Experimental Stiffness and Seismic Response of Pallet-Type Steel Storage Rack Connectors
Publication: Practice Periodical on Structural Design and Construction
Volume 11, Issue 3
Abstract
The down-aisle lateral load-resisting systems of pallet-type steel storage racks are typically moment frames utilizing special beam-to-column moment-resisting connections. Both the stability and seismic response of racks are strongly influenced by the rotational stiffness developed by the beam-to-column connectors. The behavior of these connectors is poorly known, and consequently there is significant uncertainty as to proper values of connector stiffness and strength to use in design. This paper presents the results of down-aisle shake table tests performed on steel pallet-type storage racks fabricated from hot-rolled sections and incorporating four different bolted beam-to-column connectors. The main objectives of the tests were to determine appropriate static load connector rotational stiffness values from measured dynamic characteristics of storage racks under low amplitude vibrations, and to evaluate their response under quasi-static conditions as well as under strong earthquake ground motions. The experimental results suggest an initial static stiffness which degrades and recovers with small motions typical of in service conditions. This result may explain the poor repeatability of some testing protocols. For seismic motions, all rack specimens were able to undergo large inelastic deformations without compromising their load carrying capacity.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The project described in this paper was sponsored by Peter S. Higgins and Associates. Mr. Higgins acknowledges the support of Frazier Industrial Company which provided the material, and funded much of the work. The writers particularly acknowledge the support of William Mascharka, Dan Clapp, and Rocco Spano from Frazier Industrial Company. They also acknowledge the technical staff of the Structural Engineering and Earthquake Simulation Laboratory (SEESL) at the University at Buffalo, particularly Mr. Mark Pitman, Technical Services Manager, for their support during the execution of the tests described in this paper.
References
American National Standard Institute (ANSI). (2004). “Design, testing, and utilization of industrial steel storage racks.” ANSI MH-16.1-04, Rack Manufacturing Institute, Charlotte, N.C.
ASCE. (2002). “Minimum design loads for buildings and other structures.” ASCE/SEI 7-02, ASCE, Reston, Va.
Canadian Standard Association (CSA). (2005). “Standard for the design and construction of steel storage racks.” CSA A344.2, Mississauga, Ontario, Canada.
Chen, C. K., Scholl, R. E., and Blume, J. A. (1980a). “Earthquake simulation tests of industrial steel storage racks.” Proc., 7th World Conf. on Earthquake Engineering, Istanbul, Turkey, 379–386.
Chen, C. K., Scholl, R. E., and Blume, J. A. (1980b). “Seismic study of industrial storage racks.” Rep. Prepared for the National Science Foundation and for the Rack Manufacturers Institute and Automated Storage and Retrieval Systems (Sections of the Material Handling Institute), URS/John A. Blume & Associates, San Francisco.
Computers and Structures, Inc. (2003). SAP2000 nonlinear version 8.2.6, Berkeley, Calif.
Clough, R. W., and Penzien, J. (1993). Dynamics of structures, 2nd Ed., McGraw-Hill, New York.
Federal Emergency Management Agency. (FEMA). (2004). “The 2003 NEHRP recommended provisions for new buildings and other structures—Part 1: Provisions.” FEMA 450, Department of Homeland Security, Washington, D.C.
Federation Europeenne de la Manutention. (2003). “The Seismic Design of Static Steel Pallet Racks.” 10.2.08, Draft 04.2, Brussels, Belgium.
Filiatrault, A., Fischer, D., Folz, B., and Uang, O.-M. (2002). “Seismic testing of a two-story woodframe house: Influence of wall finish materials.” J. Struct. Eng., 128(10), 1337–1345.
Filiatrault, A., and Wanitkorkul, A. (2004). “Shake table testing of Frazier Industrial Storage pallet racks.” Rep. No. CSEE-SEESL-2004-02, Structural Engineering and Earthquake Simulation Laboratory, Dept. of Civil, Structural and Environmental Engineering, Univ. at Buffalo, Buffalo, N.Y.
Higgins, P. S. (2004). “Frazier Industrial Company connection testing for stiffness and seismic strength.” Rep. No. 06441, Peter S. Higgins and Associates, Malibu, Calif.
International Code Council (ICC). (2003). International building code, 2003 Ed., Falls Church, Va.
Krawinkler H., Parisi, F., Ibarra, L., Ayoub, A., and Medina, R. (2000). “Development of a testing protocol for wood frame structures.” CUREE Publication No. W-02, Consortium of Universities for Research in Earthquake Engineering, Richmond, Calif.
National Fire Protection Association (NFPA). (2003). “NFPA building construction and safety code.” NFPA 5000, Quincy, Mass.
National Research Council of Canada (NRCC). (1995). “National building code of Canada.” Ottawa.
Information & Authors
Information
Published In
Practice Periodical on Structural Design and Construction
Volume 11 • Issue 3 • August 2006
Pages: 161 - 170
Copyright
© 2006 ASCE.
History
Received: Jul 28, 2005
Accepted: Oct 7, 2005
Published online: Aug 1, 2006
Published in print: Aug 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.