Large-Scale Testing of Two Flat Roof Assemblies Insulated with Cellulose
Publication: Journal of Architectural Engineering
Volume 6, Issue 1
Abstract
A laboratory test using a large-scale environmental chamber has been carried out on two flat roof models fully insulated with cellulose fiber. These two models represent the most representative single-cavity flat roofs, built in Montreal between 1930 and 1970, being insulated as part of an energy conservation program. The insulating strategy consists of packing cellulose fiber in the cavity. The goal of the test program was to determine the risk of rotting of the wood structure and moisture accumulation in the roof assembly. The test was performed using real-scale huts that were exposed to 6 months of winter and summer conditions. Two roof assemblies were each divided into five roof cavities. The main variables were the mode of moisture transfer (diffusion only and diffusion combined with air exfiltration), type of vapor barrier, and air leakage paths. The construction of the huts and the monitoring plan are described. The results of the 6-month test program using seven simulated climatic conditions are presented. Wetting and drying curves for different parts of the assemblies as well as the levels of exposure to moisture are presented and analyzed.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Auger, J., and Roquet, N. (1998). Mémoires de bâtisseurs due Québec, Éditions du Méridien, Montreal.
2.
Burch, D. M., Thomas, W. C., and Mathena, L. R. (1989). “Transient moisture and heat transfer in multilayer non-isothermal walls—comparison of predicted and measured results.” Proc., ASHRAE/DOE/BTECC/CIBSE Conf., Thermal Perf. of the Exterior Envelopes of Build. IV, Atlanta, 513–531.
3.
Fazio, P., Athienitis, A. K., Marsh, C., Rao, J. (1997). “An Environmental chamber for investigation of building envelope performance.”J. Arch. Engrg., ASCE, 3(2), 97–102.
4.
Forest, T. W. (1989). “Moisture transfer through walls.” Proc., ASHRAE/ DOE/BTECC/CIBSE Conf., Thermal Perf. of the Exterior Envelopes of Build. IV, American Society of Heating, Refrigerating and Air-Conditioning Engineers, 532–542.
5.
Kumaran, M. K. (1992). “Heat, air and moisture transport through building materials and components: Can we calculate and predict?” Proc., 6th Conf. on Build. Sci. and Technol., University of Waterloo, Waterloo, Ontario, 103–144.
6.
National Building Code. (1990). Institute for Construction, National Research Council of Canada, Ottawa.
7.
Ojanen, T., and Simonson, C. (1995). “Convective moisture accumulation in structures with additional inside insulation.” Proc., DOE/ORNL/ASHRAE/BETEC Conf., Thermal Perf. of the Exterior Envelopes of Build. VII, American Society of Heating, Refrigerating and Air-Conditioning, Engineers, Atlanta, 745–752.
8.
Rose, W. B. (1994). “Conditions for mold growth in vaulted ceilings.” Proc., 1st Int. Conf. on Build. and the Environment, Building Research Establishment, London.
9.
Simpson, A., and O'Connor, D. E. (1994). “Timber frame wall: Hygrothermal properties and vapour barrier damage.” Build. Services Engrg. Res. and Technol., U.K., 15(3), 179–184.
10.
Stewart, M. B. ( 1982). “An experimental approach to the study of moisture dynamics in walls.” Moisture migration in buildings, ASTM STP 779, M. Lieff and H. R. Trechsel, eds., ASTM, West Conshohocken, Pa., 92–101.
11.
Viitanen, H. ( 1996). “Factors affecting the development of mould and brown rot decay in wooden material and wooden structures. Effects of humidity, temperature and exposure time,” Dissertation, The Swedish University of Agricultural Sciences, Department of Forest Products, Uppsala, Sweden, 58.
12.
Zarr, R. R., Burch, D. M., and Fanney, A. H. (1995). Heat and moisture transfer in wood-based wall construction: Measured versus predicted. NIST Build. Sci. Ser. 173, National Institute of Standards and Technology, Gaithersburg, Md.
Information & Authors
Information
Published In
History
Received: Oct 26, 1998
Published online: Mar 1, 2000
Published in print: Mar 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.