J. Civ. Engrg., Ottawa, Canada, 23(4), 904–916.
4.
Ebeido, T., and Kennedy, J. B.(1996b). “Girder moments in continuous skew composite bridges.”J. Bridge Engrg., ASCE, 1(1), 37–45.
5.
Hibbitt, H. D., Karlson, B. I., and Sorensen, E. P. (1989). ABAQUS version 4-8, finite element program . Hibbitt, Karlson & Sorensen, Inc., Providence, R.I.
6.
Kennedy, J. B., and Grace, N. F.(1983). “Load distribution in continuous composite bridges.”Can. J. Civ. Engrg., Ottawa, Canada, 10, 384–395.
7.
Khaleel, M. A., and Itani, R. Y.(1990). “Live-load moments for continuous skew bridges.”J. Struct. Engrg., ASCE, 116(9), 2361–2373.
8.
Load and resistance factor design specifications. (1994). Nat. Cooperative Hwy. Res. Program, Transp. Res. Board, Nat. Res. Council, Washington, D.C.
9.
Marx, H. J., Kachaturion, N., and Gamble, W. L. (1986). “Development of design criteria for simply supported skew slab-and-girder bridges.”Rep. No. 522, Civ. Engrg. Studies, Struct. Res. Ser., Univ. of Illinois, Champaign, Ill.
10.
Nutt, R. V., Schamber, R. A., and Zokaie, T. (1988). “Distribution of wheel loads on highway bridges.”Proj. No. 12-26, Nat. Cooperative Hwy. Res. Program. Transp. Res. Board, Nat. Res. Council, Washington, D.C., 303.
11.
Ontario Highway Bridge Design Code, 3rd Ed. (1992). Ontario Ministry of Transp. and Communications, Hwy. Engrg. Div., Downsview, Ont., Canada.
12.
Standard Specifications for Highway Bridges. (1994). Am. Assn. of State Hwy. and Transp. Officials (AASHTO), Washington, D.C.
Information & Authors
Information
Published In
Copyright
Copyright © 1996 American Society of Civil Engineers.
History
Published online: Nov 1, 1996
Published in print: Nov 1996
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.