Development of New Durability Index for Clay Bricks
Publication: Journal of Architectural Engineering
Volume 4, Issue 3
Abstract
The use of an index to evaluate the durability of bricks has advantages over the conventional method based on the physical requirements and test procedures given in standards. An earlier study by the writers showed that the existing durability indices for clay bricks had limitations in reliably assessing durability. In that study, an index based on the pore properties of bricks, suggested by Maage, was found to have advantages over the other indices for evaluating durability. But the experimental study by the writers concluded that, in the case of certain bricks, Maage's index might not give a true measure of the frost resistance. In order to overcome its limitations, an “apparent pore size distribution” concept is suggested in this study. Correlations between the pore properties and the water absorption properties were studied, and a new durability index was derived by incorporating the water absorption properties in Maage's equation. The new index was found to overcome the limitations of Maage's index and was validated against another set of bricks.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Arnott, M. (1990). “Investigation of freeze-thaw durability.”NRC-IRC Rep. No. CR 5680.1, National Research Council of Canada, Ottawa, Ontario, Canada.
2.
Bortz, S. A., Marusin, S. L., and Monk Jr., C. B. (1990). “A critical review of masonry durability standards.”Proc., 5th North Am. Masonry Conf., University of Illinois, Urbana-Champaign, Ill., 1523–1535.
3.
“Burned clay brick (solid masonry units made from clay or shale).” (1987). CAN/CSA-A82.1–M87. Canadian Standards Association, Rexdale, Ontario, Canada.
4.
Gazzola, E. A. (1992). “A critical review of durability provisions in Canadian Masonry Materials Standards.”Proc., 6th Canadian Masonry Symp., University of Saskatchewan, Saskatoon, Saskatchewan, Canada, 449–467.
5.
Koroth, S. R., Fazio, P., and Feldman, D.(1998). “Comparative study of durability indices for clay bricks.”J. Arch. Engrg., ASCE, 4(1), 26–33.
6.
Maage, M.(1984). “Frost resistance and pore size distribution in bricks.”Mat. and Struct., Paris, France, 17(101), 345–350.
7.
Marusin, S. L.(1990). “Failure of brick with high compressive strength, low water absorption, and saturation coefficient higher than 0.80 under severe weather conditions.”Am. Ceramics Soc. Bull., 69(8), 1332–1337.
8.
“Methods of sampling and testing brick.” (1978). CAN3-A82.2-M78, Canadian Standards Association, Rexdale, Ontario, Canada.
9.
Nakamura, M.(1988). “Indirect evaluation of frost susceptibility of building materials.”Am. Ceramics Soc. Bull., 67(12), 1964–1965.
10.
PoreSizer 9320: operator's manual. (1993). Micromeritics Instrument Corporation, Norcross, Ga.
11.
Robinson, G. C., Holman, J. R., and Edwards, J. F.(1977). “Relation between physical properties and durability of commercially marketed brick.”Am. Ceramics Soc. Bull., 56(12), 1071–75.
12.
Smalley, A. R., Aitcin, P. C., and Langlois, J. L. (1987). “The correlation between mercury porosimetry and the durability of burned clay brick.”Proc., 4th North Am. Masonry Conf., Dept. of Civ. Engrg., University of California, Los Angeles, Calif., 2, 65.1–65.13.
13.
“Standard methods of sampling and testing brick and structural clay tile.” (1993). ASTM C67-93a, ASTM, West Conshohocken, Pa.
14.
“Standard specifications for facing brick (solid masonry units made from clay or shale).” (1992). ASTM C216-92d, ASTM, West Conshohocken, Pa.
15.
“Standard test method for determination of pore volume and pore volume distribution of soil and rock by mercury intrusion porosimetry.” (1984). ASTM D4404-84, ASTM, West Conshohocken, Pa.
16.
Winslow, D. N., Kilgour, C. L., and Crooks, R. W.(1988). “Predicting the durability of bricks.”J. Testing and Evaluation, 16(6), 527–531.
Information & Authors
Information
Published In
Copyright
Copyright © 1998 American Society of Civil Engineers.
History
Published online: Sep 1, 1998
Published in print: Sep 1998
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.